Maytag MVW6200KW manual

Maytag MVW6200KW
9.1 · 14
PDF manual
 · 132 pages
English
manualMaytag MVW6200KW

PARA SER USADO ÚNICAMENTE POR TÉCNICOS DE SERVICIO

NO QUITAR NI DESTRUIR112

PRUEBAS DE SOLUCIÓN DE PROBLEMAS

PRUEBA N.° 1: Control principal (ACU)
Esta prueba permite comprobar la alimentación entrante y saliente del
control principal. Esta prueba da por sentado que existe una tensión
correcta en el tomacorriente.
1. Desenchufe la lavadora o desconecte el suministro de energía.
2. Retire la consola para acceder al control principal.
3. Compruebe que todos los conectores estén completamente insertados
en el control principal.
4. Con un voltímetro configurado para CA, conecte la sonda negra a J1-1
(neutro) y la sonda roja a J1-2 (línea). Enchufe la lavadora o reconecte
el suministro de energía.
Si hay 120 V CA, continúe en el paso 5.
Si no detecta 120 V CA, revise la continuidad del cable de alimentación
de CA (consulte la Figura 7).
5. ¿El “Indicador LED de diagnóstico” destella o está encendido o
apagado de forma continua? (Consulte la Figura 1 para conocer la
ubicación del indicador LED).
Destella: (+5 V CC presente y el micro funciona) proceda a la prueba
de la HMI.
ON (Encendido): (+5 V CC pero el micro falla) continúe con el paso 8.
OFF (Apagado): (No hay +5 V CC o el micro falla) continúe con el paso 6.
6. Verifique si la HMI de la consola está afectando el suministro de CC del
control principal.
a. Desenchufe la lavadora o desconecte el suministro de energía.
b. Retire el conector J5 del control principal.
c. Enchufe la lavadora o reconecte el suministro de energía.
7. Realice comprobaciones de tensión dentro del cabezal J5 en la placa;
no una en cortocircuito los terminales.
a. Con un voltímetro configurado para CC, conecte la sonda negra a J5-4
(Circ. tierra) y la sonda roja a J5-1 (+12 V CC).
Si no detecta tensión de CC, vaya al paso 8.
Si la tensión de CC está presente, pero el indicador LED de diagnóstico
no destella, continúe con el paso 8.
8. El Control principal funcionó incorrectamente.
a. Desenchufe la lavadora o desconecte el suministro de energía.
b. Reemplace el control principal.
c. Vuelva a ensamblar todas las piezas y los paneles.
d. Enchufe la lavadora o reconecte el suministro de energía. Realice el
ciclo de diagnóstico de servicio para verificar la reparación.

PRUEBA N.° 2: Válvulas

Esta prueba permite verificar las conexiones eléctricas a las válvulas y las
válvulas mismas.
1. Realice la prueba de la válvula de agua para verificar los relés y las
conexiones eléctricas hacia las válvulas, según lo que se indica en
Activación de componente. Cada prueba activa y desactiva la válvula
seleccionada. Los siguientes pasos dan por sentado que una (o más)
válvula(s) no se activaron.
2. Para las válvulas en cuestión, compruebe las válvulas solenoides
individuales.
a. Desenchufe la lavadora o desconecte el suministro de energía.
b. Retire la consola para acceder al control principal.
c. Retire el conector J8 del control principal. Consulte la Figura 7: Control
principal.
d. Verifique la continuidad del mazo de cables y la conexión a las válvulas
solenoides.
3. Compruebe la resistencia de las bobinas de válvula en las siguientes
patillas del conector J8:
Válvula Patilla
Suavizante de telas J8, 1 y 6
Hot (Caliente) J8, 1 y 5
Cold (Fría) J8, 1 y 3
La resistencia debe ser de 890-1090 Ω.
Si las lecturas de resistencia son decenas de ohmios fuera del rango,
reemplace el conjunto de la válvula.
Si las lecturas de resistencia están dentro del rango, reemplace el
control principal y realice el diagnóstico de servicio para verificar la
reparación.

PRUEBA N.° 3: Sistema de accionamiento

1. Ingrese al modo de servicio y visualice los códigos de fallas. Si se
muestran las fallas F7E1, F7E3, F7E4, F7E6 o F7E7, es probable que
haya un problema relacionado con el motor o el variador. Tome nota de
las fallas y bórrelas.
2. Después de borrar los códigos de error, ingrese al modo Component
Activation (Activación de componentes) y ejecute la prueba de agitación
lenta. Si el motor funciona después de 15 a 20 segundos, no se trata
de un problema del motor, del control ni de las conexiones del mazo
de cables del motor.
3. A continuación, dentro del modo Component Activation (Activación
de componentes), ejecute el ciclo Spin Low Speed (Centrifugar a baja
velocidad). Si el motor zumba brevemente y luego se apaga, vaya al
modo de visualización de códigos de fallas y verifique si hay códigos
de fallas.
4. Después de ejecutar la prueba de agitación y centrifugado, revise si hay
códigos de fallas.

PRUEBA N.º 3a: Sistema de accionamiento: variador

Esta prueba verifica las conexiones, la bobina del variador y el mazo de cables.
NOTA: Para que el motor pueda agitar o centrifugar, la tapa debe estar
cerrada y bloqueada.
IMPORTANTE: Drene el agua del tambor antes de acceder al fondo de la
lavadora.
Comprobación de funcionamiento:
1. Para revisar el variador y las conexiones eléctricas, realice las pruebas
de centrifugado y lavado en el modo Component Activation (Activación
de componentes). Los pasos siguientes suponen que este paso no dio
resultado.
2. Desenchufe la lavadora o desconecte el suministro de energía.
3. El motor y el variador deben poder girarse independientemente uno del
otro. Si están bloqueados juntos, hay un problema con la corredera del
variador. Continúe en el paso 11.
Si la canasta y el impulsor giran libremente, vaya al paso 4.
Si la canasta o el impulsor no giran libremente, determine la causa de la
fricción mecánica o el bloqueo.
4. Retire la consola para acceder al control principal.
5. Compruebe visualmente que los conectores J2 y J6 estén
completamente insertados en el control principal.
Si pasan la prueba visual, vaya al paso 6.
Si los conectores no están debidamente insertados, vuelva a conectar
los conectores J2 y J6 y repita el paso 1.
Motor del variador:
NOTA: antes de iniciar la comprobación eléctrica, verifique que la leva en la
transmisión se mueva libremente sin atascarse.

View the manual for the Maytag MVW6200KW here, for free. This manual comes under the category washing machines and has been rated by 14 people with an average of a 9.1. This manual is available in the following languages: English. Do you have a question about the Maytag MVW6200KW or do you need help? Ask your question here

Need help?

Do you have a question about the Maytag and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 216
A
Annetta SmallJune 10, 2024

how many gallons of water for one load? What is the range of gallons of water for the different cycles?

P
Patrick Mahoney June 2, 2024

My Maytag washer mvw6200kw2 starts preliminary spin doesn’t fill than goes to drain in done cycle

B
Beverly MasoveroJuly 21, 2021

If washer load not level how can I shift load without starting cycle all over again? Model mvw6200kw1

If washer load not level how can I shift load without starting cycle all over again? Model mvw6200kw1
zoom-in
View photo
N
Nancy KeysonOctober 10, 2021

I will be having this washer delivered in a week. I see that reviews are stating problems with draining. I had this problem with a Midea that was only 2 weeks old. Is there a pump filter that the consumer can clean?

I will be having this washer delivered in a week. I see that reviews are stating problems with draining. I had this problem w...
zoom-in
View photo
S
SandraOctober 23, 2021

Done 2 loads. My new washer works until it gets to the rinse/spin cycle. At this point, the tub spins constantly with intermittent spurts of water, never filling to rinse the load. It then continues to spin. I eventually had to stop the cycle using the power button. Anyone? Thanks. Translation: I have completed 2 loads of laundry. My new washing machine works well until it reaches the rinse/spin cycle. At this point, the tub keeps spinning continuously with occasional bursts of water, but it never fills up to rinse the load. After that, it continues to spin without progressing. Eventually, I had to stop the cycle by using the power button. Does anyone have any solutions? Thank you.

Done 2 loads. My new washer works until it gets to the rinse/spin cycle. At this point, the tub spins constantly with intermi...
zoom-in
View photo
This message has been automatically translated
K
Kristen Seymour December 10, 2022

I would like to turn the chime on for when the washer had finished a cycle but they're are no buttons for this? Recently bought a house that came with this washer MVW6200k*

I would like to turn the chime on for when the washer had finished a cycle but they're are no buttons for this? Recently boug...
zoom-in
View photo
A
ArinJune 26, 2023

I put a refresh cleaning tablet in the washer and put the washer on clean washer setting and it ran water for a few seconds then drained and now it’s not doing anything but the lid lock light and the three lights at the top of the screen just keep flashing

I put a refresh cleaning tablet in the washer and put the washer on clean washer setting and it ran water for a few seconds t...
zoom-in
View photo
N
Nicole December 26, 2023

Is the soap tray supposed to open on its own at the end of a wash cycle? Mine does this a lot.

Is the soap tray supposed to open on its own at the end of a wash cycle? Mine does this a lot.
zoom-in
View photo
N
NatJanuary 27, 2021

6200 KW washer. Does the machine sense the amount of load of clothes to determine level of water released into the washing drum?

C
Caitlin WerthFebruary 25, 2021

How do you know when a load is complete? Right now the machine has been flashing 'sense' and 'done' alternately but the lid is still locked. Will it stay solid on 'done' when it is done? Also, how long do loads usually take? Ours seems to take hours. We ate concerned we might be doing something wrong.

1 comment
C
Charlotte ThomasApril 30, 2021

Have you solve that problem? I have same problem now and just bought this washer.

The Maytag MVW6200KW is a washing machine designed to provide efficient and reliable laundry care. It is equipped with a variety of features to enhance the washing experience. With a sizable capacity, this washing machine can accommodate large loads of laundry, making it suitable for households with heavy laundry needs. It utilizes advanced cleaning technology to effectively remove dirt and stains from clothes, ensuring thorough cleaning results. The MVW6200KW features multiple wash cycles and options, allowing users to customize their laundry settings according to their specific needs. This includes options for different fabric types and levels of soiling, enabling gentle care for delicate garments and more intensive cleaning for heavily soiled items. The washing machine is designed with an intuitive control panel that makes it easy to navigate and select the desired settings. It also offers a range of convenient features, such as a delay start option that allows users to set a specific time for the wash cycle to begin. In terms of efficiency, the MVW6200KW is built to conserve water and energy, helping to reduce utility costs and environmental impact. It operates quietly, minimizing disturbances while the machine is running. Constructed with durable materials, this washing machine is built to withstand regular use and provide long-term reliability. It is designed to function smoothly and efficiently, ensuring optimal performance over time. Overall, the Maytag MVW6200KW is a dependable and efficient washing machine that offers a range of features to simplify laundry care and deliver satisfactory cleaning results.

General
BrandMaytag
ModelMVW6200KW
Productwashing machine
EAN883049583211
LanguageEnglish
FiletypeUser manual (PDF), Quickstart Guide (PDF), Warranty information (PDF), Safety instructions (PDF), Energy label (PDF)

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Maytag MVW6200KW below.

What temperature should I use for my laundry?

The washing label of your garment shows the recommended washing temperature.

Do I need to use an anti-scaling agent for my washing machine?

It is not necessary to use an anti-scaling agent. Scale deposits can be prevented by limiting washing at high temperatures and using the recommended amount of detergent per wash.

How do I prevent my washing machine from smelling?

Unpleasant odours can be avoided by occasionally washing at 60 degrees and using the recommended amount of detergent per wash.

Why is my washing machine not turning on?

Make sure the machine is plugged into a working electrical outlet and that the circuit breaker has not tripped. Additionally, check if the washer's door is securely closed, as the machine will not operate if the door is open or not properly latched.

Why is my laundry coming out still wet?

Ensure that the selected cycle and settings match your laundry load. If using a high-efficiency detergent, make sure it is appropriate for your type of load. Check if the drain hose is properly connected and not kinked. Adjust the spin speed if necessary, as a slower speed may leave clothes damp.

Why does my washer make excessive noise during operation?

Verify that the unit is level and stable on the floor. Ensure that the load is balanced inside the drum, as unbalanced loads can cause increased noise. Additionally, check if any foreign objects, such as coins or buttons, are trapped inside the tub or pump, as they can contribute to the noise.

How can I clean the washing machine drum?

Run a cleaning cycle with a washing machine cleaner specifically designed to remove dirt and residue. Alternatively, you can wipe the drum interior using a mixture of mild detergent and water, making sure to rinse thoroughly afterward. Avoid using abrasive cleaners or bleach, as they may damage the drum.

Why is my washer displaying error codes?

Different error codes indicate specific issues. To troubleshoot, try turning off the washer and unplugging it for a few minutes before restarting. If the error persists, consult the user manual for a list of error codes and their corresponding solutions. You can also contact customer support for further assistance.

Is the manual of the Maytag MVW6200KW available in English?

Yes, the manual of the Maytag MVW6200KW is available in English .

Is your question not listed? Ask your question here

No results