Navilock NL-82052USB manual

Navilock NL-82052USB
9.2 · 1
PDF manual
 · 14 pages
English
manualNavilock NL-82052USB

1. Introduction

The engine modules are serial, USB and TTL GNSS receiver with an internal active antenna.
The GNSS receiving is realized using the u-blox NEO-M8U module. In this module, high-sensitivity
sensors such as a 3D accelerometer and a 3D gyroscope are also integrated. These sensors enable the
acquisition of dynamic three-dimensional motion data. These include speed, acceleration, direction and
inclination. From this data, the engine modules acquires position data that complements the current GNSS
position data. They allow reliable position determination even when the GNSS signal is interrupted in the
case of four-wheeled vehicles.
In order to be able to fully utilize the UDR functionality, the receiver must be firmly and unchangeably
connected to the chassis of the vehicle. At the first commissioning after reaching the 3D Satfix, an
approximately 20 minute trip with a speed of more than 30 km/h has to be completed. The journey can be
completed in normal road traffic with curves and acceleration periods. During this travel, the above-
mentioned sensors values are calibrated fully automatic. During this time, the receiver supplies the normal
GNSS position data. From the time of the successful sensor calibration, the UDR position data is added to
the GNSS position data in the NMEA 4.1 protocol. The UDR data is determined and delivered with an
updating rate of 20 Hz.
Due to the additional UDR position data, the receiver reliably delivers its position immediately after
switching on even in the car park or garage.
If your vehicle is moved without its own force after calibration (towing, ferrying, etc.), the receiver
automatically discards its calibration data. At the next trip meeting the above criteria it will be automatically
recalibrated.

1.1. Contents*

1 x Navilock engine module
1 x 8 cm CD ROM including operation manual
* Before using the device, please make sure that all the parts are included in the package. If any parts are
missing or damaged, please contact your dealer immediately.

Manual

View the manual for the Navilock NL-82052USB here, for free. This manual comes under the category GPS devices and has been rated by 1 people with an average of a 9.2. This manual is available in the following languages: English. Do you have a question about the Navilock NL-82052USB or do you need help? Ask your question here

Need help?

Do you have a question about the Navilock NL-82052USB and the answer is not in the manual? Ask your question here. Provide a clear and comprehensive description of the problem and your question. The better your problem and question is described, the easier it is for other Navilock NL-82052USB owners to provide you with a good answer.

Number of questions: 0

Navilock NL-82052USB specifications

Below you will find the product specifications and the manual specifications of the Navilock NL-82052USB.

General
Brand Navilock
Model NL-82052USB | 62763
Product GPS device
EAN 4043619627639
Language English
Filetype Usermanual (PDF)
GPS Performance
Interface USB
Chipset u-blox NEO-M8U
Frequency 1602.5625 MHz
Navigation signals supported B1,E1,L1
Channels quantity 72 channels
Navigation protocols GGA,GSA,GSV,NMEA 0183,RMC,VTG
Baud rate 115.2 Kbit/s
Update rate 20 Hz
Sensitivity -160 dBmW
Acquisition times - cold 26 s
Acquisition times - hot 1 s
GPS accuracy - position 2.5 m
GPS accuracy - velocity 2 m/s
Ports & interfaces
USB 2.0 ports quantity 1
Technical details
Product colour Multicolour
WAAS capability
Indication
LED indicators Status
Operational conditions
Operating temperature (T-T) -40 - 85 °C
Battery
Input voltage 5 V
Rechargeable -
Weight & dimensions
Depth 30 mm
Width 30 mm
Height 7.9 mm
Weight - g
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Navilock NL-82052USB below.

Is your question not listed? Ask your question here

No results