Monitor Audio Monitor 200 manual

Monitor Audio Monitor 200
8.3 · 1
PDF manual
 · 170 pages
English
manualMonitor Audio Monitor 200

MRW-10 Positioning & Initial Set Up

Leave the subwoofer unplugged from the mains until all signal cables are connected
and feet attached.
Fix the feet to the bottom of the MRW-10 using the provided screws into the pilot holes on the base of
the cabinet.
The subwoofer should now be sited in the most suitable position, preferably not directly in the corner of
a room as this may cause excessive bass boom. Once a desirable position is achieved it is important to
check if the cables are long enough to reach comfortably without being under tension. Cables should be
less than 10 metres to avoid interference.
WARNING: Never connect or disconnect the RCA input/ output leads with the
subwoofer switched on.
For initial setting up, put the Power Mode Switch in the ‘On’ position and leave the 12v trigger cable (if
being used) disconnected.
Once the input cables are connected and the power mode switch is in the On position, the subwoofer
can be connected to the mains power supply and switched on at the mains power switch.

MRW-10 Set Up

Connected to an AV Receiver

The majority of AV amplifiers have automatic setup systems. If your amp has an auto set up procedure,
run this now with the volume set to around 10 - 12 o’clock, and the power mode switch in the On
position.
When the auto set up is complete check the settings on the AV amp for the sub woofer to ensure they
are correct. The crossover frequency should be roughly the same as in the table on page 6 and the level
should be no more/ less than +/- 3dB. If not we would suggest adjusting accordingly.
Now play a variety of music/ film excerpts that you are familiar with gradually increasing the volume to an
average listening level once you are sure everything is working correctly.

Connected to a Stereo Amplifier

Stereo L & R input may be required if using a 2-channel stereo amplifier, or an amplifier with no LFE
output. Connect 2 x interconnect cables (left and right) from the amplifier to connections marked L & R.
With the pre/ integrated amplifier set to a low level, set the subwoofer up using the suggested guide
below before playing any music/ test tones.
Set the volume to around 10 o’clock (Page 6)
Frequency should be set in accordance to your main speakers (refer to the table on Page 6)
Phase to 0 (Page 6)
Now play some familiar music and gradually adjust the volume and/ or the frequency until happy with the
integration and balance of the sub woofer with the rest of the system.
Monitor Series8

Manual

View the manual for the Monitor Audio Monitor 200 here, for free. This manual comes under the category speakers and has been rated by 1 people with an average of a 8.3. This manual is available in the following languages: English. Do you have a question about the Monitor Audio Monitor 200 or do you need help? Ask your question here

Index

Need help?

Do you have a question about the Monitor Audio and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Monitor Audio Monitor 200 specifications

Below you will find the product specifications and the manual specifications of the Monitor Audio Monitor 200.

General
BrandMonitor Audio
ModelMonitor 200
Productspeaker
LanguageEnglish
FiletypeUser manual (PDF)

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Monitor Audio Monitor 200 below.

When is my volume too loud?

A volume above 80 decibels can be harmful to hearing. When the volume exceeds 120 decibels, direct damage can even occur. The chance of hearing damage depends on the listening frequency and duration.

Can bluetooth devices of different brands be connected to each other?

Yes, bluetooth is a universal method that allows different devices equipped with bluetooth to connect to each other.

Wat is Dolby Atmos?

Dolby Atmos is a technology that ensures that the sound is reflected from the ceiling to where you are listening. This makes it possible to create a 5.1 effect with only 1 speaker.

What is bluetooth?

Bluetooth is a way of exchanging data wirelessly between electronic devices via radio waves. The distance between the two devices that exchange data can in most cases be no more than ten metres.

Is the manual of the Monitor Audio Monitor 200 available in English?

Yes, the manual of the Monitor Audio Monitor 200 is available in English .

Is your question not listed? Ask your question here

No results