Maytag MVW6200KW manual

Maytag MVW6200KW
9.1 · 14
PDF manual
 · 132 pages
English
manualMaytag MVW6200KW

FOR SERVICE TECHNICIAN’S USE ONLY

DO NOT REMOVE OR DESTROY10

SERVICE GUIDE

Before servicing, check the following:
Ƀ
Make sure there is power at the wall outlet.
Ƀ
Has a household fuse blown or circuit breaker tripped? Was a regular
fuse used? Inform customer that a time-delay fuse is required.
Ƀ
Are both hot and cold water faucets open and water supply hoses
unobstructed?
Ƀ
Make sure drain hose is not sealed into drain pipe, and that there is an
air gap for ventilation. Ensure drain height is between 39" (991 mm)
and 8' (2.4 m) above the floor.
Ƀ
All tests/checks should be made with a VOM (volt-ohm-milliammeter)
or DVM (digital-voltmeter) having a sensitivity of 20,000 Ω per VDC or
greater.
Ƀ
Resistance checks must be made with washer unplugged or power
disconnected.
IMPORTANT: Avoid using large diameter probes when checking
harness connectors as the probes may damage the connectors upon
insertion.
Ƀ
Check all harnesses and connections before replacing components.
Look for connectors not fully seated, broken or loose wires and
terminals, or wires not pressed into connectors far enough to engage
metal barbs.
Ƀ
A potential cause of a control not washer functioning is corrosion
or contamination on connections. Use an ohmmeter to check for
continuity across suspected connections.
Ƀ
To properly check voltage:
1. Unplug appliance or disconnect power.
2. Attach voltage measurement probes to proper connectors.
3. Plug in appliance or reconnect power and verify voltage reading.
4. Unplug appliance or disconnect power after completing voltage
measurements.

DIAGNOSTIC LED – MAIN CONTROL (ACU)

A troubleshooting tool has been implemented onto the main control
board—a diagnostic LED.
LED Flashing – The Control is detecting correct incoming line voltage and
the processor is functioning.
LED OFF or ON – Control malfunction. Perform TEST #1: Main Control
(ACU), to verify main control functionality.
Figure 1 - Diagnostic LED

SERVICE MODE

These tests allow factory or service personnel to test and verify all
inputs to the main control board. You may want to do a quick and
overall checkup of the washer with these tests before going to specific
troubleshooting tests.

ACTIVATING SERVICE MODE

1. Be sure the washer is in standby mode (plugged in with all LEDs
off).
2. Follow the steps below within 8 seconds:
dz Press and Release Key 1
dz Press and Release Key 2
dz Press and Release Key 3
dz Repeat this 3 button sequence 2 more times
3. If this test mode has been entered successfully, all indicators on
the HMI will be illuminated for 1 second then will be turned OFF.
After this, If there are no saved fault codes, the STATUS indicators
(Sense, Soak, Wash and Done) will blink two times and then all the
indicators will be turned OFF.
LED group 2
LED group 5
LED group 6
LED
group 1
LED
group 3
LED group 4
Key 6/
POWER
Key 5/
START
Key 4Key 3
Key 2
Key 1
Figure 2: Diagram of the HMI screen and navigational buttons.
Unsuccessful Activation
If entry into Diagnostic mode is unsuccessful, refer to the following
indications and actions:
Indication: None of the LEDs will turn on.
Action: Turn on the appliance by pressing the POWER Button or rotating
the knob and select any cycle.
If LEDs turn on after pressing the POWER Button or turning the
knob, then try to enter Service mode again: repeat step 2 mentioned
in activating sequence and complete it within 8 seconds. If these
re-entry procedures fail to enter into Diagnostic mode, there is likely
a faulty button in the HMI. Replace the HMI.
If no LEDs come on after selecting the cycle, go to TEST #1: Main
Control (ACU).
Activation with Saved Fault Codes
If there is a saved fault code, it will be flashing in the display. Review the
Fault/Error Codes table on page 16 for the recommended procedure. If
there is no saved fault code. All LEDs will turn OFF.
LED
Location
Status
Indicator

View the manual for the Maytag MVW6200KW here, for free. This manual comes under the category washing machines and has been rated by 14 people with an average of a 9.1. This manual is available in the following languages: English. Do you have a question about the Maytag MVW6200KW or do you need help? Ask your question here

Need help?

Do you have a question about the Maytag and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 216
A
Annetta SmallJune 10, 2024

how many gallons of water for one load? What is the range of gallons of water for the different cycles?

P
Patrick Mahoney June 2, 2024

My Maytag washer mvw6200kw2 starts preliminary spin doesn’t fill than goes to drain in done cycle

B
Beverly MasoveroJuly 21, 2021

If washer load not level how can I shift load without starting cycle all over again? Model mvw6200kw1

If washer load not level how can I shift load without starting cycle all over again? Model mvw6200kw1
zoom-in
View photo
N
Nancy KeysonOctober 10, 2021

I will be having this washer delivered in a week. I see that reviews are stating problems with draining. I had this problem with a Midea that was only 2 weeks old. Is there a pump filter that the consumer can clean?

I will be having this washer delivered in a week. I see that reviews are stating problems with draining. I had this problem w...
zoom-in
View photo
S
SandraOctober 23, 2021

Done 2 loads. My new washer works until it gets to the rinse/spin cycle. At this point, the tub spins constantly with intermittent spurts of water, never filling to rinse the load. It then continues to spin. I eventually had to stop the cycle using the power button. Anyone? Thanks. Translation: I have completed 2 loads of laundry. My new washing machine works well until it reaches the rinse/spin cycle. At this point, the tub keeps spinning continuously with occasional bursts of water, but it never fills up to rinse the load. After that, it continues to spin without progressing. Eventually, I had to stop the cycle by using the power button. Does anyone have any solutions? Thank you.

Done 2 loads. My new washer works until it gets to the rinse/spin cycle. At this point, the tub spins constantly with intermi...
zoom-in
View photo
This message has been automatically translated
K
Kristen Seymour December 10, 2022

I would like to turn the chime on for when the washer had finished a cycle but they're are no buttons for this? Recently bought a house that came with this washer MVW6200k*

I would like to turn the chime on for when the washer had finished a cycle but they're are no buttons for this? Recently boug...
zoom-in
View photo
A
ArinJune 26, 2023

I put a refresh cleaning tablet in the washer and put the washer on clean washer setting and it ran water for a few seconds then drained and now it’s not doing anything but the lid lock light and the three lights at the top of the screen just keep flashing

I put a refresh cleaning tablet in the washer and put the washer on clean washer setting and it ran water for a few seconds t...
zoom-in
View photo
N
Nicole December 26, 2023

Is the soap tray supposed to open on its own at the end of a wash cycle? Mine does this a lot.

Is the soap tray supposed to open on its own at the end of a wash cycle? Mine does this a lot.
zoom-in
View photo
N
NatJanuary 27, 2021

6200 KW washer. Does the machine sense the amount of load of clothes to determine level of water released into the washing drum?

C
Caitlin WerthFebruary 25, 2021

How do you know when a load is complete? Right now the machine has been flashing 'sense' and 'done' alternately but the lid is still locked. Will it stay solid on 'done' when it is done? Also, how long do loads usually take? Ours seems to take hours. We ate concerned we might be doing something wrong.

1 comment
C
Charlotte ThomasApril 30, 2021

Have you solve that problem? I have same problem now and just bought this washer.

The Maytag MVW6200KW is a washing machine designed to provide efficient and reliable laundry care. It is equipped with a variety of features to enhance the washing experience. With a sizable capacity, this washing machine can accommodate large loads of laundry, making it suitable for households with heavy laundry needs. It utilizes advanced cleaning technology to effectively remove dirt and stains from clothes, ensuring thorough cleaning results. The MVW6200KW features multiple wash cycles and options, allowing users to customize their laundry settings according to their specific needs. This includes options for different fabric types and levels of soiling, enabling gentle care for delicate garments and more intensive cleaning for heavily soiled items. The washing machine is designed with an intuitive control panel that makes it easy to navigate and select the desired settings. It also offers a range of convenient features, such as a delay start option that allows users to set a specific time for the wash cycle to begin. In terms of efficiency, the MVW6200KW is built to conserve water and energy, helping to reduce utility costs and environmental impact. It operates quietly, minimizing disturbances while the machine is running. Constructed with durable materials, this washing machine is built to withstand regular use and provide long-term reliability. It is designed to function smoothly and efficiently, ensuring optimal performance over time. Overall, the Maytag MVW6200KW is a dependable and efficient washing machine that offers a range of features to simplify laundry care and deliver satisfactory cleaning results.

General
BrandMaytag
ModelMVW6200KW
Productwashing machine
EAN883049583211
LanguageEnglish
FiletypeUser manual (PDF), Quickstart Guide (PDF), Warranty information (PDF), Safety instructions (PDF), Energy label (PDF)

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Maytag MVW6200KW below.

What temperature should I use for my laundry?

The washing label of your garment shows the recommended washing temperature.

Do I need to use an anti-scaling agent for my washing machine?

It is not necessary to use an anti-scaling agent. Scale deposits can be prevented by limiting washing at high temperatures and using the recommended amount of detergent per wash.

How do I prevent my washing machine from smelling?

Unpleasant odours can be avoided by occasionally washing at 60 degrees and using the recommended amount of detergent per wash.

Why is my washing machine not turning on?

Make sure the machine is plugged into a working electrical outlet and that the circuit breaker has not tripped. Additionally, check if the washer's door is securely closed, as the machine will not operate if the door is open or not properly latched.

Why is my laundry coming out still wet?

Ensure that the selected cycle and settings match your laundry load. If using a high-efficiency detergent, make sure it is appropriate for your type of load. Check if the drain hose is properly connected and not kinked. Adjust the spin speed if necessary, as a slower speed may leave clothes damp.

Why does my washer make excessive noise during operation?

Verify that the unit is level and stable on the floor. Ensure that the load is balanced inside the drum, as unbalanced loads can cause increased noise. Additionally, check if any foreign objects, such as coins or buttons, are trapped inside the tub or pump, as they can contribute to the noise.

How can I clean the washing machine drum?

Run a cleaning cycle with a washing machine cleaner specifically designed to remove dirt and residue. Alternatively, you can wipe the drum interior using a mixture of mild detergent and water, making sure to rinse thoroughly afterward. Avoid using abrasive cleaners or bleach, as they may damage the drum.

Why is my washer displaying error codes?

Different error codes indicate specific issues. To troubleshoot, try turning off the washer and unplugging it for a few minutes before restarting. If the error persists, consult the user manual for a list of error codes and their corresponding solutions. You can also contact customer support for further assistance.

Is the manual of the Maytag MVW6200KW available in English?

Yes, the manual of the Maytag MVW6200KW is available in English .

Is your question not listed? Ask your question here

No results