You can operate the answering machine by pressing dial
keys, rather than navigating through the menus. To use
the following commands, press
. A“Answer
System”A
KeyDirect commands
MDN or MCNAdjust the receiver or speaker volume
(during playback)
M1N
Repeat message (during playback)
*1
M2NSkip message (during playback)
M3NEnter the “Settings” menu
M4NPlay new messages
M5NPlay all messages
M6NPlay greeting message
M7NM6NRecord greeting message
M8NTurn auto answer setting ON
M9N or Stop recording/Stop playback
M0NTurn auto answer setting OFF
MGNM4N
*2
Erase currently playing message
MGNM5NErase all messages
MGNM6N
Erase greeting message
*3
*1If pressed within the first 5 seconds of a message,
the previous message is played.
*2You can also erase as follows:
A“Yes”A
*3Unit resets to a pre-recorded greeting message.
6.4.5 Programming for answering machine
To set the remote operation ID
A 3-digit remote access code must be entered when
operating the answering machine remotely. This code
prevents unauthorised parties from listening to your
messages remotely.
Important:
RIn order to operate the answering machine
remotely, you must first set a remote access
code.
1.
2.“Answer System”A
3.“Settings”A
4.“Remote Code”A
5.To turn ON remote operation, enter the desired
3-digit remote access code.
RTo turn OFF remote operation, press MGN.
6.AMN
Note:
RYou can also program this feature with the base unit
(feature #11 on page 42).
To change the ring count in TAM/FAX mode
You can change the number of times the unit rings
“Number of Rings” before the unit answers a call.
You can select 2 to 7 rings, or “Auto”.
The default setting is “2 Rings”.
“Auto”: The unit answers after 2 or 3 rings when new
messages have been recorded, and after 5 or 6 rings
when there are no new messages. If you call your unit
from a remote location to listen to new messages
(page 40), you will know that there are no new
messages when the unit rings for the 4th time. You can
then hang up without being charged for the call.
1.
2.“Answer System”A
3.“Settings”A
4.“Number of Rings”A
5.
Select the desired setting. AAMN
Note:
RYou can also program this feature with the base unit
(feature #06 on page 42).
To change the maximum recording time for
incoming messages
You can change the maximum message recording time
allotted to each caller. You can also select “Greeting
Only” which sets the unit to greet callers but not record
messages. The default setting is “3 Minutes”.
1.
2.“Answer System”A
3.“Settings”A
4.“Recording Time”A
5.Select the desired setting. AAMN
Note:
RWhen you select “Greeting Only”:
–If you do not record your own message, the unit
will play the pre-recorded greeting-only message
asking callers to call again later.
–If you use your own message, record the
greeting-only message asking callers to call
again later (page 39).
RYou can also program this feature with the base unit
(feature #10 on page 42).
6.5 Operating from a remote
location
Using a touch-tone telephone, you can call your
telephone number from outside and access the unit to
listen to messages or change auto answer settings.
40
6. Answering Machine
Manual
View the manual for the Panasonic KX-FC275E here, for free. This manual comes under the category fax machines and has been rated by 1 people with an average of a 8.8. This manual is available in the following languages: English. Do you have a question about the Panasonic KX-FC275E or do you need help? Ask your question here
Need help?
Do you have a question about the Panasonic and is the answer not in the manual?
Question and answer
Number of questions: 0