Norlake AdvantEDGE NLTF49-S manual

Norlake AdvantEDGE NLTF49-S
7 · 1
PDF manual
 · 10 pages
English
manualNorlake AdvantEDGE NLTF49-S
1 07/20 171226 Rev B

TOP MOUNT

REFRIGERATORS, FREEZERS

Installation, Operation and Maintenance Instructions

INSPECTION

When the equipment is received, all items should be carefully checked against the Bill of

Lading to ensure all crates and cartons have been received. Do not sign the freight bill

clear until the freight has been properly inspected for damage. All units should be

inspected for damage including concealed damage by uncrating immediately. If any

damage is found, it should be reported to the carrier at once, noted on the Bill of Lading

and a claim should be filed with the carrier. This equipment has been inspected and tested

in the manufacturing facility and has been crated in accordance with transportation rules

and guidelines. The manufacturer is not responsible for freight loss or damages.

INSTALLATION

CAUTION: This unit uses a flammable refrigerant. Use care when handling and

operating to avoid damaging the refrigerant tubing or increasing the risk of a leak.

The unit has been secured to the shipping base with four bolts. Remove these bolts and

separate the unit from the shipping base. Locate the casters or legs found inside the unit.

Attach the casters or legs to the unit base by screwing them into the threaded fittings that

were used to secure the shipping base. Use the wrench provided to tighten the casters to

the unit. The casters with the brakes should be installed on the front of the unit. For proper

drainage of condensate, the unit should be level when placed in its permanent location.

Leveling shims are included in the accessories package in the cabinet. Loosen the casters

and insert shims between caster and bottom of the unit. Re-tighten the caster.

The exterior of the cabinet and doors have been protected by a plastic covering. Peel this

protective covering before installation. After removing the covering, clean the interior and

exterior surfaces of the unit with soap and water and a rinse with clean water. Do not use

chlorinated cleaners on the surfaces as they can cause corrosion.

If the door(s) have come out of alignment during shipping, they will need to be adjusted.

This can be accomplished by opening the door(s) and loosening the screws that hold both

the top and bottom hinges to the cabinet. After adjusting the door so it is aligned correct,

tighten the screws to securely hold the hinges and door(s) in place.

The shelves and shelf clips are packaged inside the unit. Install the shelf clips on the

pilasters inside the unit and set the shelves on the clips. The shelves are adjustable in

12.7mm(½inch)increments.

View the manual for the Norlake AdvantEDGE NLTF49-S here, for free. This manual comes under the category freezers and has been rated by 1 people with an average of a 7. This manual is available in the following languages: English. Do you have a question about the Norlake AdvantEDGE NLTF49-S or do you need help? Ask your question here

Need help?

Do you have a question about the Norlake and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

The Norlake AdvantEDGE NLTF49-S freezer is a commercial-grade storage unit designed to keep your frozen goods at a consistent and safe temperature. This chest-style freezer has a storage capacity of 22.7 cubic feet and is constructed with a durable stainless steel exterior that provides protection against damage and corrosion. The NLTF49-S features a manual defrost system, letting you control when and how you remove the frost buildup. The interior is made of aluminum and has six adjustable dividers, allowing you to configure the storage space according to your specific needs. The freezer's temperature is maintained by a high-quality refrigeration system that works to keep the interior at temperatures ranging from -10 to 0 degrees Fahrenheit. This powerful system ensures that your frozen goods are always kept at the optimal temperature, ensuring their safety and freshness. The NLTF49-S is also equipped with a lockable lid that provides an additional layer of security against unauthorized access. The lid also features an integrated handle, allowing for easy opening and closure. Overall, the Norlake AdvantEDGE NLTF49-S is a reliable and efficient freezer option for commercial settings, such as restaurants, cafeterias, or convenience stores.

General
BrandNorlake
ModelAdvantEDGE NLTF49-S
Productfreezer
LanguageEnglish
FiletypeUser manual (PDF)

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Norlake AdvantEDGE NLTF49-S below.

How often should I defrost my freezer?

It is recommended to completely defrost your freezer at least once every six months.

How should I transport a freezer?

A freezer must be transported upright at all times. It is very bad for a freezer to be transported on its side as oil from the compressor can end up in the evaporator.

What do I do about a smelly freezer?

A commonly used method is to temporarily place a cup of vinegar in the freezer.

How do I adjust the temperature of the Norlake AdvantEDGE NLTF49-S freezer?

To adjust the temperature of the Norlake AdvantEDGE NLTF49-S freezer, follow these steps: 1. Press the "Mode/Set" button on the electronic control panel. 2. Use the "Up" or "Down" button to navigate until "<St>" is displayed. 3. Press the "Mode/Set" button again to show the current temperature set point. 4. Use the "Up" or "Down" buttons to adjust the temperature to your desired set point. 5. Press the "Mode/Set" button to set the new value. 6. Use the "Up" or "Down" button until "<th>" is displayed. 7. Press the "Verify" button to return to the display of the cabinet temperature. Please note that the temperature set point can be adjusted within the range of -22℉(-30℃) to +8℉(-10℃) for freezers. The default set point is -5℉(-20℃) for freezers. Remember to allow the freezer some time to reach the newly set temperature.

How do I set the temperature differential for the Norlake AdvantEDGE NLTF49-S freezer?

To set the temperature differential for the Norlake AdvantEDGE NLTF49-S freezer, follow these steps: 1. Press the "Mode/Set" button on the electronic control panel. 2. Use the "Up" or "Down" button until "<di>" is displayed. 3. Press the "Mode/Set" button to view the current temperature differential setting. 4. Use the "Up" or "Down" button to adjust the temperature differential to your desired value. 5. Press the "Mode/Set" button to set the new value. 6. Use the "Up" or "Down" button until "<th>" is displayed. 7. Press the "Verify" button to return to the display of the cabinet temperature. The temperature differential is the amount of swing that the cabinet temperature does on either side of the temperature set point. The default temperature differential set point is +8℉(+4℃), and the range is +4℉(+2℃) to +16℉(+10℃). Remember to allow the freezer some time to adjust to the new temperature differential setting.

What are the specifications of the Norlake AdvantEDGE NLTF49-S freezer?

The specifications of the Norlake AdvantEDGE NLTF49-S freezer are as follows: - Product: Solid Full Door Freezer - Capacity: 1,236 liters (43.7 ft³) - Exterior Dimensions (including Casters, Door handles): Width 1,390mm (54.7"), Depth Cabinet - 790mm (31.1") / 840mm (33.1"), Height 2,098mm (82.6") – 4" Casters - Swing Doors: 2 - Shelves: 6 - Compressor: 3/4HP - Power Voltage: 115V / 60Hz - Plug In-Installation: NEMA 5-15P - Amps: 7.0A - Temperature Range: 0℃ ~ 4℃ (32°F ~ 40°F) - Refrigerant: R-290, 105g (3.7 oz) - Product Weight: 178kg (392 lb) Please note that these specifications are subject to change without prior notice for quality improvement.

How do I start and stop the rapid freeze mode on the Norlake AdvantEDGE NLTF49-S freezer?

To start and stop the rapid freeze mode on the Norlake AdvantEDGE NLTF49-S freezer, follow these steps: 1. Locate the electronic control panel on the freezer. 2. Press the "Mode/Set" button to access the control settings. 3. Use the "Up" or "Down" button until "<RF>" is displayed. 4. Press the "Mode/Set" button to activate the rapid freeze mode. 5. The rapid freeze mode will start, and the freezer will rapidly cool down to the lowest temperature setting. 6. To stop the rapid freeze mode, press the "Mode/Set" button again. 7. The rapid freeze mode will be deactivated, and the freezer will return to its normal cooling mode. Please note that the rapid freeze mode is designed to quickly freeze items in the freezer. It is recommended to use this mode for a limited duration to prevent excessive cooling and potential damage to the stored items.

How do I navigate and use the electronic control settings on the Norlake AdvantEDGE NLTF49-S freezer?

To navigate and use the electronic control settings on the Norlake AdvantEDGE NLTF49-S freezer, follow these steps: 1. Press the "Mode/Set" button on the electronic control panel to access the control settings. 2. Use the "Up" or "Down" button until "<St>" is displayed to set or adjust the cabinet temperature. 3. Press the "Mode/Set" button to display the current temperature set point. 4. Use the "Up" or "Down" buttons to adjust the temperature to your desired set point. 5. Press the "Mode/Set" button to set the new value. 6. Use the "Up" or "Down" button until "<di>" is displayed to set the temperature differential. 7. Press the "Mode/Set" button to view the current temperature differential setting. 8. Use the "Up" or "Down" button to adjust the temperature differential to your desired value. 9. Press the "Mode/Set" button to set the new value. 10. To start the rapid freeze mode (for freezers only), press the "Mode/Set" button and navigate until "<tb>" is displayed. 11. Press the "Mode/Set" button for two seconds to start the rapid freeze mode. 12. To stop the rapid freeze mode, press the "Mode/Set" button for two seconds. Please note that the rapid freeze mode will run the compressor continuously for 120 minutes and then return to normal operation and set points.

Is the manual of the Norlake AdvantEDGE NLTF49-S available in English?

Yes, the manual of the Norlake AdvantEDGE NLTF49-S is available in English .

Is your question not listed? Ask your question here

No results