Maytag MAT20CS manual

Maytag MAT20CS
7.5 · 1
PDF manual
 · 4 pages
English
manualMaytag MAT20CS

Quick Start Guide

Setting Up and Using Your Top Load Washer

CONNECT INLET HOSES
TO FAUCETS
1
CONNECT INLET
HOSES TO WASHER &
CHECK FOR LEAKS
3
Do not overtighten or use tape or sealants when attaching to faucets.Make sure that both hot and cold water hoses are connected to the correct faucets. The washer will not operate unless both hoses are connected.
IMPORTANT:
Make sure that water faucets are turned on fully before using the washer for the rst time.If there is no/low water pressure to the washer, the cycle status lights will appear as shown at right. To clear, open and close the lid.
4
CHANGING COIN SLIDE PRICING
Refer to W10813856 Coin Slide Installation Instructions for detailed instructions located in the coin box.*Applies only to select models.
CLEAR
WATER LINES
2
Do not overtighten or use tape or sealants when attaching to washer.

KEYS, COIN SLIDE, AND COIN BOX*

FREE FAX
800-ESD-KEYS
012124
DO NOT
DUPLICATE
LOCATION OF KEYS
Coin box key (shown) comes taped to coin box lock.Service door key is locked inside coin box.Document the key code (engraved on coin box key) in a safe place.If key is lost, contact 1-800-523-1510 for replacement (not covered by warranty). Have key code handy; otherwise, locksmithwill have to drill out coin box and replacement coin box (part no. 4396671) will have to be installed.*Applies only to select models.W10837642A W10862486A - SP

CONNECTING WATER

Make sure that the washer is level (see the “Level Washer” section in the Installation Instructions). Run a wash cycle to verify that the washer is working correctly and has no leaks at faucets and inlet hoses.Insert new hose washers (in separate bag) into each end of inlet hoses. Firmly seat washers into couplings.Turn on faucets and check for leaks at both ends of hoses.
In
Use
Soak/
Wash
Rinse
Final
Spin
Done
Lid
Locked
CYCLE STATUS
In
Use
Soak/
Wash
Rinse
Final
Spin
Done
Lid
Locked
CYCLE STATUS
In
Use
Soak/
Wash
Rinse
Final
Spin
Done
Lid
Locked
In
Use
Soak/
Wash
Rinse
Final
Spin
Done
Lid
Locked
In
Use
Soak/
Wash
Rinse
Final
Spin
Done
Lid
Locked
In
Use
Soak/
Wash
Rinse
Final
Spin
Done
CYCLE STATUS
CYCLE STATUS
CYCLE STATUS
CYCLE STATUS

View the manual for the Maytag MAT20CS here, for free. This manual comes under the category washing machines and has been rated by 1 people with an average of a 7.5. This manual is available in the following languages: English. Do you have a question about the Maytag MAT20CS or do you need help? Ask your question here

Need help?

Do you have a question about the Maytag and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

The Maytag MAT20CS is a washing machine designed for commercial use. It is crafted with a sturdy and reliable build to ensure long-lasting performance in high-demand environments. The machine is equipped with a variety of features that make it suitable for commercial applications. The Maytag MAT20CS has a large capacity drum that can handle substantial loads, allowing for efficient cleaning of a significant amount of laundry at once. This can save time and resources in commercial settings, such as laundromats or hotels. With multiple cycle options, including normal, delicate, and heavy-duty, the MAT20CS offers versatility to accommodate various types of fabrics and washing needs. It also includes adjustable water levels and temperature controls, allowing for customizable wash cycles. The machine is equipped with a robust agitator that ensures thorough and efficient cleaning of clothes. It utilizes powerful agitation to effectively remove dirt, stains, and grime from garments. In terms of durability, the Maytag MAT20CS is constructed with high-quality materials that can withstand heavy usage over an extended period. Its rugged build ensures resistance to wear and tear, contributing to its longevity and reliability. Overall, the Maytag MAT20CS is an efficient and durable washing machine suitable for commercial use. Its large capacity, multiple cycle options, and sturdy construction make it an ideal choice for businesses in need of a reliable laundry solution.

General
BrandMaytag
ModelMAT20CS
Productwashing machine
EAN883049400334
LanguageEnglish
FiletypeUser manual (PDF), Installation Guide (PDF), Datasheet (PDF)

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Maytag MAT20CS below.

What temperature should I use for my laundry?

The washing label of your garment shows the recommended washing temperature.

Do I need to use an anti-scaling agent for my washing machine?

It is not necessary to use an anti-scaling agent. Scale deposits can be prevented by limiting washing at high temperatures and using the recommended amount of detergent per wash.

How do I prevent my washing machine from smelling?

Unpleasant odours can be avoided by occasionally washing at 60 degrees and using the recommended amount of detergent per wash.

How do I start using the Maytag MAT20CS washing machine?

To start using the Maytag MAT20CS washing machine, follow these steps: 1. Connect the inlet hoses to the faucets: Attach the hot water hose to the hot water faucet and the cold water hose to the cold water faucet. Make sure not to overtighten or use tape or sealants when attaching the hoses. Both hoses must be connected for the washer to operate. 2. Check for leaks: Once the hoses are connected, turn on the water faucets fully. Check for any leaks at both ends of the hoses and at the faucets. If there are any leaks, tighten the connections or replace the washers. 3. Ensure water pressure: If there is no or low water pressure to the washer, the cycle status lights may appear a certain way. To clear this, open and close the lid of the washer. 4. Verify coin slide pricing (if applicable): If you need to change the slide pricing, refer to the detailed instructions in the Coin Slide Installation Instructions provided with the washer. 5. Purge the water lines: Before using the washer, it is recommended to purge the water lines. This can be done by running a wash cycle to verify that the washer is working correctly and has no leaks at the faucets and inlet hoses. Please note that these steps are a general guide and may vary slightly depending on the specific model of the Maytag MAT20CS washing machine.

What should I do if I encounter issues while setting up and using my top-loading washer?

If you encounter issues while setting up and using your Maytag MAT20CS top-loading washer, follow these steps: 1. Check the inlet hoses: Ensure that the inlet hoses are properly connected to the washer and the faucets. Make sure not to overtighten or use tape or sealants when attaching them. Both the hot and cold water hoses should be connected to the correct faucets. 2. Verify water pressure: If there is no or low water pressure to the washer, the cycle status lights may appear a certain way. To resolve this, open and close the lid of the washer. 3. Inspect for leaks: Check for any leaks at both ends of the inlet hoses and at the faucets. If there are any leaks, tighten the connections or replace the washers. 4. Adjust coin slide pricing (if applicable): Refer to the detailed instructions in the Coin Slide Installation Instructions provided with the washer to modify the slide pricing. 5. Purge the water lines: Before using the washer, it is recommended to run a wash cycle to verify that the washer is working correctly and has no leaks at the faucets and inlet hoses. Please note that these steps are a general guide and may vary slightly depending on the specific model of the Maytag MAT20CS washing machine.

How do I connect the water inlet hoses to the faucets?

To connect the water inlet hoses to the faucets of your Maytag MAT20CS washing machine, follow these steps: 1. Insert new hose washers: Take the new hose washers provided and insert them into each end of the inlet hoses. Make sure the washers are firmly seated into the couplings. 2. Connect the hoses to the washer: Attach one end of the hot water hose to the hot water faucet on the washer and the other end to the hot water faucet on the wall. Similarly, connect one end of the cold water hose to the cold water faucet on the washer and the other end to the cold water faucet on the wall. Ensure that the hoses are securely attached, but avoid overtightening. 3. Check for leaks: Once the hoses are connected, turn on the water faucets fully. Inspect both ends of the hoses and the connections at the faucets for any leaks. If you notice any leaks, tighten the connections or replace the washers. 4. Verify water flow: After connecting the hoses, run a wash cycle to confirm that the water is flowing properly into the washer. This will help ensure that the connections are secure and there are no leaks. Please note that these steps are a general guide and may vary slightly depending on the specific model of the Maytag MAT20CS washing machine.

How can I change the slide pricing on the Maytag MAT20CS washing machine?

To change the slide pricing on the Maytag MAT20CS washing machine, follow these steps: 1. Refer to the Coin Slide Installation Instructions: Locate the Coin Slide Installation Instructions provided with the washer. These instructions will provide detailed steps on how to change the slide pricing. 2. Follow the instructions: Read and follow the instructions carefully to ensure that you understand the process. The instructions will guide you through the necessary steps to modify the slide pricing. Please note that the specific steps for changing the slide pricing may vary depending on the model of the Maytag MAT20CS washing machine. It is important to refer to the Coin Slide Installation Instructions provided with your washer for accurate and detailed instructions. If you do not have access to the Coin Slide Installation Instructions or require further assistance, it is recommended to contact Maytag customer support for additional guidance.

What is the process for purging the water lines of the washing machine?

To purge the water lines of the Maytag MAT20CS washing machine, follow these steps: 1. Turn on the water faucets: Ensure that the water faucets connected to the washer are fully open. 2. Run a wash cycle: Select a wash cycle on the washer and start the machine. Allow the washer to run through a complete cycle without any laundry inside. 3. Check for leaks: While the wash cycle is running, inspect the connections at the faucets and the inlet hoses for any leaks. If you notice any leaks, tighten the connections or replace the washers. 4. Verify proper water flow: During the wash cycle, observe the water flow into the washer. Ensure that the water is flowing steadily and there are no interruptions or irregularities. 5. Monitor for any issues: Pay attention to any unusual sounds, vibrations, or error messages displayed on the washer's control panel. If you encounter any issues, refer to the troubleshooting section of the manual or contact Maytag customer support for further assistance. Please note that these steps are a general guide and may vary slightly depending on the specific model of the Maytag MAT20CS washing machine.

How do I start using the Maytag MAT20CS washing machine?

To start using the Maytag MAT20CS washing machine, follow these steps: 1. Connect the inlet hoses to the faucets: Attach the hot water hose to the hot water faucet and the cold water hose to the cold water faucet. Make sure not to overtighten or use tape or sealants when attaching the hoses. Both hoses must be connected for the washer to operate properly. 2. Check for leaks: After connecting the hoses, check for any leaks at the faucet connections and the ends of the hoses. If there are any leaks, tighten the connections or replace the washers if necessary. 3. Turn on the water faucets: Ensure that both the hot and cold water faucets are fully opened before using the washer for the first time. This will ensure proper water flow during the wash cycle. 4. Verify cycle status: Once the water is connected, the cycle status indicators on the washer will show the current status of the wash cycle. Familiarize yourself with the different indicators, such as "In Use," "Soak/Wash," "Rinse," "Final Spin/Lid Locked," and "Done," to understand the progress of the wash cycle. By following these steps, you can start using the Maytag MAT20CS washing machine efficiently.

How can I change the pricing on the coin slide of the Maytag MAT20CS washing machine?

To change the pricing on the coin slide of the Maytag MAT20CS washing machine, follow these steps: 1. Refer to the "Coin Slide Installation Instructions" document (part number W10813856) located in the coin box for detailed instructions on changing the pricing. This document provides specific guidance on how to modify the coin slide. 2. Locate the coin box on the washing machine. The coin box contains the coin slide and is typically located on the front or top of the machine. 3. Open the coin box using the key provided. The key is usually taped to the coin box lock. If the key is lost, contact 1-800-523-1510 for a replacement (not covered by warranty). Document the key code engraved on the coin box key in a safe place. 4. Inside the coin box, you will find the coin slide. Follow the instructions in the "Coin Slide Installation Instructions" document to adjust the pricing. The document will provide step-by-step guidance on how to change the pricing settings. By following these steps, you can successfully change the pricing on the coin slide of the Maytag MAT20CS washing machine.

What should I do if I lose the keys for the coin box and service door of the Maytag MAT20CS washing machine?

If you have lost the keys for the coin box and service door of the Maytag MAT20CS washing machine, follow these steps: 1. Contact 1-800-523-1510 to request a replacement key for the coin box. Please note that the replacement key is not covered by warranty. 2. Provide the key code engraved on the coin box key to the customer service representative. This key code is important for obtaining the correct replacement key. 3. If you have also lost the key for the service door, inform the customer service representative about this as well. They will provide further guidance on how to proceed. 4. Once you receive the replacement key(s), carefully unlock the coin box and service door using the new key(s). 5. Document the key code(s) of the replacement key(s) in a safe place to avoid future loss. By following these steps, you can address the issue of lost keys for the coin box and service door of the Maytag MAT20CS washing machine.

How do I properly connect the water inlet hoses to the Maytag MAT20CS washing machine?

To properly connect the water inlet hoses to the Maytag MAT20CS washing machine, follow these steps: 1. Locate the inlet hoses: The inlet hoses are usually color-coded, with the red hose representing hot water and the blue hose representing cold water. 2. Connect the hoses to the faucets: Attach the hot water hose to the hot water faucet and the cold water hose to the cold water faucet. Ensure that the connections are secure but not overtightened. Do not use tape or sealants when attaching the hoses. 3. Connect the hoses to the washer: Attach the other ends of the hoses to the corresponding hot and cold water inlet valves on the back of the washing machine. Again, make sure the connections are secure. 4. Check for leaks: After connecting the hoses, turn on the water faucets and check for any leaks at the faucet connections and the ends of the hoses. If there are any leaks, tighten the connections or replace the washers if necessary. 5. Verify water flow: Once the hoses are connected and there are no leaks, turn on the water faucets fully to ensure proper water flow during the wash cycle. By following these steps, you can properly connect the water inlet hoses to the Maytag MAT20CS washing machine.

What does it mean when the cycle status indicator on the Maytag MAT20CS washing machine shows "In Use" or "Done"?

The cycle status indicators on the Maytag MAT20CS washing machine provide information about the progress of the wash cycle. Here is what each indicator means: 1. "In Use": This indicator remains lit after the cycle starts and stays on until the cycles are completed and the washer enters the "Done" status. It indicates that the washer is currently in use. 2. "Done": This indicator remains lit when the cycle is complete and turns off when the lid is opened. It signifies that the wash cycle has finished, and you can now open the lid to remove your laundry. Please note that the manual provides additional information about other cycle status indicators, such as "Soak/Wash," "Rinse," and "Final Spin/Lid Locked." However, since you specifically asked about "In Use" and "Done," these are the indicators that are relevant to your question. By understanding the meaning of these cycle status indicators, you can easily track the progress of your wash cycle on the Maytag MAT20CS washing machine.

Is the manual of the Maytag MAT20CS available in English?

Yes, the manual of the Maytag MAT20CS is available in English .

Is your question not listed? Ask your question here

No results