Medi1One CMS50D manual

Medi1One CMS50D
7.7 · 6
PDF manual
 · 48 pages
English
manualMedi1One CMS50D

Gebrauchsinformation

Finger-Pulsoximeter

Typ: CMS50D | PZN: 09777842 | REF: CMS50D
EN: Instructions for use
Fingertip Pulse Oximeter

View the manual for the Medi1One CMS50D here, for free. This manual comes under the category heart rate monitor and has been rated by 6 people with an average of a 7.7. This manual is available in the following languages: English. Do you have a question about the Medi1One CMS50D or do you need help? Ask your question here

Need help?

Do you have a question about the Medi1One and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

General
BrandMedi1One
ModelCMS50D
Productheart rate monitor
LanguageEnglish
FiletypeUser manual (PDF)

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Medi1One CMS50D below.

How much should I exercise as an adult per week?

As an adult, it is recommended to do moderately intensive exercise for at least 2.5 hours per week. Preferably spread over several days.

How high is an adult's heart rate at rest?

An adult's resting heart rate is between 60 and 100 beats per minute.

What is an adult's maximum heart rate?

As a rule of thumb for your maximum heart rate, you can use 220 minus your age.

How do I change the display mode on the Medi1One CMS50D heart rate monitor?

To change the display mode on the Medi1One CMS50D heart rate monitor, follow these steps: 1. Put your finger in the correct position on the monitor. 2. Press the switch button once on the front panel. 3. Keep your finger steady and the patient at ease during the process. Avoid any movement. 4. The information will be displayed directly on the screen. 5. The switch button has two functions. If the device is powered off, pressing the button will turn it on. If the device is already powered on, pressing and holding the button will adjust the brightness of the screen. 6. In the working state, the display direction can change automatically based on the device's gradient direction. 7. Ensure that your fingernails and the luminescent tube are on the same side. If you encounter any issues, such as the device not turning on or the display suddenly turning off, try the following solutions: - If the device cannot be turned on, check if the batteries are drained or not inserted properly. Replace or reinstall the batteries accordingly. - If the display turns off suddenly, it is normal for the device to power off automatically when it receives no signal within 5 seconds. However, if the batteries are almost drained, replace them. Please note that these instructions are specific to the Medi1One CMS50D heart rate monitor and may not apply to other models or brands.

What should I do if the heart rate monitor does not turn on with the recommended batteries?

If the heart rate monitor does not turn on with the recommended batteries, you can try the following steps: 1. Check if the batteries are drained or almost drained. If they are, replace them with new ones. 2. Ensure that the batteries are inserted properly. Sometimes, improper insertion can prevent the device from turning on. Reinstall the batteries if necessary. 3. If you have followed the above steps and the heart rate monitor still does not turn on, it may indicate a malfunction in the device. In such cases, it is recommended to contact the local service center for further assistance. Please note that these steps are specific to the Medi1One CMS50D heart rate monitor and may not apply to other models or brands.

Why does the heart rate monitor automatically power off even when I am using it?

The heart rate monitor automatically powers off even when you are using it due to the following reasons: 1. The device will power off automatically when it receives no signal within 5 seconds. This is a normal function to conserve battery life and prevent unnecessary power consumption. 2. If the batteries are almost drained, the device may also power off suddenly. In this case, it is recommended to replace the batteries with new ones. To summarize, the automatic power off feature is designed to save battery power and ensure efficient operation of the heart rate monitor. If the device powers off unexpectedly, check the battery level and replace them if necessary. Please note that these steps are specific to the Medi1One CMS50D heart rate monitor and may not apply to other models or brands.

Can I use the Medi1One CMS50D heart rate monitor for continuous patient supervision?

No, the Medi1One CMS50D heart rate monitor is not intended for continuous patient supervision. The manual states the following precautions and restrictions: 1. The device should not be used ceaselessly, especially for patients with microcirculation barriers, as it may cause discomfort or pain. It is recommended not to apply the sensor to the same finger for more than 2 hours. 2. The device should not be clipped on edema and tender tissue during the placing process. 3. The light emitted from the device, although invisible, is harmful to the eyes. Users should avoid staring at the light. 4. Testees should not use enamel or other makeup, and their fingernails should not be too long. 5. The manual advises users to read the relevant content about clinical restrictions and caution. 6. It is important to note that the device is not intended for treatment. These precautions and restrictions indicate that the Medi1One CMS50D heart rate monitor is not suitable for continuous patient supervision.

What should I do if the heart rate monitor is not functioning properly in high humidity conditions?

To address the issue of the heart rate monitor not functioning properly in high humidity conditions, follow these steps: 1. Ensure that the surface of the device is clean before use. Wipe the device with medical alcohol and let it dry in the air or clean it with a dry clean fabric. 2. After each use, disinfect the product with medical alcohol to prevent cross-infection for the next use. 3. If the heart rate monitor is not in use for a long time, it is recommended to take out the batteries. 4. The best storage environment for the device is an ambient temperature between -40°C and 60°C, with a relative humidity not exceeding 95%. It is important to keep the device in a dry environment, as high humidity may reduce its useful life or cause damage. Please note that these steps are specific to the Medi1One CMS50D heart rate monitor and may not apply to other models or brands.

What should I do if the measured heart rate value on the Medi1One CMS50D heart rate monitor is consistently too high or too low?

If the measured heart rate value on the Medi1One CMS50D heart rate monitor is consistently too high or too low, you can follow these steps to troubleshoot the issue: 1. Ensure proper finger placement: Make sure that you are positioning your finger correctly on the device. Place your finger deep enough inside the device to ensure accurate readings. 2. Check for finger movement: Avoid shaking your finger or moving excessively while using the heart rate monitor. Any movement can affect the accuracy of the readings. Try to keep your finger still during the measurement. 3. Verify the patient's condition: If the measured heart rate value is consistently too low, it could be due to a low SpO2 level that cannot be detected by the device. In such cases, it is recommended to visit a hospital for a proper diagnosis. 4. Repeat the measurement: If you suspect that the initial measurement was incorrect, you can try taking the measurement again. Ensure that you follow the proper finger placement and minimize any movement during the measurement. By following these steps, you can troubleshoot the issue of consistently high or low heart rate values on the Medi1One CMS50D heart rate monitor.

How can I troubleshoot abnormal conditions appearing on the screen during the test process with the Medi1One CMS50D heart rate monitor?

To troubleshoot abnormal conditions appearing on the screen during the test process with the Medi1One CMS50D heart rate monitor, you can follow these steps: 1. Ensure proper finger placement: Make sure that you position your finger properly on the device. Place your finger deep enough inside the device to ensure accurate readings. 2. Minimize finger movement: Avoid shaking your finger or moving excessively while using the heart rate monitor. Any movement can affect the stability of the displayed SpO2 and pulse rate values. 3. Keep the patient calm: It is important to keep the patient calm and at ease during the measurement process. Movement or restlessness can lead to unstable readings. 4. Check for low SpO2 levels: If the SpO2 and pulse rate values cannot be displayed normally, it could be due to a low SpO2 level that is below the detection threshold of the device. In such cases, it is recommended to visit a hospital for a proper diagnosis. 5. Follow the device instructions: Press the switch button once on the front panel to start the measurement process. Avoid pressing the button for a long time, as it is used to change the screen brightness when the device is powered on. By following these steps, you can troubleshoot abnormal conditions appearing on the screen during the test process with the Medi1One CMS50D heart rate monitor.

How often do I need to replace the batteries in the Medi1One CMS50D heart rate monitor, and what should I do if the device is not functioning properly due to low battery?

To answer your question about battery replacement for the Medi1One CMS50D heart rate monitor, please follow these steps: 1. Check the battery level: If the device is not functioning properly, it could be due to low battery power. Check the battery level indicator on the screen to determine if the batteries need to be replaced. 2. Open the battery compartment: Locate the battery compartment on the back of the device. Refer to the instructions for use or the manual for the exact location. 3. Remove the old batteries: Take out the old batteries from the compartment. Make sure to dispose of them properly according to local regulations. 4. Insert new batteries: Insert two AAA size batteries into the compartment, following the correct polarity (+/-) indicated inside the compartment. 5. Close the battery compartment: Securely close the battery compartment to ensure proper functioning of the device. If the device still does not function properly after replacing the batteries, please contact the local service center for further assistance. Please note that the information provided is based on the Medi1One CMS50D heart rate monitor manual and is intended as a general guide.

What should I do if I experience any allergic reactions or sensitivity to the hanging rope of the Medi1One CMS50D heart rate monitor?

If you experience any allergic reactions or sensitivity to the hanging rope of the Medi1One CMS50D heart rate monitor, you can follow these steps: 1. Stop using the hanging rope: If you are sensitive to the hanging rope material, it is recommended to stop using it. Discontinue wearing the hanging rope around your neck to avoid any potential harm. 2. Seek alternative options: If you still need to use the heart rate monitor, consider using an alternative method to secure the device. You can explore options such as using a wristband or a different type of strap that is made from a material that you are not allergic to. 3. Contact customer support: If you require further assistance or have specific concerns about allergies or sensitivity, it is advisable to contact the customer support of Medi1One. They can provide guidance and potential solutions based on your individual needs. Please note that the information provided is based on the Medi1One CMS50D heart rate monitor manual and is intended as a general guide.

Can the Medi1One CMS50D heart rate monitor provide alarms for abnormal parameters, and what should I do if I need an alarm function for specific conditions?

The Medi1One CMS50D heart rate monitor does not have an alarm function for abnormal parameters. If you need an alarm function for specific conditions, you should not rely on this device. It is advised not to use the device in situations where alarms are required. Please note that the information provided is based on the manual for the Medi1One CMS50D heart rate monitor and is intended as a general guide.

Is the manual of the Medi1One CMS50D available in English?

Yes, the manual of the Medi1One CMS50D is available in English .

Is your question not listed? Ask your question here

No results