Lastolite Cubelite LiteTable manual

Lastolite Cubelite LiteTable
(1)
  • Number of pages: 3
  • Filetype: PDF
1. Remove items from the box. You should have:
- Bag containing the LiteTable (flat)
- 4 x Black support rods
- 4 x joining clips for the rods
- Back frame rod assembly
- Circular acrylic sheet
- Roll of translucent film
- Fabric back drop
Remove the LiteTable from the protective bag.
2. Lay the LiteTable on the floor and position the end of
one of the rods on the corner of the lower steel rim.
Ensure the steel rim locates into the jaws of the tip at
the end of the rod.
3. Pull the two steel rims away from each other and locate
the jaws of the tip at the other end of the rod into the
upper rim.
4. Repeat steps 2&3 for the remaining three corners.
When all four rods are in place, check they are all in a
vertical position.
5. Place the circular acrylic sheet on the top of the
LiteTable (Take care not to drop this as it will break).
6. The base unit is now complete.
7. Take hold of the back frame rod assembly and allow
the rods to ‘snap’ into position. This will form one
complete ‘U’ shaped structure.
8. Ensure that all the ‘Silver joints are fully inserted into
the hollow black support rods.
9. Position the LiteTable so that the rear opening is in
front of you. Line the back frame assembly up with the
two rear support rods on the LiteTable base unit.
10. Use the four joining clips to attach the rods together.
Place one two inches from the bottom and one two
inches from the top of each of the rear support rods
on the LiteTable base unit. The clips simply snap shut
around the rod. Then attach the back frame assembly
in the same way.
11. The back frame assembly is now in place
12. Take the fabric back drop and with the smooth side
facing the front, wrap the top edge over the the
crossbar on the back frame structure and attach to the
velcro. This should leave a velcro strip facing forward
across the top of the back frame.
13. Unroll the translucent film. Then attach the velcro strip
at one end of the film to the velcro strip at the top of
the back frame. Allow the film to drop onto the top of
the base unit creating an infinity curve.
14. Take the bottom of the fabric back drop and ensure it
lays over the top of the black rim on the edge of the
LiteTable base unit (do not let it hang down the back of
the base unit). This ensures the black edge cannot be
seen through the translucent film.
15. Add your chosen lighting system. Refer to the label
near the rear opening of the LiteT
able for advice on
how to position the light source inside.
Breaking Down your LiteTable kit.
16. Remove the translucent film, roll up and return to tube.
17. Remove and roll up the fabric back drop. This can also
go in the tube with the film for protection.
18. Disconnect the back frame assembly from the support
rods. To dismantle the frame pull the rods apart and
fold them so they cannot ‘snap’ back into position.
19. Remove the circular acrylic sheet from the top of the
base unit and return it to the protective bag.
20. Remove the supporting rods from the base unit and
allow the two steel rims of the LiteT
able to lie on top
of each other. Return them to the protective bag.
21. Return all the items to the storage box.

Setting up your LiteTable

1 2 3
4 5 6
7 8 9
10 11 12
13 14 15
A
02.07
Lastolite Cubelite LiteTable

Need help?

Number of questions: 0

Do you have a question about the Lastolite Cubelite LiteTable or do you need help? Ask your question here. Provide a clear and comprehensive description of the issue and your question. The more detail you provide for your issue and question, the easier it will be for other Lastolite Cubelite LiteTable owners to properly answer your question.

View the manual for the Lastolite Cubelite LiteTable here, for free. This manual comes under the category Other camera accessories and has been rated by 1 people with an average of a 7.5. This manual is available in the following languages: English. Do you have a question about the Lastolite Cubelite LiteTable or do you need help? Ask your question here

Lastolite Cubelite LiteTable specifications

General
Brand Lastolite
Model Cubelite LiteTable
Product Other camera accessory
EAN 5055135904780, 719821273356
Language English
Filetype PDF
Weight & dimensions
Dimensions (WxDxH) 1000 x 1000 x 1800 mm
Length 1000 mm
Width 1000 mm
Height 1800 mm
Features
Product colour Black,White
show more

Frequently Asked Questions

Below, you will find the most frequently asked questions about the Lastolite Cubelite LiteTable.

Is your question not listed? Ask your question here