Monacor SPS-20S manual

Monacor SPS-20S
9.1 · 1
PDF manual
 · 2 pages
English
manualMonacor SPS-20S

Stereo-Lautsprecher-

Schaltpult

Bitte lesen Sie diese Anleitung vor dem Be trieb gründlich
durch und heben Sie sie für ein späteres Nach lesen auf.
1 Verwendungsmöglichkeiten
Dieses Lautsprecher-Schaltpult dient zum beliebigen
Ein- bzw. Umschalten von zwei Lautsprecherpaaren
(4–8Ω) an einem Stereo-Verstärkerausgang. Mit
dem Schaltpult lässt sich eine Leis tung von bis zu
200 W
MAX schalten.
2 Wichtige Hinweise für den Gebrauch
G
Verwenden Sie das Gerät nur im Innenbereich und
schützen Sie es vor Tropf- und Spritzwasser, hoher
Luftfeuchtigkeit und Hitze (zulässiger Einsatztempe-
raturbereich 0 40 °C).
G
Verwenden Sie für die Reinigung nur ein trockenes,
weiches Tuch, auf keinen Fall Chemikalien oder
Wasser.
G
Wird das Gerät zweckentfremdet, nicht fachgerecht
angeschlossen oder überlastet, kann keine Haftung
für daraus resultierende Sach- oder Personenschä-
den und keine Garantie für das Gerät übernommen
werden.
3 Inbetriebnahme
1) Ein Lautsprecherpaar mit den Klemmen SP1 ver-
binden und das andere Lautsprecherpaar mit den
Klemmen SP2 (siehe Abb. 1). Dabei auf die richtige
Polung achten, d. h. die gekennzeichnete Ader der
Lautsprecherkabel im mer mit der entsprechenden
roten Klemme verbinden. Außerdem die Stereo-
kanäle nicht vertauschen, d. h. jeweils den linken
Kanal immer mit dem entsprechenden Klemmen-
paar L+ / L
-
verbinden.
Soll das Gerät endgültig aus dem Betrieb ge-
nommen werden, übergeben Sie es zur um-
weltgerechten Entsorgung einem örtlichen
Recyclingbetrieb.
Vorsicht! Niemals 4-Ω-Lautsprecher, auch nicht
über das Schaltpult, an einen Verstärker mit einer
Ausgangsimpedanz von 8 Ω anschließen. Der Ver-
stärker kann beschädigt werden.
2) Die Signalquelle (Verstärker bzw. Receiver) nur
anschließen, wenn diese ausgeschaltet ist! Die
Lautsprecherausgänge der Signalquelle über Laut-
sprecherkabel mit den Klemmen AMP verbinden.
3) Alle angeschlossenen Geräte einschalten.
4) Mit den beiden Schaltern lassen sich die zwei Laut-
sprecherpaare beliebig ein- bzw. umschalten. Sind
beide Lautsprecherpaare eingeschaltet, werden
sie durch das Schaltpult in Reihe geschaltet, so-
dass der angeschlossene Verstärker nicht überlas -
tet wird. Sind beide Lautsprecherpaare ausge-
schaltet, wird der Verstärker durch die eingebauten
220-Ω-Widerstände belastet, sodass ein Leerlauf-
betrieb ausgeschlossen ist.
4 Technische Daten
Schaltleistung: . . . . . . . . . . 200 WMAX
Abmessungen: . . . . . . . . . 176 × 50 × 100 mm
Gewicht: . . . . . . . . . . . . . . 530 g
Änderungen vorbehalten.

Stereo Speaker Switch Box

Please read these operating instructions carefully prior
to operating the speaker and keep them for later use.
1 Applications
This speaker switch box is used to switch on resp.
switch over two speaker pairs (4 8 Ω) to one stereo
amplifier output as desired. The switch box is able to
handle a music power of up to 200 W
MAX.
2 Important Notes
G
The unit is suitable for indoor use only. Protect it
against dripping water and splash water, high air hu-
midity, and heat (admissible ambient temperature
range 0 40 °C).
G
For cleaning only use a dry, soft cloth, never use
chemicals or water.
G
No guarantee claims for the unit and no liability for
any resulting personal damage or material damage
will be accepted if the unit is used for other purposes
than originally intended, if it is not correctly con-
nected, or if it is overloaded.
3 Setting into Operation
1) Connect one speaker pair to the SP1 terminals and
the other speaker pair to the SP2 terminals (see
fig. 1). Observe the correct polarity, i. e. always con-
nect the coded core of the speaker cables to the
corre spond ing red terminal. Furthermore, do not
mix up the stereo channels, i. e. in each case con-
nect the left channel always to the corresponding
terminal pair L+/L
-
.
If the unit is to be put out of operation defini-
tively, take it to a local recycling plant for a
disposal which is not harmful to the environ-
ment.
Caution! Never connect 4 Ω speakers, not even via
the switch box, to an amplifier with an output imped -
ance of 8 Ω. The amplifier may be damaged.
2) Only connect the signal source (amplifier or re-
ceiver) if it is switched off! Connect the speaker out-
puts of the signal source via speaker cables to the
terminals AMP.
3) Switch on all connected units.
4) Both switches can be used to switch on resp.
switch over the two speaker pairs. If both speaker
pairs are switched on, they will be switched in se-
ries by the switch box so that the connected ampli-
fier will not be overloaded. If both speaker pairs are
switched off, the amplifier will be loaded by the in-
stalled 220 Ω resistors so that a no-load condition is
avoided.
4 Specifications
Music power: . . . . . . . . . . . 200 WMAX
Dimensions: . . . . . . . . . . . 176 × 50 × 100 mm
Weight: . . . . . . . . . . . . . . . 530 g
Subject to technical modification.

SPS-20S Best.-Nr. 21.0670

®
MONACOR INTERNATIONAL GmbH & Co. KG • Zum Falsch 36 • 28307 Bremen • Germany
Copyright
©
by MONACOR INTERNATIONAL. All rights reserved. A-1383.99.02.11.2012
®

D A CH
GB

Manual

View the manual for the Monacor SPS-20S here, for free. This manual comes under the category switches and has been rated by 1 people with an average of a 9.1. This manual is available in the following languages: English. Do you have a question about the Monacor SPS-20S or do you need help? Ask your question here

Need help?

Do you have a question about the Monacor and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Monacor SPS-20S specifications

Below you will find the product specifications and the manual specifications of the Monacor SPS-20S.

General
BrandMonacor
ModelSPS-20S | 21.0670
Productswitch
EAN4007754111644
LanguageEnglish
FiletypeUser manual (PDF)
Audio
Audio input channels2 channels
Audio output channels- channels
Technical details
Audio port typeScrew terminal
Control typeLever
Product colorBlack
Housing materialMetal
Weight & dimensions
Width176 mm
Depth100 mm
Height50 mm
Weight430 g
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Monacor SPS-20S below.

What is the weight of the Monacor SPS-20S?

The Monacor SPS-20S has a weight of 430 g.

What is the height of the Monacor SPS-20S?

The Monacor SPS-20S has a height of 50 mm.

What is the width of the Monacor SPS-20S?

The Monacor SPS-20S has a width of 176 mm.

What is the depth of the Monacor SPS-20S?

The Monacor SPS-20S has a depth of 100 mm.

Is the manual of the Monacor SPS-20S available in English?

Yes, the manual of the Monacor SPS-20S is available in English .

Is your question not listed? Ask your question here

No results