Medisana MediTouch 2 manual

Medisana MediTouch 2
8 · 20
PDF manual
 · 4 pages
English
manualMedisana MediTouch 2

DE Kontrolllösung

zur Eigenan-

wendung

Art. 79039 Stand: 11/2014

Zeichenerklärung

Gebrauchsanweisung

Diese Gebrauchsanweisung gehört zu dieser Blutzuckerkontroll-
lösung. Sie enthält wichtige Informationen zum Gebrauch. Lesen
Sie diese Gebrauchsanweisung vollständig. Die Nichtbeachtung
dieser Anweisung kann zu schweren Verletzungen oder Schäden
führen. G
G
G
Schreiben Sie das Öffnungsdatum auf das Etikett des Behälters. Die
Kontrolllösung bleibt von der Öffnung des Behälters an ca. drei
Monate oder bis zum Verfallsdatum verwendbar, je nach dem, was
zuerst zutrifft. i
Verwenden Sie die Kontrolllösung nicht über das Verfallsdatum
hinaus. i
Die Umgebungstemperatur bei Gebrauch der Kontrolllösung darf
zwischen 10 °C - 40 °C (50 °F - 104 °F) liegen. G
Die maximalen Temperaturwerte für Aufbewahrung und Transport
der Kontrolllösung liegen zwischen 2°C und 30°C (35.6°F 86°F).
Bewahren Sie die Lösung nicht im Kühlschrank auf und frieren Sie
sie nicht ein. G
Schütteln Sie die Flasche mit der Testlösung gut, bevor Sie sie
öffnen. G
Wischen Sie den ersten Tropfen mit einem sauberen Tuch ab und
verwenden Sie den zweiten, um eine gute Probe für genaue Mess-
ergebnisse zu erhalten. G
Damit die Kontrolllösung nicht verunreinigt wird, wischen Sie
Lösungsreste mit einem sauberen Tuch von der Spitze des Be-
hälters, bevor Sie diesen wieder verschließen. G
Medizinische „In vitro“- Diagnose-Kontrolllösung (nur zur
äußeren Anwendung) G
Kontrolllösung G
LOT-Nummer G
Produkt-Nummer G
Lagertemperaturbereich G
Hersteller G
Verfallsdatum 3 Monate nach Öffnung entsorgen
Diese Blutzuckerkontrolllösung entspricht den Anforderungen
der EG-Richtlinie 98/79 für “In Vitro” Diagnostika und ist mit
dem CE-Zeichen (Konformitätszeichen) CE 0483“versehen.
MEDISANA AG
Jagenbergstraße 19
41468 NEUSS
Deutschland
eMail: info@medisana.de
Internet: www.medisana.de

Zweckbestimmung

Die Kontrolllösung für Meditouch 2 von MEDISANA, Art. 79039 dient
der Kontrolle des Blutzuckermessgerätes und der Teststreifen. Sie ist
zur Eigenanwendung bestimmt. Die Anwendung erfolgt äußerlich (in
vitro) unter der Verwendung der Teststreifen und des Messgerätes
Meditouch 2. g
Die Kontrolllösung entspricht der Richtlinie 98/79/EG nach Anhang IV.3
für In Vitro Diagnostika. Die Konformität mit der o.g. Richtlinie wurde
durch die Firma mdc Medical devices certification GmbH bestätigt.
MEDISANA Servicecenter
c/o GSL mbH
Am Weimarer Berg 6
99510 Apolda
Bestell-Hotline: 01803 00 33 90
Service-Hotline: 01805 45 40 15
eMail: Blutzucker-info@medisana.de
(für allgemeine Informationen)
Blutzucker-shop@medisana.de
(für Nachbestellungen von Zubehör)
Internet: www.meditouch.de
Bestellhotline: 9 ct/Minute aus dem deutschen Netz
Mobilfunk Höchstpreis 42 ct/Minute.
Servicehotline: 14 ct/Minute aus dem deutschen Netz
Mobilfunk Höchstpreis 42 ct/Minute.

Testergebnisse

3
Wurden Kontrolllösung oder Teststreifen nach Ablauf Ihres Verfall-
datums benutzt oder wurde die Kontrolllösung verunreinigt?
Wurden Kontrolllösung oder Teststreifen nicht korrekt verschlossen
aufbewahrt?
Wurden die in den Gebrauchsanweisungen zur Kontrolllösung, Art.
79039, den Teststreifen (Art. 79038 / 79040) und dem Gerät (Art.
79030 / 79034) beschriebenen Punkte zur korrekten Testdurchführung
beachtet?
Wiederholen Sie den Test anweisungsgemäß mit einwandfreier
Kontrolllösung und einwandfreien Teststreifen. Treten noch immer
Werte außerhalb der auf dem Teststreifenbehälter angegebenen
Grenzwerte auf, kontaktieren Sie bitte die Servicestelle.
Befinden sich die Testergebnisse mit Kontrolllösung innerhalb der auf
dem Teststreifenbehälter angegebenen Grenzwerte, arbeiten Test-
streifen und Messgerät korrekt zusammen. Die Messergebnisse Ihrer
Blutzuckermessung werden verlässlich sein. g
Befinden sich die Testergebnisse mit Kontrolllösung außerhalb der auf
dem Teststreifenbehälter angegebenen Grenzwerte, arbeitet das
System nicht korrekt. Prüfen Sie in diesem Fall die folgenden Punkte:

WARNHINWEISE

Die Kontrolllösung für Meditouch 2 von MEDISANA ist nur für den
äußerlichen Gebrauch (in vitro) geeignet!
Die Kontrolllösung ist NICHT für den Verzehr oder als Injektion
geeignet!
Benutzen Sie die MEDISANA-Kontrolllösung nur zusammen mit den
MediTouch 2-Teststreifen und dem MediTouch 2- Messgerät!
Frieren Sie die Kontrolllösung NICHT ein!

Chemische Bestandteile

Die Kontrolllösung für Meditouch 2 von MEDISANA enthält folgende
Reagenzien:
0,12 Gew. % D-Glucose
99,88 Gew. % Nichtreaktive Bestandteile
Im Servicefall wenden Sie sich bitte an:
Murrays Health & Beauty
School Lane
Chandlers Ford
Hampshire
UK SO534YN
Tel. +44/2380460600
email: cservices@paulmurrayplc.co.uk
Internet: www.meditouch.co.uk

GB Control solution

for self-testing

Explanation of symbols

Instructions for use

This instruction manual is for this blood glucose control solution. It
contains important information about starting up and operation.
Read the instruction manual thoroughly. Non-observance of these
instructions can result in serious injury or damage to the device.
Write the opening date on the label of the container. The control
solution can be used for approx. three months after opening the
container or until the expiry date, whichever comes first. i
Do not use the control solution after the expiry date. G
The ambient temperature for using the control solution should lie
between 10 °C - 40 °C (50 °F - 104 °F). G
The temperatures for storing and transporting the control solution
should lie between min 2 °C and max 30 °C (35.6 °F 86 °F). Do
not store the solution in the refrigerator and do not freeze it. G
Shake the bottle with the control solution well before you open it. G
Wipe away the first drop with a clean cloth and use the second drop
to ensure you get a good sample for a precise reading. G
To ensure the control solution does not get contaminated, wipe the
remaining solution on the tip of the container with a clean cloth before
closing it again. i
The control solution may stain your clothing. If this is the case, rinse
the soiled clothing immediately in water and detergent. G
Do not put any excess control solution back into the container. G
Close the container carefully after every use.
Control solution for medical in vitro diagnosis (for external
use only) G
Control solution G
LOT number G
Catalogue number G
Storage temperature limitation G
Manufacturer G
Use by Discard 3 months after opening
This blood glucose control solution corresponds to the re-
quirements of the EU guidelines 98/79 for in vitro diagnostics
and bears the CE marking (conformance label) CE 0483.

Intended purpose

The control solution Meditouch 2 from MEDISANA, art. 79039 is suffi-
cient for the examination of the blood glucose measurement device and
the test strips. It is intended for self-testing. The control solution is for
external (in vitro) use only, together with the teststrips and the measure-
ment device Meditouch 2. g
The control solution corresponds to the direction 98/79/EC, attachment
IV.3 for in vitro diagnostics. The conformity with the above mentioned
direction has been confirmed by company mdc Medical devices
certification GmbH.
3

PRECAUTIONS

The control solution for Meditouch 2 from MEDISANA is only
intended for the external (in vitro) diagnostic use!
The control solution is NOT suitable for consumption or injection!
Only use the MEDISANA control solution for testing with the Medi-
Touch 2 test strips and the MediTouch 2 device!
Do NOT freeze the control solution!
Art. 79039 Effective: 11/2014
MEDISANA AG
Jagenbergstraße 19
41468 NEUSS
Germany
eMail: info@medisana.de
Internet: www.medisana.com

Test results

Have the control solution or test strips been used after their expiration
date? Has the control solution been contaminated?
Did you forget to replace the cap on the vial of control solution or test
strips?
Did you follow the instructions for control solution, art. 79039, test-
strips (art. 79038 / 79040) and device (art. 79030 / 79034) thoroughly
to achieve a correct test procedure?
Repeat the test according to the instructions given with proper
control solution and test strips. If the reading is still not acceptable,
contact the service centre.
If the reading of your test falls within the expected range printed on the
test strips vial label, then the test strip and the glucose meter are
working together correctly. The results of your blood glucose tests will
be reliable. g
If the reading falls outside the expected range, your meter may not be
working properly. In this case, check the following:

Chemical Substances

The control solution for Meditouch 2 from MEDISANA contains the
following reagent:
0.12 (w/w) D-Glucose
99.88 (w/w) Non-reactive ingredients
Service centre:
Die Kontrolllösung kann auf Kleidung Flecken verursachen.
Waschen Sie ggf. die verunreinigten Textilien sofort mit Wasser und
Seife aus. G
Überschüssige Kontrolllösung nicht zurück in den Behälter geben.
Schließen Sie den Behälter nach jedem Gebrauch sorgfältig.

View the manual for the Medisana MediTouch 2 here, for free. This manual comes under the category blood glucose meters and has been rated by 20 people with an average of a 8. This manual is available in the following languages: English. Do you have a question about the Medisana MediTouch 2 or do you need help? Ask your question here

Need help?

Do you have a question about the Medisana and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 2
F
FLONTA GABRIEL DRAGOSSeptember 6, 2020

I recently got the device and on the first test it showed 4.5, can you tell me if it's good or bad?

This message has been automatically translated
A
AnnaMay 2, 2019

What is considered a normal fasting blood sugar level when measured with this device, Medisana MediTouch 2?

This message has been automatically translated

The Medisana MediTouch 2 blood glucose meter is a compact device designed to accurately measure blood glucose levels in the human body. With a measurement time of just 5 seconds, it provides quick results for users. The glucose measuring units are displayed in the widely used mmol/L format, ensuring compatibility with most healthcare systems. The device comes equipped with a memory function, allowing users to easily track and monitor their glucose levels over time. It can store up to 480 records, providing ample storage for frequent users. The LED display provides clear and easy-to-read results, ensuring no confusion or misinterpretation. For those who wish to further analyze their data, the MediTouch 2 can be connected to a PC, allowing for seamless data transfer and analysis. It supports two batteries for its operation, ensuring a reliable power source. With a width of 50 millimeters, depth of 10 millimeters, and height of 98 millimeters, the MediTouch 2 is compact and portable. It also comes with a carrying case, enabling users to conveniently and safely transport the device wherever they go. Additionally, the package includes test strips, ensuring that users have all the necessary components to begin testing their blood glucose levels. Overall, the Medisana MediTouch 2 blood glucose meter is a reliable and user-friendly device that provides quick and accurate blood glucose measurements. Its memory function, LED display, and compatibility with PC make it a versatile tool for individuals seeking to monitor their blood glucose levels effectively.

General
BrandMedisana
ModelMediTouch 2 | 79034
Productblood glucose meter
EAN4015588790348
LanguageEnglish
FiletypeUser manual (PDF)
Technical details
Measurement time5 s
Glucose measuring unitsmmol/L
Memory functionYes
Number of memory records480
DisplayLED
Connection to PCYes
Product colorWhite
Battery
Number of batteries supported2
Weight & dimensions
Width50 mm
Depth10 mm
Height98 mm
Packaging content
Carrying caseYes
Test stripsYes
show more

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Medisana MediTouch 2 below.

What is the height of the Medisana MediTouch 2?

The Medisana MediTouch 2 has a height of 98 mm.

What is the width of the Medisana MediTouch 2?

The Medisana MediTouch 2 has a width of 50 mm.

What is the depth of the Medisana MediTouch 2?

The Medisana MediTouch 2 has a depth of 10 mm.

How do I set the date and time on the Medisana MediTouch 2 blood glucose meter?

To set the date and time on the Medisana MediTouch 2, navigate to the settings menu by pressing the designated button. Then, select the "Date & Time" option and use the navigation buttons to input the correct date and time.

How can I change the measurement unit from mg/dL to mmol/L on the Medisana MediTouch 2?

To change the measurement unit from mg/dL to mmol/L on the Medisana MediTouch 2, go to the settings menu and select the "Measurement Unit" option. From there, you can toggle between mg/dL and mmol/L and choose your preferred unit.

When should I perform a control solution test and how do I do it with the Medisana MediTouch 2?

It is important to perform a control solution test with the Medisana MediTouch 2 whenever you open a new vial of test strips, suspect the meter is malfunctioning, or your test results seem inaccurate. To do a control solution test, place a droplet of control solution on a clean test strip and insert it into the meter. The result should fall within the predetermined range specified by the control solution.

Can I transfer my blood glucose data from the Medisana MediTouch 2 to a computer or smartphone?

Yes, you can transfer your blood glucose data from the Medisana MediTouch 2 to a computer or smartphone. The meter is equipped with a USB port for connecting to a computer, and it also supports Bluetooth connectivity for wireless data transfer to compatible smartphones or devices. Follow the instructions provided by the manufacturer for the specific transfer method you prefer.

How often should I calibrate the Medisana MediTouch 2 blood glucose meter?

It is recommended to calibrate the Medisana MediTouch 2 meter with a control solution each time you open a new vial of test strips or if you suspect the meter is giving inaccurate readings. Additionally, it is advisable to perform regular calibration as instructed by your healthcare professional based on your specific needs and circumstances.

Does Medisana MediTouch 2 have a measurement time of 5 seconds?

Yes, Medisana MediTouch 2 has a measurement time of 5 seconds. This means that users can obtain glucose readings quickly and efficiently.

Does Medisana MediTouch 2 use mmol/L as the glucose measuring unit?

Yes, Medisana MediTouch 2 uses mmol/L as the glucose measuring unit. This is a common unit used in blood glucose monitoring devices and allows for easy comparison and interpretation of results.

Does Medisana MediTouch 2 have a memory function?

Yes, Medisana MediTouch 2 has a memory function. This allows users to store and track their glucose readings over time, helping them to monitor their blood sugar levels effectively.

How many memory records does Medisana MediTouch 2 support?

Medisana MediTouch 2 supports up to 480 memory records. This ample storage capacity allows users to store a significant amount of glucose readings, enabling them to track their glucose levels over an extended period.

Does Medisana MediTouch 2 have a LED display?

Yes, Medisana MediTouch 2 has a LED display. LED displays are known for their clarity and visibility, providing users with clear and easy-to-read glucose readings.

Is the manual of the Medisana MediTouch 2 available in English?

Yes, the manual of the Medisana MediTouch 2 is available in English .

Is your question not listed? Ask your question here

No results