Miele WCR 860 WPS manual

Miele WCR 860 WPS
5.6 · 1
PDF manual
 · 116 pages
English
manualMiele WCR 860 WPS

7.End of programme

41

End of programme

The door remains locked during the

anti-crease phase and Finish/Anti-crease

and Unlock with “Start/Stop” appear in

the display.

Touch the Start/Stopsensor control.

The door will unlock.

The drum lighting will come on.

Tip: The door unlocks automatically at

the end of the anti-crease phase.

Reach under the door grip and pull

the door open.

Remove the laundry.

Items left in the drum could discolour

other items in the next wash or be-

come discoloured themselves.

Remove all items from the drum.

Check the folds in the door seal for

any small articles, e.g. buttons, which

might be lodged there.

Tip: Leave the door slightly open to al-

low the drum to dry.

Switch the washing machine off with

the control.

If applicable, remove the used cap-

sule from the detergent dispensing

drawer.

Tip: Leave the detergent dispenser

drawer slightly open to allow it to dry.

Manual

View the manual for the Miele WCR 860 WPS here, for free. This manual comes under the category washing machines and has been rated by 1 people with an average of a 5.6. This manual is available in the following languages: English. Do you have a question about the Miele WCR 860 WPS or do you need help? Ask your question here

Index

Need help?

Do you have a question about the Miele and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Miele WCR 860 WPS specifications

Below you will find the product specifications and the manual specifications of the Miele WCR 860 WPS.

The Miele WCR 860 WPS is a washing machine with a rated capacity of 9 kg, making it suitable for medium to large-sized laundry loads. The spin noise level is measured at 68 dB and the wash noise level at 46 dB, ensuring a relatively quiet operation. With an energy consumption of 0.74 kWh per cycle, the Miele WCR 860 WPS is energy-efficient. Even when not in use, the standby and off power consumptions are both measured at 0.3 W, minimizing energy waste. The cycle time for this washing machine can reach a maximum of 199 minutes, allowing for thorough and effective cleaning. It has a maximum spin speed of 1600 RPM, resulting in a drier load which reduces drying time. The Miele WCR 860 WPS features a built-in display, providing clear and intuitive control options. The door hinge is located on the right side for convenient access. It also offers a rinse hold function, which allows for temporary pause during the wash cycle. Control of the machine is done through buttons and touch input, ensuring ease of use. Additionally, a delayed start timer is included, enabling users to schedule their laundry according to their preferences. Overall, the Miele WCR 860 WPS is a reliable and efficient washing machine that offers a generous load capacity and various convenient features. Its energy-saving design, low noise levels, and user-friendly controls make it a practical choice for households looking to efficiently tackle their laundry needs.

General
BrandMiele
ModelWCR 860 WPS | 10931210
Productwashing machine
EAN4002516024279
LanguageEnglish
FiletypeUser manual (PDF), Warranty information (PDF), Datasheet (PDF), Energy label (PDF)
Design
Product colorWhite
Built-in displayYes
Door hingeRight
Control typeButtons, Touch
Tub materialStainless steel
Cord length2 m
Loading typeFront-load
Appliance placementFreestanding
Door colorSilver
Inverter technologyNo
Performance
Drum capacity9 kg
Noise level (spin)68 dB
Noise level (wash)46 dB
Cycle time (max)199 min
Maximum spin speed1600 RPM
Residual moisture44 %
Rinse holdYes
Delayed start timerYes
Delay start (max)24 h
Foam control systemYes
Black, Blouse/shirt, Cold, Cotton, Easy care, Hand, Wool, Intensive/outdoor, Jeans/denim, Pillow, Quick, Sport, Delicate/silk
Rinse Plus functionYes
Wi-Fi controlledYes
Overflow protectionYes
Number of washing programs-
Spin-drying classA
TimerYes
A
Power
Energy consumption washing per cycle0.74 kWh
Power consumption (standby)0.3 W
Power consumption (off)0.3 W
Water consumption per cycle48 L
Connected load2400 W
AC input voltage220 - 240 V
AC input frequency50 Hz
Current10 A
Energy efficiency classA
Energy efficiency scaleA to G
49 kWh
Ergonomics
Remaining time indicationYes
Drum interior lightYes
Self-cleaningYes
Self-cleaning detergent drawerYes
BuzzerYes
Child lockYes
Automatic dosing systemYes
Dosage assistantYes
Weight & dimensions
Width596 mm
Depth636 mm
Height850 mm
Weight96000 g
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Miele WCR 860 WPS below.

What temperature should I use for my laundry?

The washing label of your garment shows the recommended washing temperature.

Do I need to use an anti-scaling agent for my washing machine?

It is not necessary to use an anti-scaling agent. Scale deposits can be prevented by limiting washing at high temperatures and using the recommended amount of detergent per wash.

How do I prevent my washing machine from smelling?

Unpleasant odours can be avoided by occasionally washing at 60 degrees and using the recommended amount of detergent per wash.

What is the weight of the Miele WCR 860 WPS?

The Miele WCR 860 WPS has a weight of 96000 g.

What is the height of the Miele WCR 860 WPS?

The Miele WCR 860 WPS has a height of 850 mm.

What is the width of the Miele WCR 860 WPS?

The Miele WCR 860 WPS has a width of 596 mm.

What is the depth of the Miele WCR 860 WPS?

The Miele WCR 860 WPS has a depth of 636 mm.

What energy label does the Miele WCR 860 WPS have?

The Miele WCR 860 WPS has energy label A.

Does the Miele WCR 860 WPS have a built-in display?

Yes, the Miele WCR 860 WPS has a built-in display.

What is the maximum spin speed of the Miele WCR 860 WPS?

The maximum spin speed of the Miele WCR 860 WPS is 1600 RPM. This is considered high and can effectively remove excess water from the laundry, resulting in faster drying times.

Does the Miele WCR 860 WPS have a rinse hold feature?

Yes, the Miele WCR 860 WPS has a rinse hold feature. This allows the user to pause the wash cycle to soak the laundry or add additional items before rinsing.

What is the energy consumption per cycle of the Miele WCR 860 WPS?

The energy consumption per cycle of the Miele WCR 860 WPS is 0.74 kWh. This is relatively low and indicates energy-efficient operation, helping to reduce electricity costs.

Can the Miele WCR 860 WPS be started with a delay?

Yes, the Miele WCR 860 WPS has a delayed start timer with a maximum delay of 24 hours. This allows users to set the machine to start at a specific time, providing flexibility and convenience in managing their laundry.

How can I troubleshoot if the programme sequence of the Miele WCR 860 WPS washing machine is not working correctly?

If the programme sequence of the Miele WCR 860 WPS washing machine is not working correctly, you can troubleshoot the issue by following these steps: 1. Check the power supply: Ensure that the mains plug is properly plugged in and switched on. Also, check if the fuse or circuit breaker has tripped. 2. Reset the machine: If the display remains dark and the Start/Stop button indicator light does not come on, the washing machine may have switched off automatically to save energy. Press the power button to switch it back on. If prompted, enter any required code and confirm the entry. 3. Verify the door lock: If the display shows a message indicating that the door will not lock, make sure that the door is closed properly. Close the door again and start the programme once more. If the fault message persists, contact Miele for further assistance. 4. Changing the programme sequence: If you need to change the programme, temperature, spin speed, or selected options, remember that these cannot be modified once the machine has started. However, you can interrupt a programme by switching off the washing machine and then switch it back on to continue with the same programme. To cancel a programme, touch the Start/Stop sensor and select "Yes" when prompted. The programme will be cancelled, and you can remove the laundry and select a new programme if needed. By following these troubleshooting steps, you should be able to address any issues with the programme sequence of the Miele WCR 860 WPS washing machine.

What should I do if the PowerWash feature of the Miele WCR 860 WPS washing machine is not providing energy-saving benefits?

If the PowerWash feature of the Miele WCR 860 WPS washing machine is not providing energy-saving benefits, you can take the following steps to troubleshoot the issue: 1. Check the selected programme: Ensure that you have selected one of the programmes in which the PowerWash feature is activated. These programmes include Cottons, ECO 40-60, Minimum iron, Shirts, Automatic plus, Delicates, and Cottons with small and medium load sizes. 2. Verify the conditions for PowerWash activation: Make sure that the selected final spin speed is not less than 600 rpm, CapDosing has not been selected for the main wash, the wash temperature is not higher than 60°C, and no extras such as Pre-wash or Water plus have been selected. Also, ensure that you are not washing a large load in the Cottons programme. 3. Optimize load size: Load the maximum dry load size recommended for the wash programme you are using. This will help maximize energy and water efficiency. 4. Consider programme running time: Keep in mind that programmes that are more efficient in terms of energy and water consumption may have a longer running time. By extending the programme running time, the wash temperature can be reduced while still achieving the same wash results. 5. Use lower temperature settings: Take advantage of modern detergents that allow washing at lower temperatures, such as 20°C. Using lower temperature settings can help save energy. By following these steps, you should be able to troubleshoot and optimize the energy-saving benefits of the PowerWash feature in the Miele WCR 860 WPS washing machine.

How can I troubleshoot if the PowerWash feature of the Miele WCR 860 WPS washing machine is not activating or deactivating properly in different programs?

To troubleshoot if the PowerWash feature of the Miele WCR 860 WPS washing machine is not activating or deactivating properly in different programs, you can follow these steps: 1. Check the selected program: Ensure that you have chosen one of the programs in which the PowerWash feature is automatically activated. These programs include Cottons (with small and medium load sizes), ECO 40-60 (with small and medium load sizes), Minimum iron, Shirts, Automatic plus, Delicates, and Cottons with small and medium load sizes. 2. Verify the conditions for PowerWash activation: Make sure that the selected final spin speed is not less than 600 rpm, CapDosing has not been selected for the main wash, the wash temperature is not higher than 60°C, extras such as Pre-wash or Water plus have not been selected, and you are not washing a large load in the Cottons program. 3. Reset the machine: If the PowerWash feature is still not activating or deactivating properly, try resetting the washing machine. Switch it off, unplug it from the power source, wait for a few minutes, and then plug it back in and switch it on again. 4. Contact Miele for assistance: If the issue persists after following the above steps, it is recommended to contact Miele customer support for further troubleshooting and assistance. By following these steps, you should be able to troubleshoot any issues related to the activation or deactivation of the PowerWash feature in the Miele WCR 860 WPS washing machine.

What should I do if the drenching phase of the Miele WCR 860 WPS washing machine is not functioning as expected?

If the drenching phase of the Miele WCR 860 WPS washing machine is not functioning as expected, you can try the following steps to troubleshoot the issue: 1. Check the detergent: Ensure that you are using the recommended detergent for the drenching phase. Liquid detergents may not be effective in removing certain stains, so it is recommended to use the Miele 2 Phase System or a general-purpose powder detergent containing a bleaching agent. 2. Remove white residues: If you notice white residues resembling powder detergent on dark textiles after washing, these may be caused by compounds (zeolites) in the detergent that are not soluble in water. Try brushing off the residues with a soft brush once the laundry is dry. Alternatively, you can wash dark textiles using a detergent that does not contain zeolites. 3. Address grey, greasy particles: If grey, greasy particles cling to washed laundry, it may indicate insufficient amounts of detergent used to break down the particles of grease in heavily soiled laundry. Use more detergent to ensure effective cleaning. If the issue persists after following these steps, it is recommended to refer to the Miele WCR 860 WPS washing machine's manual or contact Miele customer support for further assistance.

How can I troubleshoot if there are unusual noises during the heating phase of the Miele WCR 860 WPS washing machine?

To troubleshoot unusual noises during the heating phase of the Miele WCR 860 WPS washing machine, you can follow these steps: 1. Check for excessive foam: Excessive foam can cause unusual noises during the heating phase. Ensure that the correct amount of detergent is being dispensed. If using automatic detergent dispensing, check the dosage amount set. Follow the instructions on the detergent packaging and adjust the dispensing quantity if necessary. 2. Run a maintenance wash: If a wash program with a temperature above 60°C has not been run for a long time, it can lead to bacteria buildup and unpleasant odors. Run the Clean machine program using Miele machine cleaner or a universal powder detergent to maintain hygiene. 3. Confirm fault messages: If fault messages appear at the end of the program or when the washing machine is switched on, they need to be confirmed with the OK sensor. Follow the instructions provided in the manual to address any specific fault messages. If the issue persists or if you encounter any other unusual noises during the heating phase, it is recommended to contact Miele customer support for further assistance.

Is the manual of the Miele WCR 860 WPS available in English?

Yes, the manual of the Miele WCR 860 WPS is available in English .

Is your question not listed? Ask your question here

No results