Makita HM1307C manual

Makita HM1307C
9.8 · 1
PDF manual
 · 44 pages
English
manualMakita HM1307C
2
12
34
56
78
ON
OFF
ON I
OFF 0
1
2
3
4
5
6
7
8
9
10
11
12
8
9
10
13
14
8
9
10
13
14

Manual

View the manual for the Makita HM1307C here, for free. This manual comes under the category drill machines and has been rated by 1 people with an average of a 9.8. This manual is available in the following languages: English. Do you have a question about the Makita HM1307C or do you need help? Ask your question here

Need help?

Do you have a question about the Makita and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Makita HM1307C specifications

Below you will find the product specifications and the manual specifications of the Makita HM1307C.

General
BrandMakita
ModelHM1307C | HM1307C
Productdrill machine
LanguageEnglish
FiletypeUser manual (PDF)

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Makita HM1307C below.

How do I remove rust from my Makita drill machine?

1. Soak the rusty part in vinegar until completely soaked through. 2. Let the vinegar work on the rust for 24 hours. 3. Remove the rust with a wire brush or aluminium foil.

What does '16V' or '20V' mean?

The maximum achievable charge level is expressed with 16V or 20V. The V in this case stands for Volt.

Do I have to wear hearing protection when using a drill machine?

The amount of sound varies a lot per brand and type of drill machine, it is therefore wise to wear hearing protection to be sure.

How do I troubleshoot if the Makita HM1307C drill machine is not chipping or scaling properly?

To troubleshoot if the Makita HM1307C drill machine is not chipping or scaling properly, follow these steps: 1. Ensure proper grip and pressure: Always use the side grip (auxiliary handle) and firmly hold the tool by both the side grip and switch handle during operations. Apply slight pressure on the tool to prevent uncontrolled bouncing. Avoid pressing too hard, as it does not increase efficiency. 2. Check the bit retention: Make sure the bit is securely retained in the tool holder. Insert the bit into the holder as far as it will go and pivot the tool retainer downward toward the barrel to securely retain the bit. To remove the bit, follow the installation procedure in reverse. 3. Verify the adjusting dial setting: Check the number on the adjusting dial to ensure it is set appropriately for the desired chipping or scaling function. The number corresponds to the blows per minute (BPM) of the tool. Adjust the dial to the desired setting for optimal performance. 4. Inspect the bit condition: Examine the condition of the bit for any signs of wear or damage. Replace the bit if it is worn out or damaged, as it may affect the chipping or scaling performance. 5. Consult the manual: If the issue persists, refer to the manual for further troubleshooting steps or contact Makita Authorized Service Centers for assistance. By following these steps, you can troubleshoot and address issues related to the chipping or scaling performance of the Makita HM1307C drill machine.

What should I do if the Makita HM1307C drill machine is not starting or has a weak power output?

If the Makita HM1307C drill machine is not starting or has a weak power output, you can troubleshoot the issue by following these steps: 1. Check the power source: Ensure that the drill machine is properly connected to a functioning power outlet. Verify that the power cord is not damaged or frayed. 2. Verify the switch position: Make sure the switch lever is in the "ON (I)" position. If it is in the "OFF (O)" position, switch it to the "ON (I)" position to start the tool. 3. Inspect the carbon brushes: Over time, the carbon brushes in the motor can wear out and affect the power output. Check the condition of the carbon brushes and replace them if they are worn down or damaged. 4. Clean the air vents: Dust and debris can accumulate in the air vents, restricting airflow and causing the tool to overheat. Use a soft brush or compressed air to clean the vents and ensure proper ventilation. 5. Consult the manual: If the issue persists, refer to the manual for further troubleshooting steps or contact Makita Authorized Service Centers for assistance. By following these steps, you can troubleshoot and address the issue of the Makita HM1307C drill machine not starting or having a weak power output.

How can I troubleshoot if the Makita HM1307C drill machine is overheating during operation?

To troubleshoot if the Makita HM1307C drill machine is overheating during operation, follow these steps: 1. Check for proper ventilation: Ensure that the air vents of the drill machine are not blocked or obstructed. Clean any dust or debris that may have accumulated in the vents using a soft brush or compressed air. 2. Reduce workload: If the drill machine is being used for extended periods or on heavy-duty tasks, consider reducing the workload or taking breaks to allow the tool to cool down. 3. Verify power supply: Ensure that the drill machine is connected to a stable power supply. Fluctuations or low voltage can cause the tool to overheat. If necessary, use a voltage stabilizer or connect to a different power outlet. 4. Inspect carbon brushes: Over time, the carbon brushes in the motor can wear out and affect the tool's performance. Check the condition of the carbon brushes and replace them if they are worn down or damaged. 5. Consult the manual: If the issue persists, refer to the manual for further troubleshooting steps or contact Makita Authorized Service Centers for assistance. By following these steps, you can troubleshoot and address the issue of the Makita HM1307C drill machine overheating during operation.

What should I check if the Makita HM1307C drill machine is producing excessive noise?

If the Makita HM1307C drill machine is producing excessive noise, you can check the following: 1. Tighten all screws and bolts: Ensure that all screws and bolts on the drill machine are securely tightened. Loose components can cause vibrations and generate excessive noise during operation. 2. Inspect the bit condition: Examine the condition of the bit for any signs of wear or damage. A worn-out or damaged bit can cause irregular vibrations and noise. Replace the bit if necessary. 3. Verify the bit installation: Make sure the bit is properly installed and securely retained in the tool holder. Follow the installation procedure in the manual to ensure correct placement and retention. 4. Check for debris or obstructions: Inspect the chuck and bit area for any debris, such as wood chips or dust, that may be causing interference. Clean out any obstructions to ensure smooth operation. 5. Consult the manual: If the issue persists, refer to the manual for further troubleshooting steps or contact Makita Authorized Service Centers for assistance. By following these steps, you can check and address potential causes of excessive noise in the Makita HM1307C drill machine.

How do I address excessive vibration in the Makita HM1307C drill machine during use?

To address excessive vibration in the Makita HM1307C drill machine during use, follow these steps: 1. Check the bit condition: Inspect the condition of the bit for any signs of wear or damage. A worn-out or damaged bit can cause increased vibration. Replace the bit if necessary. 2. Verify the bit installation: Ensure that the bit is properly installed and securely retained in the tool holder. Follow the installation procedure in the manual to ensure correct placement and retention. 3. Adjust the work mode: The HM1307C drill machine offers different work modes for various applications. Experiment with different work modes to find the one that minimizes vibration for your specific task. 4. Use proper technique: Maintain a firm grip on the drill machine, using both the side grip (auxiliary handle) and the switch handle. Apply steady pressure without excessive force to prevent unnecessary vibration. 5. Consult the manual: If the issue persists, refer to the manual for further troubleshooting steps or contact Makita Authorized Service Centers for assistance. By following these steps, you can address excessive vibration in the Makita HM1307C drill machine during use and ensure smoother operation.

Is the manual of the Makita HM1307C available in English?

Yes, the manual of the Makita HM1307C is available in English .

Is your question not listed? Ask your question here

No results