Maytag MVW6200KW manual

Maytag MVW6200KW
9.1 · 14
PDF manual
 · 132 pages
English
manualMaytag MVW6200KW

À L’USAGE EXCLUSIF DU TECHNICIEN DE MAINTENANCE

NE PAS ENLEVER OU DÉTRUIRE60

CODE D’ANOMALIES ET D’ERREURS

Les anomalies marquées d’un « ‡ » arrêteront l’exécution du programme. Le délai du mode est atteint dans les 5 à 10 minutes, l’écran s’éteint.
Toutes les anomalies peuvent être affichées dans la section « Fault History » (historique des anomalies) du mode d’entretien.

Code Description Explications et procédures recommandées

F0E2 Excès de mousse
L’anomalie est affichée lorsque de la mousse empêche le panier de tourner à grande vitesse ou lorsque le
capteur de pression détecte que le niveau de mousse augmente. La commande principale vidangera l’eau pour
essayer de se débarrasser de la mousse. Si la vidange de l’eau ne peut pas résoudre le problème, il peut s’agir
d’une des raisons suivantes :
dz Utilisation d’un détergent non HE.
dz Utilisation excessive de détergent.
dz Vérifier le raccord du tuyau sous pression entre la cuve et la commande principale. Le tuyau est-il plié, pincé,
bouché ou laisse-t-il fuir de l’air?
dz Friction mécanique sur le mécanisme d’entraînement ou le panier (articles entre le panier et la cuve).
F0E3 Surcharge
L’anomalie est affichée lorsque le module de contrôle principal détecte une charge qui dépasse la capacité de la
laveuse OU lorsque la rotation du panier n’est pas possible. Les raisons de cette anomalie peuvent être les suivantes :
dz La taille de la charge dépasse la capacité de la laveuse. Retirer le surplus de linge, puis redémarrer le programme.
dz Friction mécanique sur le mécanisme d’entraînement ou le panier (articles entre le panier et la cuve).
F0E4
Essorage limité par la
température de l’eau
L’anomalie est affichée lorsque l’eau est trop chaude pour que l’essorage ait lieu à la vitesse de rotation finale.
La vitesse est alors limitée à 500 T/MIN.
dz Vérifier le fonctionnement de la vanne d’arrivée d’eau. Voir le TEST N° 2 : Vannes.
F0E5 Charge déséquilibrée
L’anomalie est sauvegardée lorsqu’un déséquilibre est détecté.
dz Vérifier s’il y a une suspension faible. Le panier ne doit pas rebondir plus d’une fois après l’avoir poussé.
dz Les articles doivent être uniformément répartis lors du chargement.
F0E7
Charge détectée pendant
l’utilisation du programme
Clean Washer (Nettoyage
de la laveuse)
L’anomalie est affichée lorsque des vêtements sont détectés dans le panier alors que le programme Clean
Washer (nettoyage de la laveuse) est sélectionné.
dz Retirer toute charge du panier avant de lancer le programme Clean Washer (nettoyage de la laveuse).
F0E8 Anneau d’eau
L’anomalie est affichée lorsqu’il reste trop d’eau résiduelle.
dz Lancer un programme de vidange et d’essorage.
F0E9 OB Pause
L’anomalie est affichée lorsqu’un état de déséquilibre est détecté et après une intervention de l’utilisateur.
dz Vérifier s’il y a une suspension faible. Le panier ne doit pas rebondir plus d’une fois après l’avoir poussé.
dz Les articles doivent être uniformément répartis lors du chargement.
F1E1
Défaillance du module de
commande principale (MCA)
L’anomalie est affichée pour indiquer qu’il y a une défaillance avec le module de commande principale (MCA).
dz Voir le TEST N° 1 : Module de commande principale (MCA).
F2E1 Bouton IHM coincé
L’anomalie est sauvegardée et indique que l’interface utilisateur a détecté un bouton enfoncé en permanence.
dz Voir le TEST N° 4 : IHM.
F2E2 IHM déconnectée
L’anomalie est affichée si l’IHM est déconnectée du MCA.
dz Voir le TEST N° 4 : IHM.
F3E2
Anomalie du capteur de
pression
L’anomalie est affichée lorsque le module de commande principal détecte un signal de pression hors plage ou absent.
dz Vérifier le raccord du tuyau sous pression entre la cuve et la commande principale. Le tuyau est-il plié, pincé,
bouché ou laisse-t-il fuir de l’air?
dz Voir le TEST N° 6 : Niveau d’eau.
F3E3
Anomalie de température de
l’arrivée d’eau
L’anomalie est sauvegardée lorsque la thermistance d’entrée est détectée de valeur ouverte ou court-circuité.
dz Voir le TEST N° 5 : Thermistance de température.
F5E1
Anomalie du contacteur de
couvercle – le couvercle est
ouvert
Cette anomalie s’affiche si le couvercle est en état verrouillé, mais que le contacteur de porte est ouvert;
la commande ne détecte pas la gâche lors du verrouillage du couvercle.
dz L’utilisateur appuie sur START (mise en marche) lorsque le couvercle est ouvert.
dz La commande principale ne détecte pas correctement l’ouverture et la fermeture du contacteur de couvercle.
dz Voir le TEST N° 8 : Verrouillage du couvercle.

View the manual for the Maytag MVW6200KW here, for free. This manual comes under the category washing machines and has been rated by 14 people with an average of a 9.1. This manual is available in the following languages: English. Do you have a question about the Maytag MVW6200KW or do you need help? Ask your question here

Need help?

Do you have a question about the Maytag and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 216
A
Annetta SmallJune 10, 2024

how many gallons of water for one load? What is the range of gallons of water for the different cycles?

P
Patrick Mahoney June 2, 2024

My Maytag washer mvw6200kw2 starts preliminary spin doesn’t fill than goes to drain in done cycle

B
Beverly MasoveroJuly 21, 2021

If washer load not level how can I shift load without starting cycle all over again? Model mvw6200kw1

If washer load not level how can I shift load without starting cycle all over again? Model mvw6200kw1
zoom-in
View photo
N
Nancy KeysonOctober 10, 2021

I will be having this washer delivered in a week. I see that reviews are stating problems with draining. I had this problem with a Midea that was only 2 weeks old. Is there a pump filter that the consumer can clean?

I will be having this washer delivered in a week. I see that reviews are stating problems with draining. I had this problem w...
zoom-in
View photo
S
SandraOctober 23, 2021

Done 2 loads. My new washer works until it gets to the rinse/spin cycle. At this point, the tub spins constantly with intermittent spurts of water, never filling to rinse the load. It then continues to spin. I eventually had to stop the cycle using the power button. Anyone? Thanks. Translation: I have completed 2 loads of laundry. My new washing machine works well until it reaches the rinse/spin cycle. At this point, the tub keeps spinning continuously with occasional bursts of water, but it never fills up to rinse the load. After that, it continues to spin without progressing. Eventually, I had to stop the cycle by using the power button. Does anyone have any solutions? Thank you.

Done 2 loads. My new washer works until it gets to the rinse/spin cycle. At this point, the tub spins constantly with intermi...
zoom-in
View photo
This message has been automatically translated
K
Kristen Seymour December 10, 2022

I would like to turn the chime on for when the washer had finished a cycle but they're are no buttons for this? Recently bought a house that came with this washer MVW6200k*

I would like to turn the chime on for when the washer had finished a cycle but they're are no buttons for this? Recently boug...
zoom-in
View photo
A
ArinJune 26, 2023

I put a refresh cleaning tablet in the washer and put the washer on clean washer setting and it ran water for a few seconds then drained and now it’s not doing anything but the lid lock light and the three lights at the top of the screen just keep flashing

I put a refresh cleaning tablet in the washer and put the washer on clean washer setting and it ran water for a few seconds t...
zoom-in
View photo
N
Nicole December 26, 2023

Is the soap tray supposed to open on its own at the end of a wash cycle? Mine does this a lot.

Is the soap tray supposed to open on its own at the end of a wash cycle? Mine does this a lot.
zoom-in
View photo
N
NatJanuary 27, 2021

6200 KW washer. Does the machine sense the amount of load of clothes to determine level of water released into the washing drum?

C
Caitlin WerthFebruary 25, 2021

How do you know when a load is complete? Right now the machine has been flashing 'sense' and 'done' alternately but the lid is still locked. Will it stay solid on 'done' when it is done? Also, how long do loads usually take? Ours seems to take hours. We ate concerned we might be doing something wrong.

1 comment
C
Charlotte ThomasApril 30, 2021

Have you solve that problem? I have same problem now and just bought this washer.

The Maytag MVW6200KW is a washing machine designed to provide efficient and reliable laundry care. It is equipped with a variety of features to enhance the washing experience. With a sizable capacity, this washing machine can accommodate large loads of laundry, making it suitable for households with heavy laundry needs. It utilizes advanced cleaning technology to effectively remove dirt and stains from clothes, ensuring thorough cleaning results. The MVW6200KW features multiple wash cycles and options, allowing users to customize their laundry settings according to their specific needs. This includes options for different fabric types and levels of soiling, enabling gentle care for delicate garments and more intensive cleaning for heavily soiled items. The washing machine is designed with an intuitive control panel that makes it easy to navigate and select the desired settings. It also offers a range of convenient features, such as a delay start option that allows users to set a specific time for the wash cycle to begin. In terms of efficiency, the MVW6200KW is built to conserve water and energy, helping to reduce utility costs and environmental impact. It operates quietly, minimizing disturbances while the machine is running. Constructed with durable materials, this washing machine is built to withstand regular use and provide long-term reliability. It is designed to function smoothly and efficiently, ensuring optimal performance over time. Overall, the Maytag MVW6200KW is a dependable and efficient washing machine that offers a range of features to simplify laundry care and deliver satisfactory cleaning results.

General
BrandMaytag
ModelMVW6200KW
Productwashing machine
EAN883049583211
LanguageEnglish
FiletypeUser manual (PDF), Quickstart Guide (PDF), Warranty information (PDF), Safety instructions (PDF), Energy label (PDF)

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Maytag MVW6200KW below.

What temperature should I use for my laundry?

The washing label of your garment shows the recommended washing temperature.

Do I need to use an anti-scaling agent for my washing machine?

It is not necessary to use an anti-scaling agent. Scale deposits can be prevented by limiting washing at high temperatures and using the recommended amount of detergent per wash.

How do I prevent my washing machine from smelling?

Unpleasant odours can be avoided by occasionally washing at 60 degrees and using the recommended amount of detergent per wash.

Why is my washing machine not turning on?

Make sure the machine is plugged into a working electrical outlet and that the circuit breaker has not tripped. Additionally, check if the washer's door is securely closed, as the machine will not operate if the door is open or not properly latched.

Why is my laundry coming out still wet?

Ensure that the selected cycle and settings match your laundry load. If using a high-efficiency detergent, make sure it is appropriate for your type of load. Check if the drain hose is properly connected and not kinked. Adjust the spin speed if necessary, as a slower speed may leave clothes damp.

Why does my washer make excessive noise during operation?

Verify that the unit is level and stable on the floor. Ensure that the load is balanced inside the drum, as unbalanced loads can cause increased noise. Additionally, check if any foreign objects, such as coins or buttons, are trapped inside the tub or pump, as they can contribute to the noise.

How can I clean the washing machine drum?

Run a cleaning cycle with a washing machine cleaner specifically designed to remove dirt and residue. Alternatively, you can wipe the drum interior using a mixture of mild detergent and water, making sure to rinse thoroughly afterward. Avoid using abrasive cleaners or bleach, as they may damage the drum.

Why is my washer displaying error codes?

Different error codes indicate specific issues. To troubleshoot, try turning off the washer and unplugging it for a few minutes before restarting. If the error persists, consult the user manual for a list of error codes and their corresponding solutions. You can also contact customer support for further assistance.

Is the manual of the Maytag MVW6200KW available in English?

Yes, the manual of the Maytag MVW6200KW is available in English .

Is your question not listed? Ask your question here

No results