Olight S80 Baton manual

Olight S80 Baton
9.3 · 1
PDF manual
 · 1 page
English
manualOlight S80 Baton
S80 Baton maintains Olight S seriess simple, reliable and easy of use advantages. A customized 4000mAh
26650 lithium rechargeable battery inside, integrated charge port, output up to 750lumens. It is a preferred
flashlight for household illumination, outdoor and industry field application.

Olight Technology Co., Limited

www.olightworld.com

Tel: +86-755-3351 8606

Fax: +86-755-3380 0207

Email: service@olightworld.com

TM

Operator's Manual

LED Flashlight

S80 BATON

Diffuser
Holster
Customized 26650 Lithium
Rechargeable Battery
Supplied Accessories
Specification
2
4
5
6
3
Key-ring
Operation Instrution
Operators Manual ( this manual)
Charger
Warranty
1
9
7

size:147*105

TM
WE MAKE A DIFFERENCE
S80 Baton手持Olight S 系简洁坚固易用 制4000毫时 26650可
到750流。 S80是家明,外及业领用的选产
征, 它
制 26650 可
即时点亮:关机状态下, 按下开关按键并保持1秒或以上, 按下时开,释放时关 。
开、关机: 按下开关按键并在1秒内释放。每次开机,手电输出在前次关机时记忆的亮度级。
改变模式: 开机状态下,按住开关按键并保持,手电输出亮度在"低-中-高"之间循环,释放按键
将选定当前的亮度。
暴闪模式: 快速连按开关按键二次(初始状态为关需按三次)。在暴闪状态下,按下开关,1秒内
释放,输出关闭;如超出1秒,输出记忆的亮度。
锁按键: 开机状态下,按下开关按键并保持,输出经历 “低-中-高”循环三次后自动关闭,
手电进入锁定状态;在锁定状态, 如开关按键被意外按下, 手电不会开机,开关按键
处的灯将点亮1秒。
解 锁: 在锁定状态,需快速连击按键三次解锁并开机。重新装入电池也会自动解锁。
充 电: 连接充电器到电源插板或墙壁插孔, 揭开手电尾端充电接口软塞,将充电器DC插头插
入。充电状态指示灯位于充电器。 指示灯显示状态:
红色 -- 充电进行中; 绿色 -- 充电完成或未连接手电。
充电完成后,将充电器从电源插板或墙壁插孔取下, 请拔出DC插头,并塞紧充电接
口软塞。
警告 充电完成后,请及时断开电源,勿将充电器长时间连接到市电;不充电
时,请勿将手电连接到充电器 。
更换电池: 请使用厂家提供的电池。 先逆时针方向旋开手电尾盖,将电池取出后,将入新电
池;电池正极朝向手电前端装入,然后旋紧尾盖。见以下电池极性标识图:
1 发
2 透
3 不
4 开
5 筒
6 尾
7 软
/ 钥
8 充
9 充
体 积
重 量
颜 色
开 关
透 镜
电 池
级 / 运
防 水
示 / 低

size:147*105

册 (本册)
规 格
规 格
6N01-T6 铝氧化
径 39.6毫米 / 筒径 32.5毫米 / 总度 154毫
277克 (
关 + 硅
水膜
Cree XM-L
制4000毫时 26650可
10流明 / 80小时 ; 180流明 / 8小时; 750流明 / 2小
,10赫
16650 坎
260 米
2米, 6个向2次
IPX8
于3.10.05时, 开隔3秒的速闪动,
档, 最于3.15 伏 时±0.05
流 100240伏 50/60赫兹; 输出: 恒流恒压 1安掊 4.2伏
约5小
度达约85度在10分内,
的60% 然在这
Characteristics
Material
Bezel
Size
Weight
Color
Reflector
Switch
Lens
LED
Battery
Flux / Runtime
Special Mode
Peak beam intensity
Max Beam Distance
Impact Strength
Waterproof
Low Battery Prompt / LVSD
Charger
Charging time
Active thermal management(ATM)
Key-ring Hole
6N01-T6 AL, Class-III harden anodization treating
Stainless Steel
Head D39.6mm / Body D32.5mm / Total Length 154mm
277g ( with battery)
Black
Orange peel, aluminum machining
Side button switch
Hardened glass, double sides AR coating, single side anti-water coating
Cree XM-L LED
Customized 4000mAh 26650 lithium rechargeable battery
10 lm / 80h; 180 lm / 8h; 750 lm / 2h
Strobe 10hz, 750lm
16650cd
260meters
2 meters dropping, 6 directions, twice each.
IPX8
Input: 100 to 240 VAC, Output: CC/CV 1A4.2V
About 5 hours
Locating at fixing screw of soft-cover in the tail cap
Under off status, press the button switch and hold 1 second or above, the light turns on
at moment that the button switch is pressed and turns off when the button switch is
released.
Press then release the button switch within 1 second. Every restart, output brightness
keeps same as previous memorized brightness.
While on, press and hold the button switch, output will change by the order “Low-
Medium-High", releasing the button switch will froze the output at presented
brightness.
Quickly press the button switch twice (if initial status is off, triply press)。Under strobe
status, pressing then releasing the button switch whin 1 second will turn off the output, if
the hold time over 1 second, the light restores to memorized brightness
While on, hold the button switch until the light becomes off. Usually the output will
experience three loops ofLow-Medium-Highbefore entering into off; Under lock
status, the hidden lamp under the button switch will turn on 1 second while the button
switch is unexpectedly pressed, but the light will not turn on.
Triply click the button switch within 1 second or reinstall after taking out the battery.
Connect the charger to AC power source or wall socket, then discover the soft-cover
and insert DC plug of charger into the charge port. The indication of the charger displays
the charge status. See below:
Red -- charging in progressGreen -- completed or not connected
When charge completed, please take off the charger from AC power source or wall
socket, and pull out the DC plug , insert the soft-cover into his seat.
Dont always connect the charge with AC power source after charge
completed, it may cause to fire. Dont long time connect DC plug together
with the flashlight while no charge.
2
4
5
6
3
1
8
9
7
8
Specification
1 LED
2 Lens
3 Stainless Steel Bezel
4 Button Switch
5 Body
6 Tail Cap
7 Fixing Screw of Soft-cover
/ Key-ring Hole
8 Charge Port
9 Soft-cover
Parts of the Flashlight
Momentary On:
Turn ON/OFF:
Change Mode:
Strobe:
Lock Button Switch:
Unlock:
Charge:
Warning
Replacing Battery:
Please using the factory supplied battery. Firstly, counterclockwise unscrew and take
out the tail cap, then take out the battery and insert the fresh battery, the positive of
battery should towards the head of the flashlight. Refer to below figure
充电输入正
负极( 充电输入负)
When internal MCU detects the inner temperature over 85within next
10 minutes, it will make regular and controls the output smoothly drop
to 60% of maximum brightness, then staying at this brightness level
When battery voltage drops to , the lamp under the button
switch will flash twice per 3 seconds interval, and the output will
automatically jump to lower brightness level. If the flashlight is running at
low brightness level, MCU will shut off the power supply.
3.15±0.05V
Positive
Negative( Charge Input-)
Charge Input+

Manual

View the manual for the Olight S80 Baton here, for free. This manual comes under the category Torches and has been rated by 1 people with an average of a 9.3. This manual is available in the following languages: English. Do you have a question about the Olight S80 Baton or do you need help? Ask your question here

Index

Need help?

Do you have a question about the Olight and the answer is not in the manual? Ask your question here. Provide a clear and comprehensive description of the problem and your question. The better your problem and question is described, the easier it is for other Samsung Galaxy A7 owners to provide you with a good answer.

Rob Stewart • 5-6-2017 No comments

My Olight S80 baton seems to be stuck in low mode . Even the strobe is at low setting . Olight is fully charged . How do I unlock it ?

Answer this question
Rob Stewart • 5-6-2017 No comments

My Olight S80 baton seems to be stuck in low mode . Even the strobe is at low setting . Olight is fully charged . How do I unlock it ?

Answer this question
adam • 27-4-2014 No comments

My Olight S80 is stuck on the low setting. How do I reset the light so that it can be used on all 3 light modes ?

Answer this question

Number of questions: 3

Olight S80 Baton specifications

Below you will find the product specifications and the manual specifications of the Olight S80 Baton.

When performance is your priority, rely on proven, trusted technology. With the cylindrical lithium-ion battery cell you...
General
Brand Olight
Model S80 Baton
Product Torch
EAN 6950723818311, 6950723818281
Language English
Filetype PDF
Design
Flashlight type Hand flashlight
Waterproof
Product colour Black
Housing material -
Shockproof up to 1.5 m
Lighting
Bulb power - W
Lamps quantity 1 lamp(s)
Number of power levels 3
Luminous flux 750 lm
Light beam distance (max) 260 m
Power
Number of batteries supported 1
Battery life (max) 80 h
Battery technology Lithium-Ion (Li-Ion)
Weight & dimensions
Width 154 mm
Depth 39.6 mm
Height 39.6 mm
Packaging data
Quantity per pack 1 pc(s)
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Olight S80 Baton below.

Is your question not listed? Ask your question here

No results