Kubota SCL1000 manual

Kubota SCL1000
8.2 · 4
PDF manual
 · 82 pages
English
manualKubota SCL1000
Section 5: Maintenance & Lubrication
SCL1000 Stand-on Compact Loader 725-137MK 6/30/21
52

Table of Contents

Check Hydraulic Oil Level
!

WARNING

To avoid serious injury or death:
The following procedure should be performed with the
machine on a flat, level surface, the loader arms completely
lowered and the machine turned off. Use all the appropriate
personal protective equipment when performing maintenance.
Refer to Figure 5-11:
1. Open the machine’s hood. See “Opening & Closing
the Hood” on page 48.
2. Check oil level sight (#1) when oil temperatures are
between 50
o
F and 86
o
F (10
o
C and 30
o
C). The loader
arms must be down all the way and the curl cylinder
fully retracted to determine an accurate hydraulic oil
level reading. The oil level should be at or near the
middle of oil level sight (#1).
3. If oil level is too low, remove hydraulic cap lock (#5)
by removing 3/8-16 X 3/4 GR5 flanged bolt (#6).
Remove dust and dirt from hydraulic oil tank (#4) and
hydraulic oil tank cap (#3).
4. Remove hydraulic oil tank cap (#3) and add hydraulic
oil up to the middle of oil level sight (#1). It is
important for the protection of the hydraulic system to
only use the recommended hydraulic oil.
See “Recommended Fluids” on page 69.
5. Twist oil cap (#3) back on until it clicks once, then
replace hydraulic cap lock (#5) with 3/8-16 X 3/4 GR5
flanged bolt (#6).
6. Allow machine to idle for 1 minute before operating
any hydraulics to allow the hydraulic oil to be filtered
before reaching any contamination-sensitive areas.
Hydraulic Oil Level Check
Figure 5-11
IMPORTANT: Always use the correct hydraulic oil.
Using the wrong hydraulic oil can result in damage
to the hydraulic system.
5
3
6
73743
2
1
4
Check Engine Oil Level
!

WARNING

To avoid serious injury or death:
The following procedure should be performed with the
machine on a flat, level surface, the loader arms completely
lowered and the machine turned off. Use all the appropriate
personal protective equipment when performing maintenance.
Refer to Figure 5-12 & Figure 5-13
1. Open the machine’s hood. See “Opening & Closing
the Hood” on page 48.
2. Wipe off dirt and dust from around dipstick (#1).
3. Pull out dipstick (#1), wipe it clean with a clean rag
then put it back in and push it all the way in. Pull
dipstick (#1) out again and check to see if the oil level
lies between holes (A & B). See Figure 5-13.
4. If oil level is below hole (B), add new oil by removing
oil cap (#2) and pouring oil into the oil filling port with
a clean oil funnel. See “Recommended Fluids” on
page 69 for the correct engine oil.
5. Repeat steps 3 & 4 until the oil level is between holes
(A & B).
6. Replace oil cap (#2) and dipstick (#1) when finished.
Oil Cap
Figure 5-12
Dipstick
Figure 5-13
NOTE: For better accuracy, allow for the machine to
cool down sufficiently if it has been in operation.
IMPORTANT: Keep oil level between holes (A & B).
To avoid damage to the machine, do not over fill or
operate with low oil. Use the correct engine oil with
the correct viscosity for outside temperatures. See
“Recommended Fluids” on page 69.
1
2
72962
B
A
Dipstick
72964

View the manual for the Kubota SCL1000 here, for free. This manual comes under the category lawnmowers and has been rated by 4 people with an average of a 8.2. This manual is available in the following languages: English. Do you have a question about the Kubota SCL1000 or do you need help? Ask your question here

Need help?

Do you have a question about the Kubota and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 1
I
IsraelOctober 20, 2023

How do i input number code when i turn on machine it has acode i just cant seem to find numbers or how to get them in

How do i input number code when i turn on machine it has acode i just cant seem to find numbers or how to get them in
zoom-in
View photo

The Kubota SCL1000 is a lawnmower designed for efficient mowing of large areas. It features a powerful engine that provides reliable performance and ensures smooth operation. The lawnmower is equipped with a wide cutting deck, allowing for quick and efficient mowing, reducing the time required to complete the task. The SCL1000 is built with premium materials, ensuring durability and longevity. Its sturdy construction enables it to withstand tough conditions and heavy usage without compromising its performance. The lawnmower is designed for comfort, with adjustable seating positions and ergonomic controls, allowing the operator to maintain a comfortable position during operation. The Kubota SCL1000 is equipped with advanced technological features that contribute to its efficiency. It incorporates a cutting-edge cutting system that ensures a consistent and clean cut, leaving a well-manicured lawn behind. The lawnmower also includes safety features such as automatic shut-off and blade engagement, ensuring the operator's safety during operation. In summary, the Kubota SCL1000 is a high-quality lawnmower that offers powerful performance, durability, and efficiency. Its advanced features and sturdy construction make it an excellent choice for mowing large areas, providing a reliable and comfortable experience for the operator.

General
BrandKubota
ModelSCL1000
Productlawnmower
LanguageEnglish
FiletypeUser manual (PDF)

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Kubota SCL1000 below.

How short should I cut the grass?

When the grass is longer than 4.5cm, the grass should be cut. The ideal length is between 3 and 4.5cm.

How often should I cut the grass?

In the spring, the grass should be cut every week, while in the summer once every two weeks is sufficient.

Can I mow the lawn when the grass is wet?

You can, but the result is better in dry weather. When the grass is wet, grass clumps can easily form and clog the mower.

Why won't my Kubota SCL1000 lawnmower start?

Check if the fuel tank is filled with gasoline, the ignition switch is turned on, and the engine control lever is set to the correct position.

How do I adjust the cutting height on my Kubota SCL1000 lawnmower?

Locate the cutting height adjustment lever on the deck of the lawnmower and move it to the desired cutting height position.

What should I do if my Kubota SCL1000 lawnmower is not cutting the grass evenly?

Ensure that the mower blades are sharp and properly installed. If the issue persists, consider adjusting the deck level or inspecting the grass discharge chute for any blockages.

What could be causing excessive vibration in my Kubota SCL1000 lawnmower?

Check if the cutting blades are balanced and securely fastened. If they are damaged or bent, they may need to be replaced.

How do I clean the air filter on my Kubota SCL1000 lawnmower?

Locate the air filter housing, remove the cover, and take out the air filter. Clean the filter using compressed air or gently wash it with mild soap and warm water. Allow it to dry completely before reinstalling.

Is the manual of the Kubota SCL1000 available in English?

Yes, the manual of the Kubota SCL1000 is available in English .

Is your question not listed? Ask your question here

No results