Mastercook WK-Cristal manual

Mastercook WK-Cristal
6.1 · 1
PDF manual
 · 32 pages
English
manualMastercook WK-Cristal
2

Manual

View the manual for the Mastercook WK-Cristal here, for free. This manual comes under the category exhaust hoods and has been rated by 1 people with an average of a 6.1. This manual is available in the following languages: English. Do you have a question about the Mastercook WK-Cristal or do you need help? Ask your question here

Need help?

Do you have a question about the Mastercook and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Mastercook WK-Cristal specifications

Below you will find the product specifications and the manual specifications of the Mastercook WK-Cristal.

General
BrandMastercook
ModelWK-Cristal
Productexhaust hood
LanguageEnglish
FiletypeUser manual (PDF)

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Mastercook WK-Cristal below.

When should I replace the carbon filter on my extractor hood?

The carbon filter should be replaced every three to twelve months.

How often should I clean the metal hood grease filters?

The metal grease filters should be cleaned every eight to ten weeks.

Where can I find the model number of my cooker ectractor hood?

The model number of the hood is usually found on a white label inside the hood.

How do I properly install the Mastercook WK-Cristal exhaust hood?

To properly install the Mastercook WK-Cristal exhaust hood, follow these steps: 1. Ensure that the assembly and electrical connections are carried out by specialized personnel. 2. For the electric connection, use an earth cable as the appliance is manufactured as a class I. If a plug is not provided, connect a plug suitable for the electrical load indicated on the description label. If a plug is provided, install the cooker hood in a way that the plug is easily accessible. Place an omnipolar switch with a minimum aperture of 3mm between contacts in line with the electrical load and local standards. 3. Maintain a minimum distance of at least 65cm between the support surfaces of the cooking pots on the cooker top and the lowest part of the cooker hood. If a connection tube composed of two parts is used, place the upper part outside the lower part. Do not connect the cooker hood exhaust to the same conductor used to circulate hot air or evacuate fumes from other appliances generated by sources other than electrical. 4. Before proceeding with the assembly operations, remove the anti-grease filter(s) to make the unit easier to handle. If assembling the appliance in the suction version, prepare the hole for air evacuation. 5. Drill the holes according to the distances indicated and fix the appliance to the wall, aligning it in a horizontal position to the wall units. Use suitable screws and screw anchors for the type of wall. If screws and screw anchors are provided with the product, ensure they are suitable for the wall type. 6. Arrange the electrical power supply within the dimensions of the decorative flue. If the appliance is to be installed in the ducting version, prepare the air exhaust opening. Adjust the width of the support bracket of the upper flue and fix it to the ceiling using screws in line with the hood and respecting the distance from the ceiling indicated. 7. Connect the flange to the air exhaust hole using a connection pipe. Please note that these steps are a general guide and it is recommended to refer to the actual manual for detailed instructions specific to the Mastercook WK-Cristal exhaust hood.

What are the recommended maintenance operations for the Mastercook WK-Cristal exhaust hood?

To properly maintain the Mastercook WK-Cristal exhaust hood, follow these recommended maintenance operations: 1. Operating the appliance: It is recommended to operate the exhaust hood prior to cooking and leave it in operation for 15 minutes after cooking to completely eliminate cooking vapors and odors. 2. Cleaning the anti-grease filters: The anti-grease filters capture grease particles suspended in the air and can become clogged. Clean the filters every 2 months by removing them from the hood and washing them in a solution of water and neutral liquid detergent. Rinse thoroughly with warm water and let them dry. The filters can also be washed in the dishwasher. 3. Replacing the active carbon filters: The active carbon filters purify the air that is replaced in the environment. These filters are not washable or reusable and should be replaced every four months. The saturation of the active carbon filter depends on the frequency of use, type of cooking, and regular cleaning of the anti-grease filters. 4. Cleaning the fan and other surfaces: Regularly clean the fan and other surfaces of the cooker hood using a cloth moistened with denatured alcohol or non-abrasive liquid detergent. 5. Illumination maintenance: The illumination installation is designed for use during cooking and not for prolonged general illumination. If the bulb needs to be replaced, use only halogen lamps as the original. Please note that these are general maintenance operations for the Mastercook WK-Cristal exhaust hood. For detailed instructions and specific maintenance requirements, refer to the product manual.

How do I operate the Mastercook WK-Cristal exhaust hood prior to cooking?

To operate the Mastercook WK-Cristal exhaust hood prior to cooking, follow these steps: 1. Ensure that the electrical connection of the exhaust hood is properly installed and the power is turned on. 2. Before starting to cook, press the power button or switch to turn on the exhaust hood. 3. Adjust the desired extraction speed by pressing the corresponding speed control button. The exhaust hood may have multiple speed settings to choose from. 4. Position the cooking pots or pans on the stove under the exhaust hood. Make sure that the pots or pans are within the recommended distance from the hood to ensure effective ventilation. 5. Start cooking as usual. The exhaust hood will automatically start extracting the cooking vapors and odors from the air. 6. After cooking, leave the exhaust hood running for about 15 minutes to ensure that all cooking vapors and odors are properly eliminated. 7. Once you have finished cooking and the exhaust hood has been running for the recommended time, press the power button or switch to turn off the hood. Please note that these steps are a general guide for operating the Mastercook WK-Cristal exhaust hood prior to cooking. For detailed instructions and specific features of your particular model, refer to the product manual.

How do I clean the anti-grease filters of the Mastercook WK-Cristal exhaust hood?

To clean the anti-grease filters of the Mastercook WK-Cristal exhaust hood, follow these steps: 1. Remove the filters from the cooker hood. This can usually be done by unlocking or releasing the filters from their designated positions. 2. Prepare a solution of water and neutral liquid detergent. You can use a basin or sink to fill with the solution. 3. Place the filters in the solution and let them soak for a period of time. This will help to loosen and dissolve the grease particles trapped in the filters. 4. After soaking, use a soft brush or sponge to gently scrub the filters. Pay attention to areas with heavy grease buildup. 5. Rinse the filters thoroughly with warm water to remove any remaining detergent and grease. 6. Allow the filters to dry completely before reinstalling them back into the cooker hood. This will prevent any moisture from causing damage or mold growth. 7. If the filters are dishwasher-safe, you can also place them in the dishwasher for cleaning. Follow the manufacturer's instructions for dishwasher use. Remember to clean the anti-grease filters regularly, approximately every 2 months, to ensure optimal performance and prevent fire hazards.

How do I replace the active carbon filters of the Mastercook WK-Cristal exhaust hood?

To replace the active carbon filters of the Mastercook WK-Cristal exhaust hood, follow these steps: 1. Locate the active carbon filters in the exhaust hood. They are usually located behind or above the anti-grease filters. 2. Remove the anti-grease filters from the hood to access the active carbon filters. This can usually be done by unlocking or releasing the filters from their designated positions. 3. Take note of the position and orientation of the old active carbon filters. This will help ensure that the new filters are installed correctly. 4. Remove the old active carbon filters from their housing. They may be secured with clips or screws. Carefully detach them from the hood. 5. Take the new active carbon filters and insert them into the housing in the same position and orientation as the old filters. Make sure they are securely in place. 6. If there are any clips or screws, use them to secure the new filters in the housing. Ensure that they are tightly fastened. 7. Reinstall the anti-grease filters back into the hood, following the instructions provided in the manual. It is recommended to replace the active carbon filters every four months to maintain the effectiveness of the exhaust hood in purifying the air.

How do I clean the fan and other surfaces of the Mastercook WK-Cristal exhaust hood?

To clean the fan and other surfaces of the Mastercook WK-Cristal exhaust hood, follow these steps: 1. Prepare a cloth moistened with denatured alcohol or non-abrasive liquid detergent. 2. Gently wipe the fan blades and other surfaces of the cooker hood using the cloth. Pay attention to areas with grease or dirt buildup. 3. If necessary, use a soft brush or sponge to remove stubborn stains or debris from the surfaces. Be careful not to damage any delicate parts. 4. Continue wiping and cleaning until the fan and surfaces are free from grease, dirt, and stains. 5. Once cleaned, use a dry cloth to remove any excess moisture from the surfaces. 6. For the overhead light fixture, use a one-edged screwdriver or an appropriate tool to lift and remove the fixture. Replace the damaged lamp with a halogen lamp. 7. Avoid prolonged use of the illumination installation for general lighting purposes, as it may reduce the lifespan of the bulb. Regularly cleaning the fan and surfaces of the Mastercook WK-Cristal exhaust hood will help maintain its performance and appearance.

What should I do if the airflow of the Mastercook WK-Cristal exhaust hood is poor?

To improve the airflow of the Mastercook WK-Cristal exhaust hood, follow these steps: 1. Check if the aluminum grease filters are clogged. These filters capture grease particles and can become blocked over time. Clean the filters by removing them from the hood and washing them in a solution of water and neutral liquid detergent. Rinse them thoroughly with warm water and let them dry. Replace the filters when they are dry. 2. If the motor is running but there is no air flow, check if the charcoal filters are clogged. These filters purify the air and should be replaced every four months. Remove the old charcoal filters and install new ones according to the instructions provided. Ensure that the filters are securely in place. 3. Check if the butterfly valve is jammed. The butterfly valve controls the airflow and can become stuck due to debris or improper installation. Inspect the valve and remove any obstructions. Ensure that the valve moves freely. 4. If the high-temperature safety device is activated, it may be due to excessive heat in the hood. Make sure that the hood is installed at least 65cm away from the cooking stove to allow proper ventilation. 5. If the motor cuts off after a few minutes, it may indicate an issue with the hood's installation or electrical connection. Check the installation and ensure that the electrical supply is properly connected. If these troubleshooting steps do not resolve the issue, it is recommended to contact a technician for further assistance.

What should I do if the motor of the Mastercook WK-Cristal exhaust hood is running but there is no air flow?

If the motor of the Mastercook WK-Cristal exhaust hood is running but there is no air flow, you can try the following steps to troubleshoot the issue: 1. Check if the aluminum grease filters are clogged. If they are dirty or blocked, clean the filters by removing them from the hood and washing them in a solution of water and neutral liquid detergent. Rinse them thoroughly with warm water and let them dry. Replace the filters when they are dry. 2. Inspect the charcoal filters. If the exhaust hood is equipped with charcoal filters, check if they are clogged or saturated. Replace the charcoal filters according to the manufacturer's instructions. 3. Ensure that the butterfly valve is not jammed. The butterfly valve controls the airflow and can become stuck due to debris or improper installation. Check the valve and remove any obstructions. Ensure that the valve moves freely. 4. Verify if the high-temperature safety device is activated. If the hood is installed too close to the cooking stove, the high-temperature safety device may activate to prevent overheating. Ensure that the hood is installed at least 65cm away from the stove to allow proper ventilation. If these troubleshooting steps do not resolve the issue, it is recommended to contact a technician or the manufacturer's customer support for further assistance.

How can I eliminate strong cooking smells with the Mastercook WK-Cristal exhaust hood?

To eliminate strong cooking smells with the Mastercook WK-Cristal exhaust hood, follow these steps: 1. Before cooking, ensure that the exhaust hood is turned on and running at the appropriate speed. This will help to capture and remove cooking odors from the air. 2. Position your cooking pots or pans directly under the exhaust hood. This will allow the hood to effectively capture the cooking vapors and odors as they are produced. 3. Use the highest extraction speed setting on the exhaust hood when cooking dishes with strong odors. This will help to quickly remove the odors from the air. 4. After cooking, leave the exhaust hood running for an additional 10-15 minutes to ensure that all lingering cooking smells are eliminated. 5. Clean the anti-grease filters regularly to prevent the buildup of grease and odors. Remove the filters and wash them in a solution of water and neutral liquid detergent. Rinse thoroughly and let them dry before reinstalling. 6. If necessary, consider using additional odor-absorbing methods such as placing bowls of vinegar or baking soda near the cooking area to help neutralize odors. By following these steps, you can effectively eliminate strong cooking smells with the Mastercook WK-Cristal exhaust hood.

What should I do if the Mastercook WK-Cristal exhaust hood is making a whirring sound?

If the Mastercook WK-Cristal exhaust hood is making a whirring sound, you can try the following steps to address the issue: 1. Check for any objects or debris in contact with the fan blades. The whirring sound may be caused by something obstructing the rotation of the fan. Carefully inspect the area around the fan and remove any foreign objects that may be in contact with the blades. 2. If the whirring sound persists after removing any obstructions, it is recommended to contact a technician for further assistance. The issue may require professional inspection and repair. Please note that the whirring sound could be indicative of a mechanical or electrical problem, and attempting to fix it without proper knowledge or expertise may cause further damage. It is best to seek professional help to ensure the safe and proper functioning of the exhaust hood.

Is the manual of the Mastercook WK-Cristal available in English?

Yes, the manual of the Mastercook WK-Cristal is available in English .

Is your question not listed? Ask your question here

No results