Liebherr TP 1424 manual

Liebherr TP 1424
6.5 · 2
PDF manual
 · 14 pages
English
manualLiebherr TP 1424

5.1.1 Food refrigeration

u
Store perishable food such as ready-to-serve dishes, meat
products and sausages in the coldest zone. Place butter and
preserves in the upper area and in the door (see Appliance
at a glance).
u
Use recyclable plastic, metal, aluminium and glass
containers and cling film for wrapping.
u
Always store liquids and food which is subject to odour or
taste transfer in closed containers or cover them.
u
Do not store food too close together to enable good air
circulation.
u
To safeguard bottles from tipping over: move the bottle
holder.

5.1.2 Setting the temperature

The temperature can be set between 1 (warmest temperature,
minimum cooling performance) and 7 (coldest temperature,
maximum cooling performance).
The middle control setting is recommended, then a middle
temperature of approx.5 °C is established in the refrigerator
compartment.
To ensure ideal temperatures for storing frozen foods, a setting
of “4” to “7” on the temperature controller is recommended.
Selecting “7” makes it possible to achieve temperatures under
0 °C in the coldest part of the fridge compartment.
An average temperature of approx. –18 °C is then established
in the freezer compartment
u
Turn the temperature control
Fig. 3 (1)
.
The temperature depends on the following factors:
- the door opening frequency
- the room temperature at the site where the appliance is
installed
- the type, temperature and quantity of frozen food
u
Adjust the temperature as needed, using the control.

5.1.3 CoolPlus function*

At low room temperatures of 18 °C or lower:
u
Press the Cool-Plus switch
Fig. 3 (2)
.
w
The deep temperatures in the freezer compartment are
ensured.
Once the room temperature is again higher than18 °C :
u
Deactivate the Cool-Plus
Fig. 3 (2)
switch manually.
Note
u
At normal room temperatures, in excess of 18 °C, the Cool-
Plus switch should be turned off, as it is not required.

5.1.4 Shelves

Moving or removing shelves

CAUTION

Danger of laceration!
The shelf may break. The broken fragments may cause lacera-
tion.
u
Remove only empty shelves.
The shelves have stops preventing them from being uninten-
tionally pulled out.
Fig. 11
u
Lift the shelf slightly and pull forward a little.
u
Adjust the height of the shelf. To do so, push the cut-outs
along the supports.
u
In order to remove the shelf fully, place it at a slant and pull
out towards the front.
u
Insert shelf with the raised edge pointing upwards at the
back.
w
The food does not freeze onto the rear wall.
Dismantling shelves
u
The shelves can be disman-
tled for cleaning.

5.1.5 Using the sectioned shelf

CAUTION

Danger of laceration!
The shelf may break. The broken fragments may cause lacera-
tion.
u
Remove only empty shelves.
Fig. 12
*
u
The glass shelf with stop face (2) has to be at the back.*
u
The glass plate (1) with pull-out stops must be at the front so
that the stops (3) face downwards.*
Adjusting the height:
u
Pull the glass plates out forwards one by one.*
u
Remove the support from the catch mechanism and click
into place at the required height.*
Using both shelves:
u
Lift the top glass plate and pull the bottom glass plate
forwards.*

5.1.6 Door racks

Removing the storage rack
u
Remove storage rack according to
illustration.
*

Control

8 * Depending on model and options

Manual

View the manual for the Liebherr TP 1424 here, for free. This manual comes under the category refrigerators and has been rated by 2 people with an average of a 6.5. This manual is available in the following languages: English. Do you have a question about the Liebherr TP 1424 or do you need help? Ask your question here

Need help?

Do you have a question about the Liebherr and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Liebherr TP 1424 specifications

Below you will find the product specifications and the manual specifications of the Liebherr TP 1424.

General
BrandLiebherr
ModelTP 1424 | TP 1424
Productrefrigerator
EAN4016803030379
LanguageEnglish
FiletypeUser manual (PDF)
Design
Appliance placementFreestanding
Product colorWhite
Door hingeRight
Reversible doorsYes
Control typeRotary
Child lockNo
Built-in displayNo
Shelves materialTempered glass
Housing materialSteel
Power
Power sourceElectric
Annual energy consumption141 kWh
Energy usage0.38 kWh/24h
Connected load- W
AC input voltage220 - 240 V
AC input frequency50 Hz
Current0.8 A
Energy efficiency scaleA to G
Energy efficiency classE
Performance
Noise level38 dB
Total net capacity121 L
Total gross capacity127 L
Climate classSN-ST
C
Fridge
Fridge net capacity106 L
Fridge gross capacity112 L
Automatic defrost (fridge)Yes
Fridge interior lightYes
Lamp typeLED
Egg balconyYes
Number of vegetable drawers1
Multi-Airflow system (fridge)No
Fridge number of shelves/baskets2
Fridge door balconies3
Freezer
Freezer positionTop-placed
Freezer net capacity15 L
Freezer gross capacity- L
Storage time during power failure10 h
Freezing capacity2 kg/24h
No Frost (freezer)-
Star rating4*
Freezer number of shelves/baskets1
Weight & dimensions
Width501 mm
Depth620 mm
Height850 mm
Weight37300 g
Depth with door open534 mm
Width with door open1072 mm
Packaging data
Package width517 mm
Package depth711 mm
Package height911 mm
Package weight40000 g
Ergonomics
Adjustable feetYes
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Liebherr TP 1424 below.

How do I prevent drops from forming on the glass plates of my fridge?

There may be various causes for this, it is recommended to check the following: - Is the drain hole free of dirt? - Does the refrigerator door close properly? - Is the refrigerator not too full so that air can circulate properly? - Is the temperature not set below 5 degrees?

What do I do about a smelly fridge?

A common method for solving the problem of a smelly fridge is to pour vinegar into the drain and temporarily place a cup of vinegar in the fridge.

How much free space does my fridge need?

A minimum of 2.5 centimetres of free space around the fridge is needed to ventilate properly.

What does R-410A stand for?

R-410A is a refrigerant used in machines that cool to zero degrees Celsius.

What is the weight of the Liebherr TP 1424?

The Liebherr TP 1424 has a weight of 37300 g.

What is the height of the Liebherr TP 1424?

The Liebherr TP 1424 has a height of 850 mm.

What is the width of the Liebherr TP 1424?

The Liebherr TP 1424 has a width of 501 mm.

What is the depth of the Liebherr TP 1424?

The Liebherr TP 1424 has a depth of 620 mm.

What energy label does the Liebherr TP 1424 have?

The Liebherr TP 1424 has energy label E.

Does the Liebherr TP 1424 have reversible doors?

Yes, the Liebherr TP 1424 has reversible doors. This means that the user can easily change the position of the door hinge, allowing for flexible placement options in the kitchen.

What is the annual energy consumption of the Liebherr TP 1424?

The annual energy consumption of the Liebherr TP 1424 is 141 kWh. This indicates that the refrigerator is energy-efficient and can help the user save on electricity bills compared to other models with higher energy consumption.

How much noise does the Liebherr TP 1424 produce?

The Liebherr TP 1424 has a noise level of 38 dB. This is relatively low, ensuring quiet operation and minimizing disturbance for the user.

What is the total net capacity of the Liebherr TP 1424?

The total net capacity of the Liebherr TP 1424 is 121 L. This provides ample storage space for the user to store their food and groceries.

How tall is the packaging of the Liebherr TP 1424?

The packaging height of the Liebherr TP 1424 is 911 mm. This information is useful for the user to determine whether the refrigerator will fit properly through doorways and hallways during delivery.

How do I adjust the temperature settings of the Liebherr TP 1424 refrigerator?

To adjust the temperature settings of the Liebherr TP 1424 refrigerator, follow these steps: 1. Locate the temperature control dial. It is usually located inside the refrigerator compartment. 2. Turn the temperature control dial to adjust the temperature. The dial may have numbers or symbols indicating different temperature levels. For example, a range from 1 to 7 may be provided, with 1 being the warmest temperature and 7 being the coldest temperature. 3. Set the temperature according to your preference. A middle control setting is recommended, which typically results in a refrigerator compartment temperature of around 5°C. 4. Consider factors such as the frequency of door openings, the room temperature where the refrigerator is installed, and the type, temperature, and quantity of frozen food stored. 5. If you need to achieve lower temperatures in the freezer compartment, select a higher temperature setting, such as 4 to 7 on the temperature control dial. 6. Optionally, if the room temperature is 18°C or lower, you can activate the CoolPlus function by pressing the Cool-Plus switch. This ensures lower temperatures in the freezer compartment. Remember to deactivate the CoolPlus function when the room temperature rises above 18°C. 7. Monitor the temperature inside the refrigerator and adjust the temperature control dial as needed to maintain the desired temperature. By following these steps, you can easily adjust the temperature settings of the Liebherr TP 1424 refrigerator to suit your needs.

What should I do if the temperature inside the refrigerator is not reaching the desired level?

If the temperature inside the Liebherr TP 1424 refrigerator is not reaching the desired level, you can try the following steps to troubleshoot the issue: 1. Check the temperature control settings: Ensure that the temperature control dial is set to the desired temperature. Adjust the dial if necessary and wait for a few hours to see if the temperature stabilizes. 2. Verify proper airflow: Make sure that there is enough space around the refrigerator for proper airflow. Clear any obstructions that may be blocking the vents or air circulation. 3. Check the door seal: Inspect the door seal for any damage or gaps. A faulty door seal can cause temperature fluctuations. If needed, clean the seal and ensure it is properly aligned and sealing tightly. 4. Avoid overloading the refrigerator: Overloading the refrigerator with too much food can restrict airflow and affect temperature distribution. Remove any unnecessary items or redistribute the contents to allow for better air circulation. 5. Minimize door openings: Limit the frequency and duration of door openings to prevent warm air from entering the refrigerator. This can help maintain a consistent temperature. If the issue persists after following these steps, it is recommended to contact the manufacturer's customer support for further assistance.

How often should I clean the storage compartments of the Liebherr TP 1424 refrigerator?

To ensure proper maintenance and cleanliness of the storage compartments in the Liebherr TP 1424 refrigerator, follow these guidelines: 1. Regular cleaning: Clean the storage compartments of the refrigerator regularly to maintain hygiene and prevent the buildup of dirt, spills, and odors. Aim to clean the compartments at least once every three months or as needed. 2. Empty the compartments: Before cleaning, remove all food items and shelves from the compartments. This allows for easier access and thorough cleaning. 3. Use mild detergent: Prepare a solution of warm water and a mild detergent. Dampen a soft cloth or sponge with the solution and gently wipe the interior surfaces of the compartments. Pay attention to corners, crevices, and removable parts. 4. Remove and clean shelves and drawers: Take out the shelves and drawers from the compartments and wash them separately with the mild detergent solution. Rinse them thoroughly and allow them to dry completely before placing them back into the compartments. 5. Clean the door seals: Wipe the door seals with a damp cloth to remove any dirt or residue. Ensure that the seals are clean and free from debris to maintain a proper seal and prevent air leakage. 6. Dry the compartments: After cleaning, use a clean, dry cloth to wipe the compartments and remove any excess moisture. This helps prevent the growth of mold or mildew. 7. Reassemble and restock: Once the compartments are dry, reassemble the shelves and drawers and place the food items back into the compartments. By following these steps, you can keep the storage compartments of the Liebherr TP 1424 refrigerator clean and maintain optimal conditions for storing your food.

What should I do if the refrigerator is not cooling properly?

If the Liebherr TP 1424 refrigerator is not cooling properly, you can try the following steps to troubleshoot the issue: 1. Check the power and settings: - Ensure that the refrigerator is properly plugged into a functioning power outlet. - Verify that the temperature control dial is set to the appropriate cooling level. 2. Clean the condenser coils: - Locate the condenser coils, usually located at the back or bottom of the refrigerator. - Use a vacuum cleaner or a soft brush to remove any dust or debris from the coils. - Cleaning the coils improves the efficiency of the refrigerator's cooling system. 3. Check the door seal: - Inspect the door seal for any damage or gaps. - A faulty door seal can cause warm air to enter the refrigerator, affecting its cooling performance. - If necessary, clean the seal and ensure it is properly aligned and sealing tightly. 4. Ensure proper ventilation: - Make sure that the refrigerator has enough space around it for proper airflow. - Clear any obstructions that may be blocking the ventilation grilles or vents. 5. Avoid overloading the refrigerator: - Overloading the refrigerator with too much food can restrict airflow and impact cooling. - Remove any unnecessary items or redistribute the contents to allow for better air circulation. 6. Monitor the temperature: - Keep an eye on the temperature inside the refrigerator using a thermometer. - If the temperature does not reach the desired level, consider contacting customer service for further assistance. If the issue persists after following these steps, it is recommended to contact the manufacturer's customer service for professional support and guidance.

What is the specified ambient temperature range for the Liebherr TP 1424 refrigerator?

The specified ambient temperature range for the Liebherr TP 1424 refrigerator is mentioned in the manual. However, I couldn't find the specific page that contains this information. As an alternative solution, I recommend the following steps: 1. Visit the official website of Liebherr: Go to the Liebherr website using a web browser. 2. Navigate to the "Products" or "Refrigerators" section: Look for the section that lists the different types of products or specifically refrigerators. 3. Locate the Liebherr TP 1424 refrigerator: Browse through the available refrigerators or use the search function to find the Liebherr TP 1424 model. 4. Click on the product details: Once you find the Liebherr TP 1424 refrigerator, click on its name or image to access the detailed product information. 5. Look for the specifications: Within the product details page, search for a section that provides the specifications or technical details of the refrigerator. 6. Find the ambient temperature range: Look for the information related to the ambient temperature range in the specifications. It should mention the minimum and maximum temperatures within which the refrigerator is designed to operate effectively. If you are unable to find the specific information on the website, I recommend reaching out to Liebherr's customer support for further assistance. They will be able to provide you with the necessary details regarding the ambient temperature range for the Liebherr TP 1424 refrigerator.

How do I install the Liebherr TP 1424 refrigerator with wall spacers?

To install the Liebherr TP 1424 refrigerator with wall spacers, follow these steps: 1. Remove the spacer from under the left-hand side of the door. 2. If your refrigerator has a door handle, follow the sequence of item numbers in the diagram provided in the manual. 3. If your refrigerator does not have a door handle, refer to the diagram specific to appliances without a door handle. 4. If your refrigerator has a freezer compartment, refer to the diagram specific to appliances with a freezer compartment. 5. Insert the spacer back under the right-hand side of the door for stability. 6. Ensure that the bearing parts are securely screwed into place to prevent the door from dropping out. 7. Check all screws and retighten if necessary. 8. For undercounter installation, be cautious not to crush or damage the mains power cable. 9. Ensure that the plug is easily accessible and not located behind the appliance. 10. Provide a minimum ventilation cavity of 140 cm2 at the rear of the appliance for proper ventilation. 11. If installing the refrigerator into a row of kitchen units, follow the instructions provided in the manual. 12. Dispose of the packaging materials properly at an official collecting point. 13. Connect the appliance to a properly earthed and fused socket. 14. Switch on the appliance by turning the temperature control dial to the appropriate setting. By following these steps, you can successfully install the Liebherr TP 1424 refrigerator with wall spacers.

What should I do if there is a leak in the refrigerant circuit of the Liebherr TP 1424 refrigerator?

If there is a leak in the refrigerant circuit of the Liebherr TP 1424 refrigerator, it is important to take the following steps: 1. Safety precautions: Ensure your safety by avoiding direct contact with the refrigerant and following the guidelines provided in the manual. 2. Ventilate the area: If a leak occurs, remove any naked flames or sources of ignition from the vicinity. Open windows and doors to ventilate the room well. 3. Contact customer service: Notify the after-sales service or customer support of Liebherr immediately to report the leak and seek professional assistance. 4. Do not attempt repairs: It is crucial not to attempt any repairs or interventions in the refrigerant circuit yourself. Leave this task to trained professionals who have the expertise and knowledge to handle such situations safely. By following these steps, you can ensure your safety and take the necessary actions to address a refrigerant circuit leak in the Liebherr TP 1424 refrigerator.

Is the manual of the Liebherr TP 1424 available in English?

Yes, the manual of the Liebherr TP 1424 is available in English .

Is your question not listed? Ask your question here

No results