Montpellier MW6201P manual

Montpellier MW6201P
7.9 · 1
PDF manual
 · 30 pages
English
manualMontpellier MW6201P

EN - 10

The mains cord of your washing machine
is equipped with an earthed plug. This
plug should always be inserted to an
earthed socket of 10 amps.
The plug should always be inserted to a
grounded socket of 10 amperes. The
fuse rating of the plug should also be 10
amperes.
If you do not have a suitable socket and
fuse conforming with this, please ensure
the work is carried out by a qualified
electrician.
We do not take responsibility for
damage that occurs due to the use of
ungrounded equipment.
NOTE:
Operating your machine with
low voltage will cause the life cycle of your
machine to be reduced and its
performance to be restricted.
3.4. Water Inlet Hose Connection
3/4”
10 mm
1
3
2
4
1. Your machine may have either a
single water inlet connection (cold)
or double water inlet connection (hot
and cold) depending on the machine
specifications. The white capped hose
should be connected to cold water
inlet and red capped hose to the hot
water inlet (if applicable).
To prevent water leaks at the joints,
either 1 or 2 nuts (depending on your
machine’s specifications) are supplied in
the packaging with the hose. Fit these
nuts to the end(s) of the water inlet hose
that connect to the water supply.
2.
Connect new water inlet hoses to a ¾ ˝,
threaded tap.
Connect the white capped end of the
water inlet hose to the white water inlet
valve on the rear side of the machine
and the red capped end of the hose to
the red water inlet valve (if applicable).
Hand tighten the connections. If in any
doubt, consult a qualified plumber.
Water flow with pressure of 0.1-1 Mpa
will allow your machine to operate at
optimum efficiency (pressure of 0.1 Mpa
means that more than 8 litres of water
per minute will flow through a fully
opened tap).
3. Once you have made all of the
connections, carefully turn the water
supply on and check for leaks.
4. Ensure that the new water inlet hoses
are not trapped, kinked, twisted, folded
or crushed.
If your machine has a hot water inlet
connection, the temperature of the hot
water supply should not be higher than
70°C.
NOTE:
Your Washing Machine must
only be connected to your water supply
~ 95 cm ~ 140 cm
~ 145 cm ~ 95 cm
0 – max. 100 cm
˜
95cm
˜
150cm

Manual

View the manual for the Montpellier MW6201P here, for free. This manual comes under the category washing machines and has been rated by 1 people with an average of a 7.9. This manual is available in the following languages: English. Do you have a question about the Montpellier MW6201P or do you need help? Ask your question here

Need help?

Do you have a question about the Montpellier and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Montpellier MW6201P specifications

Below you will find the product specifications and the manual specifications of the Montpellier MW6201P.

General
BrandMontpellier
ModelMW6201P
Productwashing machine
LanguageEnglish
FiletypeUser manual (PDF)

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Montpellier MW6201P below.

What temperature should I use for my laundry?

The washing label of your garment shows the recommended washing temperature.

Do I need to use an anti-scaling agent for my washing machine?

It is not necessary to use an anti-scaling agent. Scale deposits can be prevented by limiting washing at high temperatures and using the recommended amount of detergent per wash.

How do I prevent my washing machine from smelling?

Unpleasant odours can be avoided by occasionally washing at 60 degrees and using the recommended amount of detergent per wash.

Is the manual of the Montpellier MW6201P available in English?

Yes, the manual of the Montpellier MW6201P is available in English .

Is your question not listed? Ask your question here

No results