Morco F-11 E L manual

Morco F-11 E L
7.1 · 1
PDF manual
 · 23 pages
English
manualMorco F-11 E L

INSTALLATION AND USERS’ MANUAL

F-11 E L

SUPER COMPACT ROOM SEALED WATER HEATER

10.010.649 00

1-10.010.649-ingles:1-10.005.856-ingles 24/03/14 17:41 Página 1

View the manual for the Morco F-11 E L here, for free. This manual comes under the category water heaters & boilers and has been rated by 1 people with an average of a 7.1. This manual is available in the following languages: English. Do you have a question about the Morco F-11 E L or do you need help? Ask your question here

Need help?

Do you have a question about the Morco and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

General
BrandMorco
ModelF-11 E L
Productwater heater & boiler
LanguageEnglish
FiletypeUser manual (PDF)

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Morco F-11 E L below.

What is the ideal room temperature?

Most people find that the ideal room temperature is between 19 and 22 degrees Celsius.

How can I check if the Morco F-11 E L water heater & boiler is certified for installation?

To check if the Morco F-11 E L water heater & boiler is certified for installation, follow these steps: 1. Look for the INSTALLER section in the manual. 2. In this section, find the Certification, Category, and Type information for the Morco F-11 E L water heater & boiler. 3. Check if the water heater & boiler has an EC Type test certificate. The certificate number should be mentioned in the manual. 4. Verify the Category and Type of the water heater & boiler. It should be specified as I2E+, I2h, I3+, or I38/P. 5. Look for the Country of destination information. It should mention the countries where the water heater & boiler is certified for installation. 6. Ensure that the Type of the water heater & boiler is mentioned as C12. 7. Check the Degree of electrical protection, which should be specified as IP-44. 8. Look for any additional symbols or units mentioned specifically for the Morco F-11 E L model. By following these steps and referring to the relevant sections in the manual, you can determine if the Morco F-11 E L water heater & boiler is certified for installation.

What is the recommended gas pressure for the Morco F-11 E L water heater & boiler?

The recommended gas pressure for the Morco F-11 E L water heater & boiler can be found in the Gas Data section of the manual. Here are the steps to determine the recommended gas pressure: 1. Locate the Gas Data section in the manual. 2. Look for the table or information that provides details about the gas pressure. 3. Check for the specific gas types mentioned, such as Natural Gas (G20), Butane (G30), or Propane (G31). 4. Identify the recommended gas pressure for each gas type mentioned. 5. The gas pressure is typically measured in millibars (mbar). 6. Note the recommended gas pressure for the specific gas type you will be using with the water heater & boiler. By following these steps and referring to the Gas Data section of the manual, you can find the recommended gas pressure for the Morco F-11 E L water heater & boiler.

How can I adjust the water flow rate of the Morco F-11 E L water heater & boiler?

To adjust the water flow rate of the Morco F-11 E L water heater & boiler, follow these steps: 1. Locate the User section in the manual. 2. Look for the instructions on selecting the hot water temperature. 3. Find the water temperature dial (usually labeled as "2") on the water heater & boiler. 4. Turn the water temperature dial to adjust the desired temperature. 5. The dial may have markings indicating the temperature range, such as "MIN" for the minimum temperature and "MAX" for the maximum temperature. 6. Increase the water flow rate by turning the water temperature dial towards the "MAX" position. 7. Decrease the water flow rate by turning the water temperature dial towards the "MIN" position. 8. Adjust the water flow rate according to your preference and requirements. By following these steps and referring to the User section of the manual, you can adjust the water flow rate of the Morco F-11 E L water heater & boiler.

What is the maximum absorbed power of the Morco F-11 E L water heater & boiler?

The maximum absorbed power of the Morco F-11 E L water heater & boiler is 35 Watts. This information can be found in the Electrical Data section of the manual.

Is the manual of the Morco F-11 E L available in English?

Yes, the manual of the Morco F-11 E L is available in English .

Is your question not listed? Ask your question here

No results