Makita ADP05 manual

Makita ADP05
8.8 · 1
PDF manual
 · 1 page
English
manualMakita ADP05

ENGLISH (Original instructions)

SYMBOLS

.........Read instructions.
.......Only for EU countries
Do not dispose of electric
equipment or battery pack
together with household waste
material!
In observance of the
European Directives, on
Waste Electric and Electronic
Equipment and Batteries and
Accumulators and Waste
Batteries and Accumulators
1
3
and their implementation in
accordance with national
laws, electric equipment and
batteries and battery pack(s)
that have reached the end
of their life must be collected
separately and returned to an
environmentally compatible
recycling facility.

SAFETY INSTRUCTIONS

Important safety instructions for
battery cartridge
Recharge only with the charger
speciedbythemanufacturer.A
charger that is suitable for one type of
batterypackmaycreateariskofre
when used with another battery pack.
Usetheproductonlywithspecically
designated battery packs. Use of any
other battery packs may create a risk
ofinjuryandre.
Before using battery cartridge, read all
instructions and cautionary markings
on (a) battery charger, (b) battery, and
(c) product using battery.
Do not disassemble battery cartridge.
If operating time has become
excessively shorter, stop operating
immediately. It may result in a risk of
overheating, possible burns and even
an explosion.
Under abusive conditions, liquid may
be ejected from the battery; avoid
contact. If electrolyte gets into your
eyes, rinse them out with clear water
and seek medical attention right away.
It may result in loss of your eyesight.
Do not short the battery cartridge:
1. Do not touch the terminals with any
conductive material.
When not using or after charging,
remove the USB cable and close the
cover.
battery holder, causing injury to you or
someone around you.
Do not install the battery cartridge
forcibly. If the cartridge does not slide in
easily, it is not being inserted correctly.
To remove the battery cartridge, slide it
from the product while sliding the button
(3) on the front of the cartridge.

CONNECTING USB DEVICE

(Fig. 2)

CAUTION:
Connect only devices which are
compatible with DC5V, 2.1A power
source to the USB power supply port.
Otherwise it may cause malfunction to
the product.
Connect the USB cable (not included)
with the power supply port (4) of the
product. And then connect the other end
of the cable with the device.
You can also hang the product on your
belt.
NOTE:
Before connecting USB device to the
product, always backup your data of
USB device. Otherwise your data may
lose by any possibility.
The product may not supply power to
some USB devices.
Do not insert a nail, wire, etc. into USB
power supply port. Otherwise a circuit
shortmaycausesmokeandre.
Wait for 10 seconds before charging
another device consecutively.
On rare occasions, the tool may not
start charging due to the protection
system to reduce battery consumption.
In that case, remove the USB cable,
and reconnect it after approximately
10 seconds.
2. Avoid storing battery cartridge in a
container with other metal objects
such as nails, coins, etc.
3. Do not expose battery cartridge to
water or rain.
A battery short can cause a large
currentow,overheating,possible
burns and even a breakdown.
Do not store the product and battery
cartridge in locations where the
temperature may reach or exceed
50°C (122°F).
Do not incinerate the battery cartridge
even if it is severely damaged or is
completely worn out. The battery
cartridgecanexplodeinare.
Be careful not to drop or strike battery.
Do not use a damaged battery.
Follow your local regulations relating
to disposal of battery.
Tips for maintaining maximum
battery life
Never recharge a fully charged battery
cartridge. Overcharging shortens the
battery service life.
Charge the battery cartridge with room
temperature at 10°C - 40°C (50°F -
104°F).
Let a hot battery cartridge cool down
before charging it.
Charge the battery cartridge if you do
not use it for a long period (more than
six months).
For an optimum life-time, the battery
cartridge has to be fully charged, after
use.

SAVE THESE INSTRUCTIONS.

2
4

SPECIFICATIONS

Model ADP05
USB
power
supply
Ports 2 (USB A type)
Output
voltage
DC 5V
Output
current
2.1A (each ports)
(4.2A in total)
Input
rating
14.4 - 18V DC,
5A max.
Max. operating
temperature
40 degree C
Battery cartridge
BL1415, BL1415N,
BL1430, BL1440,
BL1450, BL1815,
BL1815N, BL1820,
BL1820B, BL1830,
BL1840, BL1840B,
BL1850, BL1850B
Weight (without
battery)
0.11 kg (0.2 lbs)
Due to our continuing program of
research and development, the
specicationshereinaresubjectto
change without notice.
Specicationsmaydifferfromcountry
to country.

INSTALLING OR REMOVING

BATTERY CARTRIDGE (Fig. 1)

To install the battery cartridge (1), align
the tongue on the battery cartridge with
the groove in the product and slip it into
place. Insert it all the way until it locks in
place with a little click. If you can see the
red indicator (2) on the upper side of the
button, it is not locked completely.
Always install the battery cartridge fully
until the red indicator cannot be seen.
If not, it may accidentally fall out of the
1
2
3
4

ADP05

1
2

Makita Corporation

3-11-8, Sumiyoshi-cho,
Anjo, Aichi, Japan
www.makita.com
ALA
ADP05-NA3-0415

Manual

View the manual for the Makita ADP05 here, for free. This manual comes under the category not categorized and has been rated by 1 people with an average of a 8.8. This manual is available in the following languages: English. Do you have a question about the Makita ADP05 or do you need help? Ask your question here

Need help?

Do you have a question about the Makita and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Makita ADP05 specifications

Below you will find the product specifications and the manual specifications of the Makita ADP05.

The Makita ADP05 is a power source designed to turn your Makita lithium-ion battery into a charging port. This product includes two USB charging ports, each delivering a 2.1A output. The device is compatible with Makita lithium-ion batteries and has a built-in clip for easy attachment to a belt or holster, enhancing portability. The ADP05 has a durable construction with rubber covers for added protection. With a weight of 0.11 kg (0.2 lbs) without the battery, the ADP05 is lightweight and convenient to carry around. The specifications of the product include an input rating of 14.4 - 18V DC, 5A max, with an output voltage of DC 5V. The device is compatible with various Makita battery cartridges. The user manual provides important safety instructions for the battery cartridge, emphasizing the need to recharge only with the specified charger and the importance of following instructions to prevent injury or damage. Additionally, it includes tips for maintaining maximum battery life to ensure optimal performance. In conclusion, the Makita ADP05 is a practical and efficient accessory for Makita lithium-ion batteries, providing convenient USB charging ports on the go.

General
BrandMakita
ModelADP05 | ADP05
Productnot categorized
LanguageEnglish
FiletypeUser manual (PDF)
Packaging data
Quantity per pack1 pc(s)
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Makita ADP05 below.

Is the manual of the Makita ADP05 available in English?

Yes, the manual of the Makita ADP05 is available in English .

Is your question not listed? Ask your question here

No results