Maytag MVW6200KW manual

Maytag MVW6200KW
9.1 · 14
PDF manual
 · 132 pages
English
manualMaytag MVW6200KW

À L’USAGE EXCLUSIF DU TECHNICIEN DE MAINTENANCE

NE PAS ENLEVER OU DÉTRUIRE54

GUIDE D’ENTRETIEN

Avant d’entreprendre un travail de réparation, vérifier ce qui suit :
Ƀ
Vérifier que la prise de courant est alimentée.
Ƀ
Un fusible est-il grillé ou le disjoncteur s’est-il déclenché? Un fusible
ordinaire a-t-il été utilisé? Informer le client qu’un fusible temporisé est
nécessaire.
Ƀ
Les robinets d’eau froide et chaude sont-ils ouverts et les tuyaux sont-
ils dégagés?
Ƀ
S’assurer que le tuyau d’évacuation n’est pas scellé dans le tuyau de
vidange et qu’il y a une ouverture pour l’aération. S’assurer que la hauteur
du drain se situe entre 39 po (991 mm) et 8 pi (2,4 m) au-dessus du sol.
Ƀ
Utiliser pour tous les contrôles/tests un multimètre (VOM) ou un
voltmètre numérique (DVM) dont la résistance interne est de 20 000 Ω
par V CC ou plus.
Ƀ
Lors de toute mesure de résistance, vérifier que la laveuse est
débranchée de la prise de courant, ou que la source de courant
électrique est déconnectée.
IMPORTANT : Éviter d’utiliser des sondes de grand diamètre lors du
contrôle des connecteurs des conducteurs, car ces sondes pourraient
endommager les connecteurs lors de l’insertion.
Ƀ
Contrôler la qualité de tous les conducteurs et de toutes les connexions
avant de remplacer des composants. Chercher des connecteurs qui
ne sont pas complètement insérés, qui sont cassés ou qui sont lâches
et des bornes ou des fils qui ne sont pas assez enfoncés dans les
connecteurs pour avoir un bon contact avec les broches métalliques.
Ƀ
La corrosion ou la contamination des pièces de connexion est une
cause potentielle d’anomalie de fonctionnement des organes de
commande. Utiliser un ohmmètre pour vérifier la continuité à travers
les connexions suspectées.
Ƀ
Pour vérifier correctement la tension :
1. Débrancher l’appareil ou déconnecter la source de courant électrique.
2. Fixer les sondes de mesure de la tension aux bons connecteurs.
3. Brancher l’appareil ou reconnecter la source de courant électrique
et vérifier la tension.
4. Débrancher l’appareil ou déconnecter la source de courant
électrique après avoir effectué la mesure de tension.

DEL DE DIAGNOSTIC – Module de commande principal (MCA)

Un utilitaire de dépannage a été mis au point sur la carte de commande
principale, sous la forme d’un témoin DEL de diagnostic.
DEL QUI CLIGNOTE – Le module de commande détecte l’arrivée d’un
courant de ligne correct et le processeur est opérationnel.
DEL ALLUMÉE ou ÉTEINTE – Mauvais fonctionnement de la commande.
Exécuter le TEST nº 1 : Module de commande principal (MCA), pour
vérifier le fonctionnement du module de commande principal.
Illustration 1 – DEL de diagnostic

MODE D’ENTRETIEN

Ces tests permettent au personnel de l’usine et au personnel de service
de tester et de vérifier tous les signaux d’entrée parvenant à la carte de
commande principale. Ces tests permettent l’exécution d’un contrôle
global et rapide de la laveuse avant le passage à des tests de dépannage
spécifiques.

ACTIVATION DU MODE D’ENTRETIEN

1. S’assurer que la laveuse est en mode de veille (branchée avec
toutes les DEL désactivées).
2. Effectuer les étapes suivantes en moins de 8 secondes :
dz Enfoncer et relâcher la touche 1
dz Enfoncer et relâcher la touche 2
dz Enfoncer et relâcher la touche 3
dz Répéter cette séquence de 3 boutons 2 autres fois
3. Si l’accès à ce mode de test est réussi, tous les indicateurs de
l’IHM seront allumés pendant 1 seconde puis s’éteindront. Après
cela, s’il n’y a pas de codes d’erreur enregistrés, les indicateurs
d’ÉTAT (Sense [détection], Soak [trempage], Wash [lavage] et Done
[terminé]) clignoteront deux fois, puis tous les témoins s’éteindront.
DEL groupe 2
DEL groupe 5
DEL groupe 6
DEL
groupe 1
DEL
groupe 3
DEL groupe 4
Touche 6/
ALIMENTA-
TION
Touche 5/
MISE EN
MARCHE
Touche 4
Touche 3
Touche 2
Touche 1
Figure 2 : Schéma de l’écran IHM et des boutons de navigation.
Échec de l’activation
Se référer aux instructions suivantes en cas d’échec de la tentative de
passage au mode de diagnostic :
Indication : Aucune DEL allumée.
Solution : Mettre l’appareil en marche en appuyant sur la touche
POWER (alimentation) ou en tournant le bouton et sélectionner
n’importe quel programme.
Si les DEL s’allument après avoir appuyé sur le bouton POWER
(alimentation) ou après avoir tourné le bouton, essayer à nouveau
de passer en mode Entretien: répéter l’étape 2 mentionnée dans
la séquence d’activation et la terminer dans les 8 secondes qui
suivent. Si ces procédures de rentrée ne parviennent pas à entrer
en mode Diagnostic, il y a probablement un bouton défectueux dans
l’IHM. Remplacer l’IHM.
Si aucune DEL ne s’allume après la sélection du programme, passer
au TEST N° 1 : Module de commande principale (MCA).
Activation en utilisant les codes d’anomalie enregistrés
S’il y a un code d’anomalie enregistré, il clignotera sur l’afficheur. Passer
en revue les codes d’anomalie/erreur du tableau de la page 60 pour voir
la procédure recommandée. S’il n’y a pas de code d’erreur enregistré.
Toutes les DEL s’éteignent.
Emplacement
des DEL
Indicateur
d’état

View the manual for the Maytag MVW6200KW here, for free. This manual comes under the category washing machines and has been rated by 14 people with an average of a 9.1. This manual is available in the following languages: English. Do you have a question about the Maytag MVW6200KW or do you need help? Ask your question here

Need help?

Do you have a question about the Maytag and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 216
A
Annetta SmallJune 10, 2024

how many gallons of water for one load? What is the range of gallons of water for the different cycles?

P
Patrick Mahoney June 2, 2024

My Maytag washer mvw6200kw2 starts preliminary spin doesn’t fill than goes to drain in done cycle

B
Beverly MasoveroJuly 21, 2021

If washer load not level how can I shift load without starting cycle all over again? Model mvw6200kw1

If washer load not level how can I shift load without starting cycle all over again? Model mvw6200kw1
zoom-in
View photo
N
Nancy KeysonOctober 10, 2021

I will be having this washer delivered in a week. I see that reviews are stating problems with draining. I had this problem with a Midea that was only 2 weeks old. Is there a pump filter that the consumer can clean?

I will be having this washer delivered in a week. I see that reviews are stating problems with draining. I had this problem w...
zoom-in
View photo
S
SandraOctober 23, 2021

Done 2 loads. My new washer works until it gets to the rinse/spin cycle. At this point, the tub spins constantly with intermittent spurts of water, never filling to rinse the load. It then continues to spin. I eventually had to stop the cycle using the power button. Anyone? Thanks. Translation: I have completed 2 loads of laundry. My new washing machine works well until it reaches the rinse/spin cycle. At this point, the tub keeps spinning continuously with occasional bursts of water, but it never fills up to rinse the load. After that, it continues to spin without progressing. Eventually, I had to stop the cycle by using the power button. Does anyone have any solutions? Thank you.

Done 2 loads. My new washer works until it gets to the rinse/spin cycle. At this point, the tub spins constantly with intermi...
zoom-in
View photo
This message has been automatically translated
K
Kristen Seymour December 10, 2022

I would like to turn the chime on for when the washer had finished a cycle but they're are no buttons for this? Recently bought a house that came with this washer MVW6200k*

I would like to turn the chime on for when the washer had finished a cycle but they're are no buttons for this? Recently boug...
zoom-in
View photo
A
ArinJune 26, 2023

I put a refresh cleaning tablet in the washer and put the washer on clean washer setting and it ran water for a few seconds then drained and now it’s not doing anything but the lid lock light and the three lights at the top of the screen just keep flashing

I put a refresh cleaning tablet in the washer and put the washer on clean washer setting and it ran water for a few seconds t...
zoom-in
View photo
N
Nicole December 26, 2023

Is the soap tray supposed to open on its own at the end of a wash cycle? Mine does this a lot.

Is the soap tray supposed to open on its own at the end of a wash cycle? Mine does this a lot.
zoom-in
View photo
N
NatJanuary 27, 2021

6200 KW washer. Does the machine sense the amount of load of clothes to determine level of water released into the washing drum?

C
Caitlin WerthFebruary 25, 2021

How do you know when a load is complete? Right now the machine has been flashing 'sense' and 'done' alternately but the lid is still locked. Will it stay solid on 'done' when it is done? Also, how long do loads usually take? Ours seems to take hours. We ate concerned we might be doing something wrong.

1 comment
C
Charlotte ThomasApril 30, 2021

Have you solve that problem? I have same problem now and just bought this washer.

The Maytag MVW6200KW is a washing machine designed to provide efficient and reliable laundry care. It is equipped with a variety of features to enhance the washing experience. With a sizable capacity, this washing machine can accommodate large loads of laundry, making it suitable for households with heavy laundry needs. It utilizes advanced cleaning technology to effectively remove dirt and stains from clothes, ensuring thorough cleaning results. The MVW6200KW features multiple wash cycles and options, allowing users to customize their laundry settings according to their specific needs. This includes options for different fabric types and levels of soiling, enabling gentle care for delicate garments and more intensive cleaning for heavily soiled items. The washing machine is designed with an intuitive control panel that makes it easy to navigate and select the desired settings. It also offers a range of convenient features, such as a delay start option that allows users to set a specific time for the wash cycle to begin. In terms of efficiency, the MVW6200KW is built to conserve water and energy, helping to reduce utility costs and environmental impact. It operates quietly, minimizing disturbances while the machine is running. Constructed with durable materials, this washing machine is built to withstand regular use and provide long-term reliability. It is designed to function smoothly and efficiently, ensuring optimal performance over time. Overall, the Maytag MVW6200KW is a dependable and efficient washing machine that offers a range of features to simplify laundry care and deliver satisfactory cleaning results.

General
BrandMaytag
ModelMVW6200KW
Productwashing machine
EAN883049583211
LanguageEnglish
FiletypeUser manual (PDF), Quickstart Guide (PDF), Warranty information (PDF), Safety instructions (PDF), Energy label (PDF)

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Maytag MVW6200KW below.

What temperature should I use for my laundry?

The washing label of your garment shows the recommended washing temperature.

Do I need to use an anti-scaling agent for my washing machine?

It is not necessary to use an anti-scaling agent. Scale deposits can be prevented by limiting washing at high temperatures and using the recommended amount of detergent per wash.

How do I prevent my washing machine from smelling?

Unpleasant odours can be avoided by occasionally washing at 60 degrees and using the recommended amount of detergent per wash.

Why is my washing machine not turning on?

Make sure the machine is plugged into a working electrical outlet and that the circuit breaker has not tripped. Additionally, check if the washer's door is securely closed, as the machine will not operate if the door is open or not properly latched.

Why is my laundry coming out still wet?

Ensure that the selected cycle and settings match your laundry load. If using a high-efficiency detergent, make sure it is appropriate for your type of load. Check if the drain hose is properly connected and not kinked. Adjust the spin speed if necessary, as a slower speed may leave clothes damp.

Why does my washer make excessive noise during operation?

Verify that the unit is level and stable on the floor. Ensure that the load is balanced inside the drum, as unbalanced loads can cause increased noise. Additionally, check if any foreign objects, such as coins or buttons, are trapped inside the tub or pump, as they can contribute to the noise.

How can I clean the washing machine drum?

Run a cleaning cycle with a washing machine cleaner specifically designed to remove dirt and residue. Alternatively, you can wipe the drum interior using a mixture of mild detergent and water, making sure to rinse thoroughly afterward. Avoid using abrasive cleaners or bleach, as they may damage the drum.

Why is my washer displaying error codes?

Different error codes indicate specific issues. To troubleshoot, try turning off the washer and unplugging it for a few minutes before restarting. If the error persists, consult the user manual for a list of error codes and their corresponding solutions. You can also contact customer support for further assistance.

Is the manual of the Maytag MVW6200KW available in English?

Yes, the manual of the Maytag MVW6200KW is available in English .

Is your question not listed? Ask your question here

No results