NEC MultiSync EA271Q manual

NEC MultiSync EA271Q
6.7 · 1
PDF manual
 · 39 pages
English
manualNEC MultiSync EA271Q
English-28

Troubleshooting

No picture
• Make sure the signal cable is fully connected to both the monitor and the computer.
• Make sure the computer’s display card is fully seated in its slot.
• Do not use a DisplayPort converter adapter. This device is not supported.
• Make sure both the computer and monitor power switches are in the ON position.
• Themonitorwillautomaticallyturnoffbythe“POWERSAVETIMER”functionwhenthe“POWER SAVE TIMER” setting
is “ON” and continues in power save mode for 2 hours. Please touch the power key.
• Make sure that a Major Supported Timings has been selected for the display card in the system being used.
(Please consult the manual for the system or display card for supported resolution and changing the settings).
• Checkthemonitorandyourdisplaycardwithrespecttocompatibilityandrecommendedsettings.
• Checkthesignalcableconnectorforbentorpushed-inpins.
• Make sure the connected device outputs a signal to the monitor.
• IfthefrontLEDisdarkblue,checkthestatusoftheOFFMODESETTINGmode(seepage 15) or HUMAN SENSING
(see page 16).
Power Key does not respond
• Unplug the monitor power cable from the AC outlet to turn off and reset the monitor.
Image Persistence
• Imagepersistenceiswhenaresidualor“ghost”imageofapreviousimageremainsvisibleonthescreen.UnlikeCRT
monitors, LCD monitors’ image persistence is not permanent, but constant images being displayed for a long period
of time should be avoided. To alleviate image persistence, turn off the monitor for as long as the previous image was
displayed. For example, if an image was on the monitor for one hour and a residual image remains, the monitor should
be turned off for one hour to erase the image.
NOTE: As with all personal display devices, NEC DISPLAY SOLUTIONS recommends using a moving screen saver at
regular intervals whenever the screen is idle or turning off the monitor when not in use.
Message “OUT OF RANGE” is displayed (screen is either blank or shows rough images only)
• OSD warning “OUT OF RANGE” is displayed on a rough image (pixels are missing): Either the signal clock or resolution
is too high. Change the settings to a supported mode.
• OSD warning “OUT OF RANGE” is displayed on a blank screen: The signal frequency is out of range. Change the
settings to a supported mode.
Image is unstable, unfocused or swimming is apparent
• Signalcableshouldbecompletelyattachedtothecomputer.
• UsetheOSDImageAdjustcontrolstofocusandadjustthedisplaybyincreasingordecreasingtheneadjustment.
When the display mode is changed, the OSD Image Adjust settings may need to be readjusted.
• Checkthemonitorandyourdisplaycardwithrespecttocompatibilityandrecommendedsignaltimings.
• Ifyourtextisgarbled,changethevideomodetonon-interlaceanduse60Hzrefreshrate.
LED on monitor is not lit (no blue or amber color can be seen)
• PowerSwitchshouldbeintheONpositionandpowercordshouldbeconnected.
• IncreaseLEDBRIGHTNESSadjustment.
Picture is not bright
• MakesureECOMODEandAUTOBRIGHTNESSareturnedoff.
• Ifthebrightnessuctuates,makesureAUTOBRIGHTNESSisturnedoff.
• Signalcableshouldbecompletelyattached.
• LCDbrightnessdegradationoccursduetolong-termusageorextremecoldconditions.
• WhenusinganHDMIinput,pleasechange“VIDEOLEVEL”.
• If the brightness fluctuates, make sure DV MODE is set to STANDARD.
Display image is not sized properly
• UsetheOSDImageAdjustcontrolstoincreaseordecreasetheCoarseadjustment.
• Make sure that a Major Supported Timings has been selected for the display card in the system being used.
(Please consult the manual for the system or display card for supported resolution and changing the settings.)
• WhenusinganHDMIinput,pleasechange“OVERSCAN”.
• Pleasecheck“TILEMATRIX”and“180°ROTATE”settings.

Manual

View the manual for the NEC MultiSync EA271Q here, for free. This manual comes under the category monitors and has been rated by 1 people with an average of a 6.7. This manual is available in the following languages: English. Do you have a question about the NEC MultiSync EA271Q or do you need help? Ask your question here

Need help?

Do you have a question about the NEC and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

NEC MultiSync EA271Q specifications

Below you will find the product specifications and the manual specifications of the NEC MultiSync EA271Q.

General
BrandNEC
ModelMultiSync EA271Q | 60004303
Productmonitor
EAN5028695116214
LanguageEnglish
FiletypeUser manual (PDF), Energy label (PDF)
Display
Display diagonal27 "
Display resolution2560 x 1440 pixels
Display brightness (typical)350 cd/m²
Response time6 ms
3DNo
HD typeQuad HD
Display technologyLCD
Panel typePLS
Supported graphics resolutions2560 x 1440
Screen shapeFlat
Pixel pitch0.23 x 0.23 mm
Backlight typeW-LED
Contrast ratio (typical)1000:1
Native aspect ratio16:9
Display number of colors16.78 million colors
Adobe RGB coverage78.3 %
sRGB coverage (typical)100 %
NTSC coverage (typical)74.6 %
Viewable size, horizontal596.74 mm
Viewable size, vertical335.66 mm
Viewing angle, horizontal178 °
Viewing angle, vertical178 °
Horizontal scan range31.5 - 94 kHz
Vertical scan range56 - 75 Hz
DDC/CIYes
Contrast ratio (dynamic)7000:1
Maximum refresh rate60 Hz
TouchscreenNo
Ports & interfaces
Built-in USB hubYes
DisplayPorts quantity2
HDMI ports quantity1
DVI portYes
DVI-D ports quantity1
USB upstream port typeUSB Type-B
USB Type-A downstream ports quantity2
Number of upstream ports1
DisplayPort version1.2
USB Type-C downstream ports quantity1
USB hub version3.2 Gen 1 (3.1 Gen 1)
HDCPYes
VGA (D-Sub) ports quantity0
Power
Power consumption (typical)37 W
Power consumption (PowerSave)0.29 W
Power consumption (max)150 W
AC input voltage100 - 240 V
AC input frequency50 - 60 Hz
Power consumption (standby)- W
E
-
21 kWh
- kWh
Energy efficiency scaleA to G
Weight & dimensions
Bezel width (side)1 mm
Bezel width (bottom)17.7 mm
Bezel width (top)1 mm
Width (without stand)611.8 mm
Depth (without stand)67.2 mm
Height (without stand)361.9 mm
Width (with stand)611.8 mm
Depth (with stand)150 mm
Height (with stand)378 mm
Weight (without stand)5700 g
Weight (with stand)9100 g
Packaging data
Package weight11800 g
Package width730 mm
Package depth217 mm
Package height475 mm
Ergonomics
VESA mountingYes
Panel mounting interface100 x 100 mm
Cable lock slotYes
Height adjustmentYes
Tilt adjustmentYes
SwivelingYes
PivotYes
On Screen Display (OSD)Yes
Plug and PlayYes
Cable lock slot typeKensington
Height adjustment150 mm
Tilt up angle range0 - 35 °
Tilt down angle range0 - 5 °
Pivot angle-90 - 90 °
Swivel angle range0 - 340 °
Other features
On/off switchYes
AC adapter includedYes
TV tuner integratedNo
Operational conditions
Operating temperature (T-T)5 - 35 °C
Storage temperature (T-T)-10 - 60 °C
Operating relative humidity (H-H)20 - 80 %
Storage relative humidity (H-H)10 - 85 %
Operating altitude0 - 5000 m
Non-operating altitude5000 - 12192 m
Sustainability
Sustainability certificatesRoHS, ENERGY STAR
391424
Design
CertificationTCP 7.0
Market positioning-
Product colorBlack
Feet colorBlack
Multimedia
Built-in speaker(s)Yes
Built-in cameraNo
Number of speakers2
RMS rated power2 W
Performance
NVIDIA G-SYNCNo
AMD FreeSyncNo
Logistics data
Harmonized System (HS) code85285210
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the NEC MultiSync EA271Q below.

What screen dimensions does my monitor have?

The size of your monitor is usually expressed in inches, 1 inch is 2.54 centimetres. The size is the diagonal size of your monitor, so you measure the screen from bottom left to top right.

What is HDMI?

HDMI stands for High-Definition Multimedia Interface. An HDMI cable is used to transport audio and video signals between devices.

What certifications does the NEC MultiSync EA271Q have?

The NEC MultiSync EA271Q has the following certifications: TCP 7.0.

What is the screen size of the NEC MultiSync EA271Q?

The screen size of the NEC MultiSync EA271Q is 27 ".

What is the screen resolution of the display of the NEC MultiSync EA271Q?

The screen resolution of the NEC MultiSync EA271Q is 2560 x 1440 pixels.

Is the manual of the NEC MultiSync EA271Q available in English?

Yes, the manual of the NEC MultiSync EA271Q is available in English .

Is your question not listed? Ask your question here

No results