NEC MultiSync EA271Q manual

NEC MultiSync EA271Q
6.7 · 1
PDF manual
 · 39 pages
English
manualNEC MultiSync EA271Q
English-13

English

Multiple monitors connection using DisplayPort

You can daisy-chain monitors to each other using the DisplayPort OUT/IN connections on the monitors.
For using connected monitors in MST (multi-stream transport) mode, the setting should be DP OUT MULTISTREAM “AUTO” for
each monitor. Please change the setting for the monitor that connects to the computer last.
If the monitors do not display an image, turn off the monitor connected to the computer then turn it back on.
Configuring the DisplayPort connections may be necessary. Please refer to the table below and change the settings as needed.
OSD (See page 18)
DP OUT MULTISTREAM “CLONE”
Factory setting.
DisplayPort 1.1a setting with:
– SST (single-stream transport).
DP OUT MULTISTREAM “AUTO”
DisplayPort 1.2 setting with:
– SST (single-stream transport) and MST (multi-stream transport).
Depending on the display adapter settings in the operating system for the connected computer, the image may not extend.
Please refer to the user instructions for the computer to change the settings.
NOTE: Use the DisplayPort cables included with the monitors to connect the monitors to each other.
We strongly recommend using the same monitor model for all monitors in the connected daisy-chain.
Remove the cap from the DisplayPort OUT connector on the monitor.
Please contact your display adapter supplier for detailed information.
BIT RATE Maximum number of connectable monitors
MST (multi-stream transport)
HBR2 (Default setting) 2 units (HDCP contents: 2 units)
HBR 1 unit (HDCP contents: 1 unit)
NOTE: The number of monitors that can daisy-chain, from a single connection to the computer, depends on the display
adapter capabilities and its settings.
Please refer to the user instructions for the computer or display adapter.
DisplayPort OUT
DisplayPort IN/OUT
DisplayPort cable
DisplayPort cable
DisplayPort
DisplayPort cable
DisplayPort IN/OUT
DisplayPort IN
NOTE: When the monitor has no image, follow the troubleshooting step Recovering from no image and select
DP VER “1.1” (below).
When set the MST function is selected, the power management function according to the ErP directive doesn’t work.

Recovering from no image

If the monitors do not display an image after configuring DP OUT MULTISTREAM, please follow the instructions below:
1. Turn off the computer.
2. Touch the “MENU” key to show the No Signal OSD menu.
3. Touch the “ ” key to show the VIDEO INPUT menu.
4. Touch “ ” or “ ” to show the DisplayPort switch menu.
5. Select DP VER “1.1” to switch the DisplayPort setting.
6. Touch MENU to close the OSD menu.
7. Turn on the computer.
NOTE: MST (multi-stream transport) and SST (single-stream transport) requires a corresponding display adapter.
Check to make sure that the display adapter supports MST (multi-stream transport).
Please refer to the user instructions for the computer to change the settings.
NOTE: Use the DisplayPort cables included with the monitors to connect the monitors to each other.

Manual

View the manual for the NEC MultiSync EA271Q here, for free. This manual comes under the category monitors and has been rated by 1 people with an average of a 6.7. This manual is available in the following languages: English. Do you have a question about the NEC MultiSync EA271Q or do you need help? Ask your question here

Need help?

Do you have a question about the NEC and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

NEC MultiSync EA271Q specifications

Below you will find the product specifications and the manual specifications of the NEC MultiSync EA271Q.

General
BrandNEC
ModelMultiSync EA271Q | 60004303
Productmonitor
EAN5028695116214
LanguageEnglish
FiletypeUser manual (PDF), Energy label (PDF)
Display
Display diagonal27 "
Display resolution2560 x 1440 pixels
Display brightness (typical)350 cd/m²
Response time6 ms
3DNo
HD typeQuad HD
Display technologyLCD
Panel typePLS
Supported graphics resolutions2560 x 1440
Screen shapeFlat
Pixel pitch0.23 x 0.23 mm
Backlight typeW-LED
Contrast ratio (typical)1000:1
Native aspect ratio16:9
Display number of colors16.78 million colors
Adobe RGB coverage78.3 %
sRGB coverage (typical)100 %
NTSC coverage (typical)74.6 %
Viewable size, horizontal596.74 mm
Viewable size, vertical335.66 mm
Viewing angle, horizontal178 °
Viewing angle, vertical178 °
Horizontal scan range31.5 - 94 kHz
Vertical scan range56 - 75 Hz
DDC/CIYes
Contrast ratio (dynamic)7000:1
Maximum refresh rate60 Hz
TouchscreenNo
Ports & interfaces
Built-in USB hubYes
DisplayPorts quantity2
HDMI ports quantity1
DVI portYes
DVI-D ports quantity1
USB upstream port typeUSB Type-B
USB Type-A downstream ports quantity2
Number of upstream ports1
DisplayPort version1.2
USB Type-C downstream ports quantity1
USB hub version3.2 Gen 1 (3.1 Gen 1)
HDCPYes
VGA (D-Sub) ports quantity0
Power
Power consumption (typical)37 W
Power consumption (PowerSave)0.29 W
Power consumption (max)150 W
AC input voltage100 - 240 V
AC input frequency50 - 60 Hz
Power consumption (standby)- W
E
-
21 kWh
- kWh
Energy efficiency scaleA to G
Weight & dimensions
Bezel width (side)1 mm
Bezel width (bottom)17.7 mm
Bezel width (top)1 mm
Width (without stand)611.8 mm
Depth (without stand)67.2 mm
Height (without stand)361.9 mm
Width (with stand)611.8 mm
Depth (with stand)150 mm
Height (with stand)378 mm
Weight (without stand)5700 g
Weight (with stand)9100 g
Packaging data
Package weight11800 g
Package width730 mm
Package depth217 mm
Package height475 mm
Ergonomics
VESA mountingYes
Panel mounting interface100 x 100 mm
Cable lock slotYes
Height adjustmentYes
Tilt adjustmentYes
SwivelingYes
PivotYes
On Screen Display (OSD)Yes
Plug and PlayYes
Cable lock slot typeKensington
Height adjustment150 mm
Tilt up angle range0 - 35 °
Tilt down angle range0 - 5 °
Pivot angle-90 - 90 °
Swivel angle range0 - 340 °
Other features
On/off switchYes
AC adapter includedYes
TV tuner integratedNo
Operational conditions
Operating temperature (T-T)5 - 35 °C
Storage temperature (T-T)-10 - 60 °C
Operating relative humidity (H-H)20 - 80 %
Storage relative humidity (H-H)10 - 85 %
Operating altitude0 - 5000 m
Non-operating altitude5000 - 12192 m
Sustainability
Sustainability certificatesRoHS, ENERGY STAR
391424
Design
CertificationTCP 7.0
Market positioning-
Product colorBlack
Feet colorBlack
Multimedia
Built-in speaker(s)Yes
Built-in cameraNo
Number of speakers2
RMS rated power2 W
Performance
NVIDIA G-SYNCNo
AMD FreeSyncNo
Logistics data
Harmonized System (HS) code85285210
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the NEC MultiSync EA271Q below.

What screen dimensions does my monitor have?

The size of your monitor is usually expressed in inches, 1 inch is 2.54 centimetres. The size is the diagonal size of your monitor, so you measure the screen from bottom left to top right.

What is HDMI?

HDMI stands for High-Definition Multimedia Interface. An HDMI cable is used to transport audio and video signals between devices.

What certifications does the NEC MultiSync EA271Q have?

The NEC MultiSync EA271Q has the following certifications: TCP 7.0.

What is the screen size of the NEC MultiSync EA271Q?

The screen size of the NEC MultiSync EA271Q is 27 ".

What is the screen resolution of the display of the NEC MultiSync EA271Q?

The screen resolution of the NEC MultiSync EA271Q is 2560 x 1440 pixels.

Is the manual of the NEC MultiSync EA271Q available in English?

Yes, the manual of the NEC MultiSync EA271Q is available in English .

Is your question not listed? Ask your question here

No results