MicroView MVIB-04IR-E manual

MicroView MVIB-04IR-E
7.2 · 1
PDF manual
 · 171 pages
English
manualMicroView MVIB-04IR-E
Network Camera User Manual
111
3. Select a region number from the drop-down list of Region.
Region: A pre-defined vertexes area on the live view image. Targets, such as,
people, vehicle or other objects, who enter and loiter in the region will be detected
and trigger the set alarm.
4. Click Area Settings tab and click Draw Area button to start the region drawing.
5. Click on the live video to specify the four vertexes of the detection region, and right
click to complete drawing.
6. Set the Max. Size and Min. Size for valid targets. Targets smaller or larger than the
valid target size are not able to trigger detection.
Max. Size: The maximum size of a valid target. Targets with larger sizes would
not trigger detection.
Min. Size: The minimum size of a valid target. Targets with smaller sizes would
not trigger detection.
7. Click Stop Drawing when finish drawing.
8. Set the time threshold for intrusion detection.
Threshold: Range [0s-10s], the threshold for the time of the object loitering in the
region. If you set the value as 0, alarm is triggered immediately after the object
entering the region.
9. Drag the slider to set the sensitivity value.
Sensitivity: Range [1-100]. Sensitivity stands for the percentage of the body part
of an acceptable target that enters the pre-defined region.
Sensitivity = 100 – S
1
/S
T
*100
S
1
stands for the target body part that goes across the pre-defined region. S
T
stands
for the complete target body.
Example: if you set the value as 60, the action can be counted as an intrusion only
when 40 percent body part enters the region.
Note: The Sensitivity of the detection is supported by certain models. Refer to
actual display for details.
10. Repeat the above steps to configure other regions. Up to 4 regions can be set. You

Manual

View the manual for the MicroView MVIB-04IR-E here, for free. This manual comes under the category security cameras and has been rated by 1 people with an average of a 7.2. This manual is available in the following languages: English. Do you have a question about the MicroView MVIB-04IR-E or do you need help? Ask your question here

Index

Need help?

Do you have a question about the MicroView and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

MicroView MVIB-04IR-E specifications

Below you will find the product specifications and the manual specifications of the MicroView MVIB-04IR-E.

General
BrandMicroView
ModelMVIB-04IR-E | MVIB-04IR-E
Productsecurity camera
EAN5711783978695
LanguageEnglish
FiletypeUser manual (PDF)
Video
Total megapixels4 MP
Maximum resolution2560 x 1440 pixels
Frame rate30 fps
Video streamingYes
3D NR (Noise Reduction)Yes
Video formats supportedH.264, H.264+, H.265, H.265+, M-JPEG
Bit rate32 Kbps - 8 Mbps
Supported graphics resolutions320 x 240,352 x 240,352 x 288,640 x 360,640 x 480 (VGA),1920 x 1080 (HD 1080),2304 x 1296,2560 x 1440
Image quality adjustmentBrightness, Contrast, Saturation, Sharpness
Full HDYes
Privacy maskingYes
Image sensor
Sensor typeCMOS
Number of sensors1
Optical sensor size1/3 "
Progressive scanYes
Network
Streaming methodMulticast
Quality of Service (QoS) supportYes
Supported network protocolsTCP/IP, ICMP, HTTP, HTTPS, FTP, DHCP, DNS, DDNS, RTP, RTSP, RTCP, PPPoE, NTP, UPnP, SMTP, SNMP, IGMP, 802.1X, QoS, IPv6, Bonjour
Ethernet LANYes
Ethernet interface typeFast Ethernet
Wi-FiNo
BluetoothNo
Networking standardsIEEE 802.3at
Lens system
Focal length range2.8 - 12 mm
Auto focusYes
Maximum aperture number1.6
Number of lenses1
Power
Power source typeDC, PoE
Power consumption (typical)7.5 W
Design
International Protection (IP) codeIP67
IK codeIK10
WeatherproofYes
Protection featuresVandal proof
Product colorBlack, White
Form factorBullet
Mounting typeCeiling/wall
Night vision
Night visionYes
Night vision distance50 m
LED typeIR
Infra-red wavelength850 nm
Performance
Wide Dynamic Range (WDR)Yes
Infrared (IR) cut-off filterYes
Day/night modeYes
TypeIP security camera
Placement supportedOutdoor
Connectivity technologyWired
Alarm input/outputYes
Camera
Minimum illumination0.018 lx
51 °
92 °
115 °
Pan range0 - 360 °
Angle of rotation360 °
Tilt angle range0 - 90 °
Audio
Audio formats supportedG.711, G.726
Storage
Card reader integratedYes
Built-in HDD-
Compatible memory cardsMicroSD (TransFlash), MicroSDHC, MicroSDXC
Maximum memory card size128 GB
Management features
Behavior analysisIntrusion detection, Line crossing detection
Web browserYes
Reset buttonYes
Security
Video motion detectionYes
Anti-flickerYes
HeartbeatYes
MirrorYes
Password protectionYes
IP address filteringYes
Other features
Number of simultaneous users32 user(s)
Packaging content
Number of cameras1
Ports & interfaces
Ethernet LAN (RJ-45) ports1
Microphone inYes
BNC output ports1
Terminal block portYes
Operational conditions
Operating temperature (T-T)-30 - 60 °C
Weight & dimensions
Diameter144.1 mm
Depth332.7 mm
Weight1740 g
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the MicroView MVIB-04IR-E below.

What is the weight of the MicroView MVIB-04IR-E?

The MicroView MVIB-04IR-E has a weight of 1740 g.

What is a megapixel?

The number of megapixels denotes how many pixels there are in the sensor. 1 megapixel equals 1 million pixels. The more pixels, the higher the potential image quality.

What does the abbreviation 'MP' stand for?

MP stands for MegaPixels.

What is the depth of the MicroView MVIB-04IR-E?

The MicroView MVIB-04IR-E has a depth of 332.7 mm.

Is the manual of the MicroView MVIB-04IR-E available in English?

Yes, the manual of the MicroView MVIB-04IR-E is available in English .

Is your question not listed? Ask your question here

No results