Markbass MB Mini Boost manual

Markbass MB Mini Boost
(1)
  • Number of pages: 2
  • Filetype: PDF
LIMITED WARRANTY
Markbass oers an international limited warranty on Markbass products purchased from any
authorized Markbass dealer, eective from the day of purchase. The terms of this warranty
vary from country to country; please contact the Markbass distributor in your country for
details.
Please register this product online at www.markbass.it to establish the date of purchase.
However, please note that you are required to retain a copy of your receipt as proof of
purchase in order to receive warranty service.
This warranty does not apply to any damage to the product caused by misuse, mishandling,
accident, abuse, alteration, modication or unauthorized repairs. Product appearance and
normal wear and tear (worn paint, scratches, etc.) are not covered by this warranty. Markbass
reserves the right to be the sole arbiter regarding the misuse or abuse of this product.
Markbass assumes no liability for any incidental or consequential damages, which may result
from the failure of this product. Any warranties implied in fact or by law are limited to the
duration of this express limited warranty. Your legal rights related to the warranty will vary
depending on the country of purchase.
WARRANTY CARD
This product is guaranteed by the warranty provided in the country of purchase, under the
following conditions:
A - The Markbass warranty is only applicable if this document been properly completed (here
or online) and if the original invoice/bill of sale, mentioning model, serial number and
purchase date, is presented together with this document.
B - The obligations of Markbass are limited to the repair of defects. Warranty repair eligibility
will be decided at the sole discretion of Markbass or its representatives. Freight, freight
insurance costs, and any other costs related to the repair of this product are not covered by
this warranty.
C - All warranty repairs must be made by Markbass or an authorized Markbass (PARSEK)
service center.
D - This warranty does not apply in the following instances:
if the damage was caused by accident, negligence or modications; use of non Markbass
spare parts; or improper use, installation or packing;
• if the serial number on the equipment is illegible;
if the damage was caused by lightning, water, re, incorrect main voltage, insufficient
ventilation or any other cause beyond the control of Markbass.
E - Markbass reserves the right to redesign or improve/modify its product at any time without
any obligation to modify previously manufactured products.
Parsek srl. - Italy - 66020 San Giovanni Teatino (Ch) - Via Po, 52/A Tel. +39 085 446 37 55 - Fax
+39 085 440 77 64 - www.markbass.it - info@markbass.it
GETTING STARTED
BOOST - To set up the Level Boost, plug your instrument into the Input Jack (5), and
connect the Output Jack (6) to your amplier, after connecting a +9/+12VDC power
supply to the DC IN to the DC IN (7). Turn the boost on using the footswitch (3), making
sure the LED (4) is ON (this indicates that the eect is active). Next, adjust the Boost
Level slider while toggling the footswitch (3) on and o, comparing the volume of the
direct signal with the boosted signal. Match the gain level as closely as you can to the
direct signal, then adjust the Level Boost slider to the desired amount of added boost
or cut. A suggested use of the boost is to leave it turned o until its time to solo, then
switch it on (3) for a quick level boost when you begin your solo. You can easily apply
this to ANY situation where you need two dierent, quickly accessible playing volumes.
VPF (Variable Pre-shape Filter) - This lter boosts lows and highs, and cuts mids.
Some call this kind of eect a scoop, a smiley-shape EQ, or an enhance knob. Its very
eective for slap bass, pick playing, and driving eighth-note rock. It’s o when it is all
the way counterclockwise—we suggest you start in that position and turn the lter up
gradually, to hear and understand what it does.
TECHNICAL SPECS
INPUT IMPEDANCE: 1 Mohm / 6 Vpp
OUTPUT IMPEDANCE: 470 ohm / 6 Vpp
BOOST: 0 to +20dB (maximum gain)
POWER REQUIREMENTS- DC INPUT: +9/+12VDC
DIMENSIONS: 48.4 x 38.2 x 104.2 mm
1.91” x 1.5” x 4.1”
WEIGHT: 174 g
0.38 lbs
BLOCK DIAGRAM
In
booster
Level VPF
Out

OWNER’S MANUAL

Markbass MB Mini Boost

Need help?

Number of questions: 0

Do you have a question about the Markbass MB Mini Boost or do you need help? Ask your question here. Provide a clear and comprehensive description of the issue and your question. The more detail you provide for your issue and question, the easier it will be for other Markbass MB Mini Boost owners to properly answer your question.

View the manual for the Markbass MB Mini Boost here, for free. This manual comes under the category Not categorized and has been rated by 1 people with an average of a 9. This manual is available in the following languages: English. Do you have a question about the Markbass MB Mini Boost or do you need help? Ask your question here

Markbass MB Mini Boost specifications

General
Brand Markbass
Model MB Mini Boost
Product Not categorized
Language English
Filetype PDF
Features
Product type Effects pedal
Product colour Black,Yellow
LED indicators
Product type Effects pedal
Product colour Black,Yellow
Weight & dimensions
Width 48.4 mm
Depth 38.2 mm
Height 105.2 mm
Weight 230 g
Width 48.4 mm
Depth 38.2 mm
Height 105.2 mm
Weight 230 g
show more

Frequently Asked Questions

Below, you will find the most frequently asked questions about the Markbass MB Mini Boost.

Is your question not listed? Ask your question here