Markbass MB7 Booster manual

Markbass MB7 Booster
(1)
  • Number of pages: 2
  • Filetype: PDF
LIMITED WARRANTY
Markbass oers an international limited warranty on Markbass products purchased from any
authorized Markbass dealer, eective from the day of purchase. The terms of this warranty
vary from country to country; please contact the Markbass distributor in your country for
details.
Please register this product online at www.markbass.it to establish the date of purchase.
However, please note that you are required to retain a copy of your receipt as proof of
purchase in order to receive warranty service.
This warranty does not apply to any damage to the product caused by misuse, mishandling,
accident, abuse, alteration, modication or unauthorized repairs. Product appearance and
normal wear and tear (worn paint, scratches, etc.) are not covered by this warranty. Markbass
reserves the right to be the sole arbiter regarding the misuse or abuse of this product.
Markbass assumes no liability for any incidental or consequential damages, which may result
from the failure of this product. Any warranties implied in fact or by law are limited to the
duration of this express limited warranty. Your legal rights related to the warranty will vary
depending on the country of purchase.
WARRANTY CARD
This product is guaranteed by the warranty provided in the country of purchase, under the
following conditions:
A - The Markbass warranty is only applicable if this document been properly completed (here
or online) and if the original invoice/bill of sale, mentioning model, serial number and
purchase date, is presented together with this document.
B - The obligations of Markbass are limited to the repair of defects. Warranty repair eligibility
will be decided at the sole discretion of Markbass or its representatives. Freight, freight
insurance costs, and any other costs related to the repair of this product are not covered by
this warranty.
C - All warranty repairs must be made by Markbass or an authorized Markbass (PARSEK)
service center.
D - This warranty does not apply in the following instances:
if the damage was caused by accident, negligence or modications; use of non Markbass
spare parts; or improper use, installation or packing;
• if the serial number on the equipment is illegible;
if the damage was caused by lightning, water, re, incorrect main voltage, insufficient
ventilation or any other cause beyond the control of Markbass.
E - Markbass reserves the right to redesign or improve/modify its product at any time without
any obligation to modify previously manufactured products.
Parsek srl. - Italy - 66020 San Giovanni Teatino (Ch) - Via Po, 52/A Tel. +39 085 446 37 55 - Fax
+39 085 440 77 64 - www.markbass.it - info@markbass.it
GETTING STARTED
BOOST -
To set up the Level Boost, plug your instrument into the Input Jack (5), and connect
the Output Jack (6) to your amplier, after connecting a +9/+12VDC power supply to the
DC IN (7) or powering the pedal with a standard 9V battery. Turn the boost on using the
right footswitch (3), making sure the LED on the Boost Level slider is ON (this indicates that
the eect is active). Next, adjust the Boost Level slider while toggling the footswitch (3) on
and o, comparing the volume of the direct signal with the boosted signal. Match the gain
level as closely as you can to the direct signal, then adjust the Level Boost slider to the
desired amount of added boost or cut. A suggested use of the boost is to leave it turned o
until it’s time to solo, then switch it on (3) for a quick level boost when you begin your solo.
You can easily apply this to ANY situation where you need two dierent, quickly accessible
playing volumes.
7-BAND GRAPHIC EQ -
To audition the EQ, rst step on the left footswitch (4), making sure
the LEDs on the EQ sections are ON (this indicates that the eect is active) and with the EQ
sliders (2) in at position (0 dB). Next, dial them in gradually one slider at a time to discover
how they aect your sound EQ, and tailor your bass tone the way you like it
.
TECHNICAL SPECS
INPUT IMPEDANCE:
1 Mohm / 6 Vpp
OUTPUT IMPEDANCE:
100 ohm / 6 Vpp
DRIVE:
+47dB (maximum gain)
TONE: from 300 Hz to 1.5 kHz
LEVEL OUTPUT: 0 to Max
GRAPHIC EQ: Freq. (Hz): 40, 80, 250, 400, 1200, 2000, 4000
LEVEL: (-16dB, +16dB)
POWER REQUIREMENTS- DC INPUT: +9/+12VDC or standard 9-volt battery
DIMENSIONS:
98.8 x 38.3 x 124.2 mm / 3.89” x 1.51” x 4.89”
WEIGHT:
420 g / 0.93 lbs
BLOCK DIAGRAM

OWNER’S MANUAL

In
booster
Level
Out
equalizer
40
80
250
400
1.2K
2K
4K
Markbass MB7 Booster

Need help?

Number of questions: 0

Do you have a question about the Markbass MB7 Booster or do you need help? Ask your question here. Provide a clear and comprehensive description of the issue and your question. The more detail you provide for your issue and question, the easier it will be for other Markbass MB7 Booster owners to properly answer your question.

View the manual for the Markbass MB7 Booster here, for free. This manual comes under the category Not categorized and has been rated by 1 people with an average of a 9. This manual is available in the following languages: English. Do you have a question about the Markbass MB7 Booster or do you need help? Ask your question here

Markbass MB7 Booster specifications

General
Brand Markbass
Model MB7 Booster
Product Not categorized
Language English
Filetype PDF
Features
Product type Effects pedal
Product colour Black
LED indicators
Product type Effects pedal
Product colour Black
Weight & dimensions
Width 98.8 mm
Depth 38.3 mm
Height 124.2 mm
Weight 420 g
Width 98.8 mm
Depth 38.3 mm
Height 124.2 mm
Weight 420 g
show more

Frequently Asked Questions

Below, you will find the most frequently asked questions about the Markbass MB7 Booster.

Is your question not listed? Ask your question here