Pacific PR-2107 manual

6.5 · 1
PDF manual
 · 12 pages
English
manualPacific PR-2107
3.
3.

三.安裝原則

1.安裝前請先檢查

l. 附件說明書風管圈
ll. 性能上電源檢查照明與馬達鍵是否正常

lll.此電器必須接上地線以免導致受傷或損壞

2.風管長度

使用直徑8吋的風管更能提高排風之效率

排風出口至機體之距離應盡量避免過長以免氣流擠壓於管內影

響其排風效果

抽油煙機之安裝高度係指爐面至機身底面之距離建議參考高度

26-30 抽油煙機若能越接近爐面則其排煙效果越佳

3.理想安裝位置

安裝於爐台之上方抽油煙機底部邊緣距地面約在

62 – 64 吋之間
(油煙機底部與瓦斯爐上方不得超過30)

4.鑽穿牆洞

先量好彎管正對牆面位置釘頭與牆壁間最多保持1/4 吋距離做掛

勾之用此舉有助機身保持水平

然後在壁面畫好鑽洞範圍再使用電鑽鑽穿牆壁鑽洞時應要留意

牆壁結構和質料切勿破壞牆洞以外之璧面

裝設機身及排氣管已選定的安裝位置釘上
調

懸掛後機身要保持一定水平

按已選好排氣管的適當位置選擇適當長度的直管進行裝設

本風管座已在出廠前套入出風口安裝時請將風管照一般方式反

方向入即前先強力注入管圈將風圈崁

用封膠封住風管圈以避免清潔劑泡沫流出

III. Installation Guidelines

A. Please Inspect the Following Before Installation:

l. Enclosed Items: manual, duct collar, oil cup

ll. Performance: Check if light and motor switch appear normal after

connecting the power.

lll. This electrical appliance must be connected to the ground outlet to avoid

accidents or damaging the appliance.

B. Exhaust Pipe Length:

Using an 8-inch diameter exhaust pipe can improve ventilation efficiency.The

distance from the exhaust opening to the body of the hood should not be too

long. Otherwise, the airflow gets trapped inside the pipe and affects the

exhaust function.The ideal distance from the range hood to the stove top should

be 26-30 inches. This distance should be measured from the bottom of the range

hood to the top of the stove.The closer the range hood is to the stove top the

more effective the exhaust ventilation.

C. Ideal Installation Position:

The range hood should be installed with the bottom edge of the range hood

62-64 inches from the floor. (The distance between the bottom of the range

hood and the top of the gas stove should not exceed 30 inches).

D. Drilling a Hole on the Wall:

Measure the spot on the wall where the L-shape exhaust pipe will be placed.

The screw heads should stick out ¼ inches from the wall for the range hood

to be mounted, which also allows the range hood to stay leveled when installed.

Then make marks on the wall where you are going to drill the holes. Before

drilling holes in the wall, be sure to check the structure of the wall and the

material behind the wall so it will not be damaged after drilling.

Then proceed to drill holes on the marked areas.

Installing range hood and exhaust pipe:

Install the screws into the wall on marked areas. Adjust the hooks (hanging rail)

on both sides of the range hood and hang the range hood on the screws.

After the range hood is mounted, check to make sure it’s balanced.

Based on the position marked for the exhaust pipe, pick a straight pipe cut to

an appropriate length and install. An air outlet has been attached to the exhaust

pipe unit before leaving the factory. Attach the exhaust pipe to the straight pipe

where the two units connect. Before installation, put some glue on the inside

ring of the exhaust pipe opening, so the pipes can be securely attached.

Then secure the attachment point with plastic tape to prevent cleaning foams

from leaking during cleaning.

Manual

View the manual for the Pacific PR-2107 here, for free. This manual comes under the category exhaust hoods and has been rated by 1 people with an average of a 6.5. This manual is available in the following languages: English. Do you have a question about the Pacific PR-2107 or do you need help? Ask your question here

Need help?

Do you have a question about the Pacific and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Pacific PR-2107 specifications

Below you will find the product specifications and the manual specifications of the Pacific PR-2107.

General
BrandPacific
ModelPR-2107
Productexhaust hood
LanguageEnglish
FiletypeUser manual (PDF)

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Pacific PR-2107 below.

When should I replace the carbon filter on my extractor hood?

The carbon filter should be replaced every three to twelve months.

How often should I clean the metal hood grease filters?

The metal grease filters should be cleaned every eight to ten weeks.

Where can I find the model number of my cooker ectractor hood?

The model number of the hood is usually found on a white label inside the hood.

Is the manual of the Pacific PR-2107 available in English?

Yes, the manual of the Pacific PR-2107 is available in English .

Is your question not listed? Ask your question here

No results