Kubota MX5400 manual

Kubota MX5400
7 · 1
PDF manual
 · 172 pages
English
manualKubota MX5400
Port Coupler size
A, B, C, D, E, F PT 1/2
IMPORTANT :
Do not hold the remote-control-valve-lever in
the “REARWARD” position or the “FORWARD”
position once the remote cylinder has reached
the end of the stroke, because it will cause oil to
flow through the relief valve. Forcing oil
through the relief valve for extended periods
will overheat the oil.
When using the tractor-hydraulic-system to
power the front loader, do not operate the boom
and bucket cylinders simultaneously
NOTE :
To use the single-acting cylinder with the float
valve, connect the single-acting cylinder to the
port-C.
To extend a single-acting cylinder, pull the
remote-control-valve-lever rearward. To retract
a single-acting cylinder, push the remote-
control-valve-lever fully forward to the “FLOAT”
position. Do not hold the remote-control-valve-
lever in the down position, the transmission
fluid may be overheated.

3. How to use the remote control

valve coupler (if equipped)

WARNING

To avoid personal injury or death:
Stop the engine and relieve the pressure before
connecting or disconnecting the lines of
remote-control-valve-coupler.
Do not use your hands to check for leaks.
(1) Remote control valve cou-
pler (if equipped)
Connecting
1. Clean both implement coupler and tractor-
hydraulic-coupler.
2. Remove the dust plugs.
3. Insert the implement coupler to the tractor-
hydraulic-coupler.
4. Pull the implement coupler slightly to make sure
that the implement coupler and the tractor-
hydraulic-coupler are firmly connected.
NOTE :
Your local KUBOTA Dealer can supply parts to
adapt the implement coupler and the tractor-
hydraulic-coupler to hydraulic hoses.
Disconnecting
1. Lower the implement first to the ground to release
the hydraulic pressure in the hoses.
2. Clean the implement coupler and tractor-hydraulic-
coupler.
3. Relieve the pressure by moving the hydraulic-
control-levers with engine shut off.
4. Pull the hose straight from the tractor-hydraulic-
coupler to release it.
5. Clean the oil and dust from the tractor-hydraulic-
coupler, then replace the dust plugs.
REMOTE HYDRAULIC CONTROL SYSTEM (IF EQUIPPED)  HYDRAULIC UNIT
MX5400,MX6000
95

View the manual for the Kubota MX5400 here, for free. This manual comes under the category tractors and has been rated by 1 people with an average of a 7. This manual is available in the following languages: English. Do you have a question about the Kubota MX5400 or do you need help? Ask your question here

Need help?

Do you have a question about the Kubota and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 7
B
Brenda Ellison May 4, 2023

Tractor just quit. Below see lights that came on. What’s the problem and what does the lights mean?

Tractor just quit. Below see lights that came on. What’s the problem and what does the lights mean?
zoom-in
View photo
1 comment
E
Emma of manua.lsDecember 19, 2023

The problem and the meaning of the lights in case the Kubota MX5400 tractor suddenly stops are as follows: 1. Headlight Switch: Turn the headlight switch clockwise to activate the following lights: - (A) Off: Headlights are turned off. - (B) On (low): Headlights are dimmed as low beam. - (C) On (high): Headlights are turned on as high beam. 2. Hazard Light Switch and Turn Signal Light Switch: - (1) Headlight - (2) Turn signal / hazard light - (3) Rear turn signal / hazard light - (4) Tail light

This answer is automatically generated
S
steveApril 10, 2023

my regenration light and parked regenration light and engine rpm increase indicator is flashing what should i do to turn those off

S
StephJune 22, 2023

How can I check the parking break switch. My tractor will start cold but if I have to get off the tractor for any reason & it dies, it won’t start back. After it sits for awhile it would start back but now it won’t start at all. It has a new seat safety switch that was installed 2 days ago so that’s not my issue.

D
Dwain paulk March 4, 2024

Manual kill Kubota 5400 when u pull the kill know are you cutting off the fuel or the air

R
Richard willhite August 14, 2023

How to open hood

F
FrankJanuary 2, 2024

How do I adjust the clutch

Z
Zoe BoekbinderMay 9, 2023

Pto light flashing when pto is off

The Kubota MX5400 is a tractor that belongs to the MX series offered by Kubota, a Japanese machinery manufacturer. This tractor has a four-cylinder diesel engine with a rated output of 54 horsepower. It is equipped with an HST (hydrostatic transmission) that provides smooth and responsive operation. The tractor's rear three-point hitch has a lifting capacity of 2425 pounds, which enables it to handle a wide range of equipment. The Kubota MX5400 also has a hydraulic gear pump that delivers a maximum flow rate of 12.9 gallons per minute, allowing it to power hydraulic motors and cylinders quickly and efficiently. The tractor comes with a spacious operator's station that is designed for comfort and visibility. It has a deluxe suspension seat with armrests and adjustable lumbar support to help reduce operator fatigue during long work hours. The tractor's hood design provides excellent visibility of the surrounding area, while the instrument panel displays all the necessary information about the tractor's operation. The Kubota MX5400 is a versatile and reliable tractor that is suitable for a wide range of applications. It can be used for farming, landscaping, construction, and property maintenance tasks. It is equipped with features that enhance productivity and efficiency while providing operator comfort and convenience. Overall, the Kubota MX5400 is a quality tractor that lives up to the brand's reputation for excellence.

General
BrandKubota
ModelMX5400
Producttractor
LanguageEnglish
FiletypeUser manual (PDF)

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Kubota MX5400 below.

Why is my Kubota MX5400 tractor not starting?

Check the battery connections to ensure they are tight and free of corrosion. Inspect the fuel level and make sure you are using the proper fuel. Additionally, verify that the safety switches are engaged, such as ensuring the seat switch is activated.

How can I adjust the cutting height of the mower deck on my Kubota MX5400?

Locate the cutting height adjustment lever on the mower deck and move it to the desired position. Lower settings result in a shorter cut, while higher settings allow for a longer cut. Remember to adjust the lever evenly on both sides to maintain a level cut.

What should I do if my Kubota MX5400 tractor is overheating?

Ensure that the radiator and cooling fan are free from debris or obstructions. Check the coolant level and ensure it is within the recommended range. If necessary, you may need to clean or replace the radiator or have the cooling system inspected by a professional.

How do I engage the four-wheel drive (4WD) on my Kubota MX5400?

Locate the 4WD selector lever, usually located near the gear shift or on the control panel. Push or pull the lever, depending on the specific model, to engage or disengage the 4WD. Refer to the tractor's indicator lights or display to confirm that the 4WD is activated.

What could be causing my Kubota MX5400 tractor to have weak hydraulic power?

Check the hydraulic fluid level and ensure it is within the recommended range. Inspect the hydraulic filters for clogging or damage, as they may need replacement. Verify that the hydraulic system is not being overloaded or operating under excessive temperature conditions.

Is the manual of the Kubota MX5400 available in English?

Yes, the manual of the Kubota MX5400 is available in English .

Is your question not listed? Ask your question here

No results