Mitsubishi WS-65315 manual

Mitsubishi WS-65315
7.4 · 1
PDF manual
 · 76 pages
English
manualMitsubishi WS-65315
3

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER OR BACK.
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user
of the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be
sufficient magnitude to constitute a risk of electric shock.
The exclamation point within an equilateral triangle is intended to alert the user to the presence
of important operating and maintenance (service) instructions in the literature accompanying the
appliance.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by Mitsubishi could void the user’s authority to
operate this equipment.
This TV is very heavy! Exercise extreme care when moving TV as foreign material may become
embedded in the castor wheels which could damage wood or other delicate flooring.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
NOTE TO CATV SYSTEM INSTALLER:
THIS REMINDER IS PROVIDED TO CALL THE CATV SYSTEM INSTALLER’S ATTENTION TO ARTICLE 820-40 OF THE
NEC THAT PROVIDES GUIDELINES FOR THE PROPER GROUNDING AND, IN PARTICULAR, SPECIFIES THAT THE
CABLE GROUND SHALL BE CONNECTED TO THE GROUNDING SYSTEM OF THE BUILDING, AS CLOSE TO THE
POINT OF CABLE ENTRY AS PRACTICAL.

CAUTION

Warning: To avoid permanently imprinting a fixed image onto your TV screen, please do not display
the same stationary images on the screen for more than 15% of your total TV viewing in one week.
Examples of stationary images are letterbox top/bottom bars from DVDs or other video sources,
side bars when showing standard TV pictures on widescreen TVs, stock market reports, video
game patterns, black or bright Closed Caption backgrounds, station logos, web sites or stationary
computer images. Such patterns can unevenly age the picture tubes causing permanent damage to
the TV. Please see page 6, 12 or 30 for a detailed explanation.
RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION: To assure continued FCC compliance, the user must use a shielded video interface
cable with bonded ferrite cores at both ends, when using the MonitorLink/DVI input.

Manual

View the manual for the Mitsubishi WS-65315 here, for free. This manual comes under the category televisions and has been rated by 1 people with an average of a 7.4. This manual is available in the following languages: English. Do you have a question about the Mitsubishi WS-65315 or do you need help? Ask your question here

Need help?

Do you have a question about the Mitsubishi and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 1
M
Melvyn OligerJanuary 7, 2023

Won't power on

Mitsubishi WS-65315 specifications

Below you will find the product specifications and the manual specifications of the Mitsubishi WS-65315.

General
BrandMitsubishi
ModelWS-65315
Producttelevision
LanguageEnglish
FiletypeUser manual (PDF)

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Mitsubishi WS-65315 below.

What's the best viewing distance for my Mitsubishi television?

The ideal viewing distance for your Mitsubishi television depends on the screen size. As a rule of thumb you can assume that approximately 2.4 times the screen diagonal is the ideal viewing distance.

My television has no signal anymore, now what?

If your television has no signal, you can check the following: - Check whether your television is set to the correct source. - Check if your TV receiver is properly connected via the HDMI or SCART input.

What screen dimensions does my television have?

The size of your television is usually expressed in inches, 1 inch is 2.54 centimetres. The size is the diagonal size of your television, so you measure the screen from bottom left to top right.

What is HDMI?

HDMI stands for High-Definition Multimedia Interface. An HDMI cable is used to transport audio and video signals between devices.

Can bluetooth devices of different brands be connected to each other?

Yes, bluetooth is a universal method that allows different devices equipped with bluetooth to connect to each other.

How do I turn on the Mitsubishi WS-65315 television?

To turn on the Mitsubishi WS-65315 television, follow these steps: 1. Locate the power button on the television. It is usually located on the front or side panel. 2. Press the power button once to turn on the television. 3. Wait for a few seconds for the television to power up. You may see a startup screen or the Mitsubishi logo. 4. If the television does not turn on, check if it is properly plugged into a power outlet and that the outlet is receiving power. 5. If the television still does not turn on, try using the remote control to turn it on. Press the power button on the remote control and wait for the television to respond. 6. If none of the above steps work, refer to the troubleshooting section of the manual or contact Mitsubishi customer support for further assistance. Please note that these steps are general guidelines and may vary slightly depending on the specific model of the Mitsubishi WS-65315 television.

Why is the power button on my Mitsubishi WS-65315 television not working?

If the power button on your Mitsubishi WS-65315 television is not working, you can try the following steps: 1. Check the batteries in the remote control. Make sure they are properly installed and have enough power. If necessary, replace the batteries with new ones. 2. Ensure that there are no obstructions between the remote control and the television. Remove any objects that may be blocking the signal. 3. Clean the remote control. Use a soft, lightly moistened cloth to remove any dirt or debris that may be affecting the button's functionality. 4. Try using the power button on the television itself instead of the remote control. If the power button on the television is also not working, there may be an issue with the internal circuitry or power supply. In this case, it is recommended to contact Mitsubishi customer support for further assistance. Please note that these steps are general troubleshooting suggestions and may not resolve all issues with the power button. For more specific guidance, refer to the troubleshooting section of the manual or contact Mitsubishi customer support.

How do I adjust the volume on the Mitsubishi WS-65315 television?

To adjust the volume on the Mitsubishi WS-65315 television, follow these steps: 1. Locate the volume control buttons on the television or the remote control. The volume control buttons are usually labeled with "+" and "-" symbols. 2. Press the "+" button to increase the volume or the "-" button to decrease the volume. Each press will adjust the volume by a small increment. 3. If you prefer a more precise adjustment, you can access the on-screen menu by pressing the "Menu" button on the remote control. Use the arrow buttons to navigate to the "Audio" or "Sound" settings. 4. Within the "Audio" or "Sound" settings, you may find additional options to adjust the volume, such as a volume slider or numerical values. Use the arrow buttons to select the desired option and press the "Enter" or "OK" button to confirm. 5. Experiment with different volume levels until you find the desired sound level. You can also mute the sound by pressing the "Mute" button on the remote control. Please note that these steps are general guidelines and may vary slightly depending on the specific model of the Mitsubishi WS-65315 television.

Why is there no sound coming from my Mitsubishi WS-65315 television?

If there is no sound coming from your Mitsubishi WS-65315 television, you can try the following steps: 1. Check the volume level on the television. Press the volume up button on the remote control or the volume control buttons on the television to ensure that the volume is not set to the lowest level or muted. 2. Verify that the audio cables are properly connected. Ensure that the audio cables from external devices, such as cable boxes or DVD players, are securely plugged into the corresponding audio input ports on the television. 3. Check the audio settings on the television. Press the "Menu" button on the remote control and navigate to the "Audio" or "Sound" settings. Ensure that the audio settings are configured correctly, such as selecting the appropriate audio input source and adjusting the balance or surround sound settings if necessary. 4. Test the audio with different sources. Try playing audio from different sources, such as switching to a different channel or playing a DVD, to determine if the issue is specific to a particular source or input. 5. If none of the above steps resolve the issue, there may be a problem with the internal speakers or audio circuitry. In this case, it is recommended to contact Mitsubishi customer support for further assistance. Please note that these steps are general troubleshooting suggestions and may not resolve all issues with the sound on the Mitsubishi WS-65315 television.

How do I change the input source on the Mitsubishi WS-65315 television?

To change the input source on the Mitsubishi WS-65315 television, follow these steps: 1. Locate the "Input" or "Source" button on the remote control. It is usually labeled with an icon representing multiple input sources. 2. Press the "Input" or "Source" button to display a list of available input sources on the screen. 3. Use the arrow buttons on the remote control to navigate through the list of input sources. 4. Stop scrolling when the desired input source is highlighted. 5. Press the "Enter" or "OK" button on the remote control to select the highlighted input source. 6. The television will switch to the selected input source, and you should now see the content from that source on the screen. Please note that the available input sources may vary depending on the connected devices and the specific model of the Mitsubishi WS-65315 television.

Why is the video quality poor on my Mitsubishi WS-65315 television?

The video quality on your Mitsubishi WS-65315 television may appear poor due to various factors. Here are some steps you can take to improve the video quality: 1. Adjust the video settings: Access the on-screen menu by pressing the "Menu" button on the remote control. Navigate to the "Video" or "Picture" settings and adjust parameters such as contrast, brightness, sharpness, color, and tint to optimize the picture performance. 2. Check the input source: Ensure that the input source is providing a high-quality video signal. If you are using a cable or satellite connection, verify that the signal strength is sufficient. If using external devices, such as DVD players or gaming consoles, ensure they are connected properly and set to output the appropriate video resolution. 3. Align the TV: Use the convergence menu to properly align the TV if the picture appears blurry or out of focus. This can help improve the overall video quality. 4. Consider the format size: Depending on the content being displayed, you can adjust the format size to match the aspect ratio of the source. Options such as standard, expand, zoom, narrow, stretch, and stretch plus may be available. 5. Reduce video noise: If you notice graininess or minor noise in the picture, you can enable the video noise reduction feature, which operates in 480i mode. Please note that these steps are general recommendations and may not address all possible causes of poor video quality. For more specific guidance, refer to the troubleshooting section of the manual or contact Mitsubishi customer support.

How do I access the main menu screens on the Mitsubishi WS-65315 television?

To access the main menu screens on the Mitsubishi WS-65315 television, follow these steps: 1. Locate the "Menu" button on the remote control. It is usually labeled with the word "Menu" or an icon representing a menu. 2. Press the "Menu" button to display the main menu on the screen. The main menu provides access to various settings and features of the television. 3. Use the arrow buttons on the remote control to navigate through the menu options. The available options may include picture settings, sound settings, channel settings, input settings, and other customization options. 4. Stop scrolling when the desired menu option is highlighted. 5. Press the "Enter" or "OK" button on the remote control to select the highlighted menu option. 6. Within each menu option, you can further navigate and adjust specific settings using the arrow buttons and the "Enter" or "OK" button. 7. To exit the main menu, press the "Menu" button again or use the arrow buttons to navigate to the "Exit" or "Close" option and press the "Enter" or "OK" button. Please note that the specific menu options and layout may vary depending on the model of the Mitsubishi WS-65315 television.

Why can't I find the setup menu on my Mitsubishi WS-65315 television?

If you can't find the setup menu on your Mitsubishi WS-65315 television, you can try the following steps: 1. Press the "Menu" button on the remote control to access the main menu. 2. Use the arrow buttons on the remote control to navigate through the menu options. Look for a category or option that is related to setup or settings. It may be labeled as "Setup," "Settings," or something similar. 3. If you don't see a setup or settings option in the main menu, try navigating to other categories such as "Picture," "Sound," or "System." Sometimes, the setup menu can be found within these categories. 4. If you still can't find the setup menu, it's possible that the menu layout may vary depending on the specific model of the Mitsubishi WS-65315 television. In this case, refer to the troubleshooting section of the manual or contact Mitsubishi customer support for further assistance. Please note that these steps are general guidelines and may not apply exactly to your specific model.

How do I enable captions on the Mitsubishi WS-65315 television?

To enable captions on the Mitsubishi WS-65315 television, follow these steps: 1. Press the "Menu" button on the remote control to access the main menu. 2. Use the arrow buttons on the remote control to navigate to the "CAPTIONS" or "Closed Captions" menu option. This option may be located within the "Audio" or "Settings" category. 3. Press the "Enter" or "OK" button on the remote control to enter the "CAPTIONS" menu. 4. Within the "CAPTIONS" menu, use the arrow buttons to select the desired type of captions, such as "Standard" or "Text." Standard captions follow the dialogue of the characters on-screen, while text captions may contain additional information like weather or news. 5. To choose the background color for the captions, use the arrow buttons to select either "Black" or "Translucent Gray." Mitsubishi recommends using the translucent gray background to prevent CRT aging and burn-in. 6. Once you have made your selections, press the "Enter" or "OK" button to confirm and enable the captions. Please note that the specific menu options and layout may vary depending on the model of the Mitsubishi WS-65315 television.

Why are the captions not displaying properly on my Mitsubishi WS-65315 television?

If the captions are not displaying properly on your Mitsubishi WS-65315 television, you can try the following steps: 1. Access the "CAPTIONS" menu by pressing the "Menu" button on the remote control and navigating to the appropriate menu option. This option may be labeled as "CAPTIONS" or "Closed Captions." 2. Within the "CAPTIONS" menu, check the type of captions that are selected. You can choose between standard closed captions (CC1, CC2, CC3, or CC4) or text closed captions (Text1, Text2, Text3, or Text4). 3. If the captions appear strange or have odd characters, misspellings, or grammar, it is likely that the content of the captions is determined by the broadcaster and not a malfunction of the TV. 4. Check the background color setting for the captions. You can choose between black or translucent gray. Mitsubishi recommends using the translucent gray background to prevent CRT aging and burn-in. Please note that these steps are based on the information found in the manual for the Mitsubishi WS-65315 television. If the issue persists, you may need to refer to the troubleshooting section of the manual or contact Mitsubishi customer support for further assistance.

How do I edit the channel list on the Mitsubishi WS-65315 television?

To edit the channel list on the Mitsubishi WS-65315 television, follow these steps: 1. Press the "Menu" button on the remote control to access the main menu. 2. Use the arrow buttons on the remote control to navigate to the "Channel" or "Channel Edit" menu option. This option may be located within the "Settings" or "Setup" category. 3. Press the "Enter" or "OK" button on the remote control to enter the "Channel Edit" menu. 4. Within the "Channel Edit" menu, you can add or delete channels from memory, name channels, and add channels to the Super Quick View (SQV) list. 5. To add or delete channels, use the arrow buttons to select the desired channel and press the "Enter" or "OK" button. You can also use the Adjust buttons or enter the 3-digit channel number you want to change. 6. To add channels to the SQV list, navigate to the SQV option using the arrow buttons and press the "Enter" or "OK" button. Follow the on-screen instructions to select the desired memory bank and add or delete channels. 7. Once you have made your changes, exit the menu by pressing the "Menu" button again or navigating to the "Exit" or "Close" option and pressing the "Enter" or "OK" button. Please note that the specific menu options and layout may vary depending on the model of the Mitsubishi WS-65315 television.

Why are some channels missing from my Mitsubishi WS-65315 television?

If some channels are missing from your Mitsubishi WS-65315 television, you can try the following steps to troubleshoot the issue: 1. Check the antenna or cable connection: Ensure that the antenna or cable is securely connected to the television. Make sure the cable is not damaged and is properly connected to the antenna input or cable/RF input on the television. 2. Perform a channel scan: Access the "Channel" or "Channel Scan" menu option in the settings. Initiate a channel scan to search for available channels. This will help the television detect and add any missing channels. 3. Check for signal strength: If the missing channels are from an antenna source, check the signal strength. Weak or low-quality signals may result in missing channels. Consider repositioning the antenna or using a signal amplifier to improve the signal strength. 4. Verify channel availability: Some channels may not be available in your area or may require a subscription or additional equipment. Check with your service provider or consult an online channel guide to confirm the availability of the missing channels. 5. Reset the television: If the above steps do not resolve the issue, try resetting the television to its factory settings. This can be done through the "System" or "Reset" menu option in the settings. Note that this will erase any customized settings and preferences. Please note that these steps are general troubleshooting suggestions and may not resolve all cases of missing channels. For more specific guidance, refer to the troubleshooting section of the manual or contact Mitsubishi customer support.

How do I add a favorite channel to the Super Quick View list on the Mitsubishi WS-65315 television?

To add a favorite channel to the Super Quick View (SQV) list on the Mitsubishi WS-65315 television, follow these steps: Using the Menu Screen: 1. Press the "Menu" button on the remote control and navigate to the "Channel Edit" menu option. 2. Select the channel you want to add to the SQV list using the arrow buttons or the CHANNEL button on the remote control. 3. Move the selector to the "On/Off" setting for SQV. 4. Select the SQV memory bank you want to modify. 5. Press the ENTER button to add the current channel to the selected SQV memory bank. Using the Remote Control: 1. Use the CHANNEL or number buttons to select the channel you want to add. 2. Press and hold the SQV button for about 3 seconds. When "SQV" and the memory bank number appear under the channel number, the channel has been successfully added. To change the SQV banks using the remote control: 1. Press the SQV button. 2. Press a number button within 5 seconds of pressing the SQV button to change memory banks. To remove SQV channels using the remote control: 1. Press the SQV button repeatedly until you see the desired channel. 2. While the channel number and SQV indicator are still displayed, press the CANCEL button to remove the channel. Please note that the specific steps may vary slightly depending on the model of the Mitsubishi WS-65315 television.

Why is the Super Quick View list not working on my Mitsubishi WS-65315 television?

If the Super Quick View (SQV) list is not working on your Mitsubishi WS-65315 television, you can try the following steps to troubleshoot the issue: 1. Check the SQV settings: Access the "Channel Edit" or "SQV" menu option in the settings. Ensure that the SQV feature is enabled and that the desired channels are added to the SQV memory banks. 2. Verify the channel availability: Make sure that the channels you have added to the SQV list are currently available and properly tuned. Check the signal strength and ensure that the channels are not experiencing any technical difficulties or outages. 3. Reset the SQV list: If the SQV list is not functioning correctly, you can try resetting it. Access the "Channel Edit" or "SQV" menu option and look for a reset or clear option. Select this option to remove all channels from the SQV list and start fresh. 4. Perform a factory reset: If the above steps do not resolve the issue, you can try performing a factory reset on the television. This will restore all settings to their original defaults. Refer to the "System" or "Reset" menu option in the settings to initiate the factory reset. Please note that these steps are general troubleshooting suggestions and may not resolve all cases of the SQV list not working. For more specific guidance, refer to the troubleshooting section of the manual or contact Mitsubishi customer support.

Is the manual of the Mitsubishi WS-65315 available in English?

Yes, the manual of the Mitsubishi WS-65315 is available in English .

Is your question not listed? Ask your question here

No results