Navilock NL-501ETTL manual

Navilock NL-501ETTL
6.6 · 1
PDF manual
 · 27 pages
English
manualNavilock NL-501ETTL
Table 2-6 Reset Configuration - Non SiRFLoc Platforms
Hex Description
0x01 Hot Start— All data valid
0x02 Warm Start—Ephemeris cleared
0x03 Warm Start (with Init)—Ephemeris cleared, initialization data loaded
0x04 Cold Start—Clears all data in memory
0x08 Clear Memory—Clears all data in memory and resets the receiver back to

factory defaults

Table 2-7 Reset Configuration - SiRFLoc Specific
Hex Description
0x00 Perform a hot start using internal RAM data. No initialization data is used.
0x01 Use initialization data and begin in start mode. Uncertainties are 5 seconds

time accuracy and 300 km position accuracy. Ephemeris data in SRAM is

used.

0x02 No initialization data is used, ephemeris data is cleared, and warm start

performed using remaining data in RAM.

0x03 Initialization data is used, ephemeris data is cleared, and warm start

performed using remaining data in RAM.

0x04 No initialization data is used. Position, time and ephemeris are cleared and a cold
start is performed.
0x08 No initialization data is used. Internal RAM is cleared and a factory reset is
performed.
2-4 NMEA Reference ManualDecember 2004
2

102—SetDGPSPort

This command is used to control the serial port used to receive RTCM differential

corrections. Differential receivers may output corrections using different

communication parameters. If a DGPS receiver is used that has different

communication parameters, use this command to allow the receiver to correctly decode

the data. When a valid message is received, the parameters are stored in battery-backed

SRAM and the receiver restarts using the saved parameters.

Table 2-8 contains the input values for the following example:

Set DGPS Port to be 9600,8,N,1.

$PSRF102,9600,8,1,0*12

Table 2-8 Set DGPS Port Data Format
Name Example Units Description
Message ID $PSRF102 PSRF102 protocol header
Baud 9600 4800, 9600, 19200, 38400
DataBits 8 8,7
StopBits 1 0,1
Parity 0 0=None, 1=Odd, 2=Even
Checksum *12
<CR> <LF> End of message termination

Manual

View the manual for the Navilock NL-501ETTL here, for free. This manual comes under the category GPS devices and has been rated by 1 people with an average of a 6.6. This manual is available in the following languages: English. Do you have a question about the Navilock NL-501ETTL or do you need help? Ask your question here

Need help?

Do you have a question about the Navilock NL-501ETTL and the answer is not in the manual? Ask your question here. Provide a clear and comprehensive description of the problem and your question. The better your problem and question is described, the easier it is for other Navilock NL-501ETTL owners to provide you with a good answer.

Number of questions: 0

Navilock NL-501ETTL specifications

Below you will find the product specifications and the manual specifications of the Navilock NL-501ETTL.

General
Brand Navilock
Model NL-501ETTL | 60410
Product GPS device
Language English
Filetype Usermanual (PDF)
GPS Performance
Channels quantity 20 channels
Acquisition times - cold 42 s
Acquisition times - warm 38 s
GPS accuracy - position 10 m
GPS accuracy - velocity 0.1 m/s
Acquisition times - hot 1 s
Battery
Battery capacity 70 mAh
Operational conditions
Operating temperature (T-T) -30 - 85 °C
Storage temperature (T-T) -40 - 85 °C
Indication
LED indicators
Technical details
Product colour Green
Weight & dimensions
Width 30 mm
Depth 7.5 mm
Height 30 mm
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Navilock NL-501ETTL below.

Is your question not listed? Ask your question here

No results