View the manual for the Krups Calvi XP3458 here, for free. This manual comes under the category coffee makers and has been rated by 1 people with an average of a 5.2. This manual is available in the following languages: English. Do you have a question about the Krups Calvi XP3458 or do you need help? Ask your question here
| Brand | Krups |
| Model | Calvi XP3458 |
| Product | coffee maker |
| Language | English |
| Filetype | User manual (PDF) |
Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Krups Calvi XP3458 below.
How often a coffee machine needs to be descaled depends on how often it is used and the hardness of the water. If hard water is used it is recommended to descale once a month, if soft water is used once a quarter is sufficient.
To descale the coffee maker, it is recommended to use a liquid descaling agent which is labelled as suitable for coffee machines.
Espresso is a small amount of concentrated coffee.
The best-before date can be found on the packaging of the coffee beans. This best-before date applies as long as the bag is closed.
It is recommended to store coffee in an airtight and clean container.
How the coffee beans are ground strongly influences the taste of the coffee. If the coffee beans are very finely ground you will have a stronger taste and if the grind is coarser you will have a milder taste.
To select the coffee or steam function on the control panel of the Krups Calvi XP3458 coffee maker, follow these steps: 1. Locate the control panel on the machine. It is labeled as "D" in the diagram provided in the manual. 2. Identify the selector knob on the control panel. It is labeled as "D1" in the diagram. 3. Turn the selector knob to the desired function. For selecting the coffee function, position the knob accordingly. For selecting the steam function, adjust the knob to the appropriate setting. 4. Once you have set the selector knob to the desired function, the machine will be ready to perform the selected operation. Please note that the specific positions and labels on the control panel may vary slightly, but the general steps for selecting the coffee or steam function should be similar.
The selector knob on the Krups Calvi XP3458 coffee maker may not be working properly due to several reasons. Here are some possible causes and solutions: 1. Lack of water: If the water tank is empty or not filled properly, the pump may be deactivated. Fill the tank with water and re-initiate the pump according to the instructions in the manual. 2. Incorrect installation of the removable water tank: Ensure that the water tank is correctly positioned and fitted. Improper installation can affect the functioning of the selector knob. 3. Super cappuccino nozzle not properly installed: Check if the super cappuccino nozzle accessory is properly mounted on the appliance. Remove it and then install it again on the swivel arm by twisting it firmly from right to left. 4. Obstructed or twisted flexible hose: Make sure that the flexible hose connected to the super cappuccino nozzle is not obstructed or twisted. Ensure that it fits properly into the accessory to prevent any air intake. If none of these solutions resolve the issue with the selector knob, it is recommended to contact an approved service center for further assistance. Avoid disassembling the appliance yourself, as it may void the warranty.
To preheat the espresso before preparing it with the Krups Calvi XP3458 coffee maker, follow these steps: 1. Plug in the coffee maker and ensure that the water tank is filled with water at room temperature. 2. Turn on the appliance by pressing the on/off button. You will hear a short beep, indicating that the pump is activated. 3. The temperature light will flash while the machine heats up and then remain on, indicating that it is ready to use. 4. Unlock the filter holder by turning it to the left. 5. Add the appropriate filter for 1 cup or 2 cups to the filter holder. 6. Use the measuring spoon provided to add the desired amount of ground coffee to the filter. One scoop is recommended for 1 cup, and two scoops for 2 cups. 7. Remove any excess coffee from the rim of the filter holder. 8. Insert the filter holder into the appliance, pushing it firmly to the right until it stops. 9. Place one or two cups on the drip tray grid under the filter holder. 10. Turn the selector knob to the espresso position. 11. After a few moments, the coffee will start to flow through the filter into the cups. 12. When the desired amount of coffee has been dispensed, return the selector knob to the O position. 13. Remove the cups and enjoy your preheated espresso. Please note that these instructions are based on the available information and may vary slightly depending on the specific model of the Krups Calvi XP3458 coffee maker.
If the espresso is not preheating properly on your Krups Calvi XP3458 coffee maker, there could be a few possible reasons for this issue. Here are some steps to troubleshoot the problem: 1. Check the water tank: Ensure that the water tank is filled with enough water at room temperature. If the water level is too low, the machine may not be able to heat the espresso properly. 2. Verify the power supply: Make sure that the coffee maker is properly plugged into a functioning power outlet. Check if the power cord is securely connected to the machine. 3. Allow sufficient warm-up time: The espresso machine needs some time to heat up before it can preheat the espresso. Wait for the temperature light to stop flashing and remain on, indicating that the machine is ready for use. 4. Clean the machine: If there is a buildup of coffee residue or mineral deposits, it can affect the heating performance. Follow the cleaning instructions in the manual to descale and clean the machine regularly. 5. Contact customer support: If the issue persists after following these steps, it is recommended to contact Krups customer support for further assistance. They can provide specific troubleshooting advice or arrange for repairs if necessary. Remember to always refer to the manual for detailed instructions and safety precautions specific to your Krups Calvi XP3458 coffee maker.
To preheat the steam before using it with the Krups Calvi XP3458 coffee maker, follow these steps: 1. Fill the water tank with water at room temperature and ensure it is properly placed on the appliance. 2. Switch on the coffee maker by pressing the on/off button. The temperature light will flash while the machine is preheating. 3. Wait for the temperature light to stop flashing and remain on. This indicates that the machine is ready to use. 4. Connect the super cappuccino nozzle to the swivel arm by tightly fastening it with a twist from right to left. 5. Select the desired position on the special nozzle for either cappuccino or caffe latte. 6. Place a cup under the super cappuccino nozzle and pour fresh and cold semi-skimmed milk (60 to 100 ml) into a container. 7. Plunge the bevelled end of the silicone tube into the container, ensuring it is not twisted. 8. Turn the selector knob to the preheat position. The on/off indicator will blink and then stay lit, indicating that the appliance is ready for use. 9. Turn the selector knob to the steam position to start producing steam. 10. Once you have produced enough frothed milk, turn the selector knob to position 0 to stop the cycle. 11. After the automatic cooling operation is completed, you can start preparing your coffee by placing your cup of frothed milk under the filter holder. Please note that these instructions are based on the available information and may vary slightly depending on the specific model of the Krups Calvi XP3458 coffee maker.
If the steam is not preheating properly on your Krups Calvi XP3458 coffee maker, there could be a few possible reasons for this issue. Here are some steps to troubleshoot the problem: 1. Check the water tank: Ensure that the water tank is filled with enough water at room temperature. If the water level is too low, the machine may not be able to generate enough steam. 2. Verify the power supply: Make sure that the coffee maker is properly plugged into a functioning power outlet. Check if the power cord is securely connected to the machine. 3. Allow sufficient warm-up time: The espresso machine needs some time to heat up before it can generate steam. Wait for the temperature light to stop flashing and remain on, indicating that the machine is ready for use. 4. Clean the steam nozzle: If there is a buildup of milk residue or mineral deposits on the steam nozzle, it can affect the steam generation. Clean the steam nozzle according to the instructions in the manual to ensure proper functioning. 5. Contact customer support: If the issue persists after following these steps, it is recommended to contact Krups customer support for further assistance. They can provide specific troubleshooting advice or arrange for repairs if necessary. Remember to always refer to the manual for detailed instructions and safety precautions specific to your Krups Calvi XP3458 coffee maker.
To prepare an espresso using the Krups Calvi XP3458 coffee maker, follow these steps: 1. Fill the water tank with fresh water at room temperature and ensure it is properly placed on the appliance. 2. Switch on the coffee maker by pressing the on/off button. The temperature light will flash while the machine is preheating. 3. Wait for the temperature light to stop flashing and remain on. This indicates that the machine is ready to use. 4. Unlock the filter holder by turning it to the left. 5. Add the appropriate filter for 1 cup or 2 cups to the filter holder. 6. Use the measuring spoon provided to add the desired amount of ground coffee to the filter. One scoop is recommended for 1 cup, and two scoops for 2 cups. 7. Remove any excess coffee from the rim of the filter holder. 8. Insert the filter holder into the appliance, pushing it firmly to the right until it stops. 9. Place one or two cups on the drip tray grid under the filter holder. 10. Turn the selector knob to the espresso position. 11. After a few moments, the coffee will start to flow through the filter into the cups. 12. When the desired amount of coffee has been dispensed, return the selector knob to the O position. 13. Remove the cups and enjoy your freshly brewed espresso. Please note that these instructions are based on the available information and may vary slightly depending on the specific model of the Krups Calvi XP3458 coffee maker.
If the espresso is not brewing properly on your Krups Calvi XP3458 coffee maker, there could be a few possible reasons for this issue. Here are some steps to troubleshoot the problem: 1. Check the water tank: Ensure that the water tank is filled with enough water at room temperature. If the water level is too low, the machine may not be able to extract the espresso properly. 2. Verify the power supply: Make sure that the coffee maker is properly plugged into a functioning power outlet. Check if the power cord is securely connected to the machine. 3. Clean the filter holder: If there is a buildup of coffee residue or mineral deposits in the filter holder, it can affect the brewing process. Remove the filter holder and clean it thoroughly according to the instructions in the manual. 4. Adjust the grind size: If the coffee grounds are too fine or too coarse, it can impact the extraction process. Experiment with different grind sizes to find the optimal setting for your taste preferences. 5. Use the correct amount of coffee: Ensure that you are using the recommended amount of ground coffee for the desired number of cups. Too much or too little coffee can affect the brewing process. 6. Contact customer support: If the issue persists after following these steps, it is recommended to contact Krups customer support for further assistance. They can provide specific troubleshooting advice or arrange for repairs if necessary. Remember to always refer to the manual for detailed instructions and safety precautions specific to your Krups Calvi XP3458 coffee maker.
The water compartment lid on the Krups Calvi XP3458 coffee maker is located on the top of the machine. Here are the steps to locate it: 1. Look at the top of the coffee maker, where you will find a hinged lid. 2. Lift the lid to access the water compartment. 3. The water compartment is where you pour water into the machine for brewing coffee. 4. Ensure that the water compartment lid is securely closed after filling it with water. Please note that the specific design and location of the water compartment lid may vary slightly depending on the model of the Krups Calvi XP3458 coffee maker. However, in general, it is located on the top of the machine for easy access and convenient water filling.
To remove and refill the water tank on the Krups Calvi XP3458 coffee maker, follow these steps: 1. Locate the water tank on the back or side of the coffee maker. It is a removable container that holds the water for brewing. 2. Lift the water tank straight up to remove it from the coffee maker. Be careful not to spill any water. 3. Take the water tank to a sink or water source for refilling. 4. Open the lid or cap of the water tank to access the filling opening. 5. Fill the water tank with fresh water at room temperature. Ensure that you do not exceed the maximum fill line indicated on the tank. 6. Close the lid or cap of the water tank securely to prevent any leaks. 7. Carefully place the filled water tank back into the coffee maker, aligning it with the designated slot or area. 8. Push the water tank down firmly until it clicks into place. 9. Ensure that the water tank is properly seated and secure before starting the brewing process. Please note that these instructions are based on the available information and may vary slightly depending on the specific model of the Krups Calvi XP3458 coffee maker.
To use the filter holder on the Krups Calvi XP3458 coffee maker, follow these steps: 1. Unlock the filter holder by turning it to the left. This will release the filter holder from the machine. 2. Choose the appropriate filter for your desired number of cups. The filter holder is designed to accommodate filters for 1 cup or 2 cups. 3. Insert the selected filter into the filter holder. Ensure that it is securely placed and fits snugly. 4. Use the provided measuring spoon to add the desired amount of ground coffee to the filter. One scoop is recommended for 1 cup, and two scoops for 2 cups. 5. Remove any excess coffee from the rim of the filter holder to ensure a proper seal. 6. Insert the filter holder back into the machine, aligning it with the designated slot or area. 7. Push the filter holder firmly to the right until it locks into place. 8. The coffee maker is now ready to brew your coffee. Follow the instructions for selecting the desired brewing function and starting the brewing process. Please note that these instructions are based on the available information and may vary slightly depending on the specific model of the Krups Calvi XP3458 coffee maker.
If the filter holder is not fitting properly on your Krups Calvi XP3458 coffee maker, there could be a few possible reasons for this issue. Here are some steps to troubleshoot the problem: 1. Check the alignment: Ensure that the filter holder is properly aligned with the designated slot or area on the machine. Make sure it is inserted straight and pushed all the way to the right until it locks into place. 2. Clean the filter holder and machine: If there is any coffee residue or debris on the filter holder or inside the machine, it can affect the fit. Clean the filter holder and the area where it is inserted using a damp cloth or sponge. 3. Verify the filter size: Ensure that you are using the correct size filter for your desired number of cups. Using the wrong size filter can prevent the holder from fitting properly. Refer to the manual or product specifications to determine the appropriate filter size. 4. Contact customer support: If the issue persists after following these steps, it is recommended to contact Krups customer support for further assistance. They can provide specific troubleshooting advice or arrange for repairs if necessary. Remember to always refer to the manual for detailed instructions and safety precautions specific to your Krups Calvi XP3458 coffee maker.
To use the super cappuccino nozzle on the Krups Calvi XP3458 coffee maker, follow these steps: 1. Connect the super cappuccino nozzle to the swivel arm by tightly fastening it with a twist from right to left. 2. Select either the cappuccino or caffe latte position on the special nozzle. This can be done by adjusting the position of the nozzle according to the desired drink. 3. Place a cup under the super cappuccino nozzle and pour fresh and cold semi-skimmed milk (60 to 100 ml) into a container. 4. Plunge the bevelled end of the silicone tube into the container, ensuring it is not twisted. 5. Turn the selector knob to the preheat position. The on/off indicator will blink and then stay lit, indicating that the appliance is ready for use. 6. Turn the selector knob to the steam position to start producing steam. 7. Once you have produced enough frothed milk, turn the selector knob to position 0 to stop the cycle. 8. After the automatic cooling operation is completed, you can start preparing your coffee by placing your cup of frothed milk under the filter holder. Please note that these instructions are based on the available information and may vary slightly depending on the specific model of the Krups Calvi XP3458 coffee maker.
If the super cappuccino nozzle is not producing frothy milk on your Krups Calvi XP3458 coffee maker, there could be a few possible reasons for this issue. Here are some steps to troubleshoot the problem: 1. Check the installation: Ensure that the super cappuccino nozzle is properly installed on the swivel arm. Remove it and then install it again, making sure to twist it firmly from right to left. 2. Verify the flexible hose: Check that the flexible hose connected to the super cappuccino nozzle is not obstructed or twisted. Ensure that it fits properly into the accessory to prevent any air intake. 3. Clean the accessory: Rinse and clean the super cappuccino nozzle and the silicone tube according to the maintenance and cleaning instructions in the manual. This will help remove any milk residue or blockages that may be affecting the frothing process. 4. Use fresh and cold milk: Ensure that you are using fresh and cold semi-skimmed milk. Using very fresh and cold milk can help improve the frothing results. 5. Preheat the appliance: Before using the super cappuccino nozzle, make sure to preheat the appliance by turning the selector knob to the preheat position. This will ensure that the machine is ready to produce steam for frothing. If the issue persists after following these steps, it is recommended to contact Krups customer support for further assistance. They can provide specific troubleshooting advice or arrange for repairs if necessary.
If the coffee is not tasting good on your Krups Calvi XP3458 coffee maker, there could be a few possible reasons for this issue. Here are some steps to troubleshoot the problem: 1. Check the coffee freshness: Ensure that you are using freshly roasted coffee beans. Stale coffee can result in a less flavorful and less enjoyable cup. 2. Adjust the grind size: If the coffee is tasting bitter or weak, the grind size may need to be adjusted. Experiment with different grind settings to find the optimal size for your taste preferences. 3. Use the correct coffee-to-water ratio: Ensure that you are using the recommended amount of coffee for the desired number of cups. Using too much or too little coffee can affect the taste. 4. Check the water quality: The quality of water used can impact the taste of the coffee. Use filtered or bottled water if your tap water has a strong taste or odor. 5. Clean the machine: Regularly clean the coffee maker, including the filter holder and brewing components, to remove any coffee residue or buildup that can affect the taste. 6. Consider the coffee beans: Different coffee beans have varying flavor profiles. Experiment with different origins and blends to find the beans that suit your taste preferences. If the issue persists after following these steps, it is recommended to contact Krups customer support for further assistance. They can provide specific troubleshooting advice or arrange for repairs if necessary.
If the coffee is not hot enough on your Krups Calvi XP3458 coffee maker, there could be a few possible reasons for this issue. Here are some steps to troubleshoot the problem: 1. Check the water temperature: Ensure that you are using cold water at room temperature to fill the water tank. Using hot water can affect the brewing temperature. 2. Preheat the machine: Before brewing, make sure to preheat the coffee maker by turning it on and allowing it to warm up for a few minutes. This helps to ensure that the brewing temperature is optimal. 3. Adjust the brewing temperature: Some coffee makers allow you to adjust the brewing temperature. Check if your Krups Calvi XP3458 coffee maker has this feature and adjust it to a higher temperature if necessary. 4. Clean the machine: Coffee residue or mineral deposits can affect the heating performance. Regularly clean the coffee maker, including the heating element, to remove any buildup. 5. Use preheated cups: Preheat your cups by rinsing them with hot water before brewing. This helps to maintain the temperature of the coffee. If the issue persists after following these steps, it is recommended to contact Krups customer support for further assistance. They can provide specific troubleshooting advice or arrange for repairs if necessary.
To grind the coffee just before preparation on the Krups Calvi XP3458 coffee maker, follow these steps: 1. Choose whole coffee beans: Select high-quality whole coffee beans for the best flavor and freshness. 2. Set up the grinder: If your Krups Calvi XP3458 coffee maker has a built-in grinder, ensure that it is properly set up and adjusted according to your desired grind size. 3. Measure the coffee beans: Use a kitchen scale or the provided measuring spoon to measure the desired amount of coffee beans. The recommended ratio is typically 1 to 2 tablespoons of coffee beans per cup of water. 4. Grind the coffee beans: Place the measured coffee beans into the grinder and start the grinding process. Follow the instructions for your specific grinder to achieve the desired grind size. 5. Collect the ground coffee: Once the grinding process is complete, collect the freshly ground coffee in a container or directly into the filter holder of your Krups Calvi XP3458 coffee maker. 6. Brew the coffee: Proceed with the brewing process according to the instructions for your specific coffee maker, using the freshly ground coffee for the best flavor and aroma. Please note that these instructions are based on general guidelines and may vary depending on the specific model of the Krups Calvi XP3458 coffee maker.
If the coffee is not grinding properly on your Krups Calvi XP3458 coffee maker, there could be a few possible reasons for this issue. Here are some steps to troubleshoot the problem: 1. Check the coffee beans: Ensure that you are using whole coffee beans and not pre-ground coffee. Pre-ground coffee can clog the grinder and affect the grinding process. 2. Adjust the grind size: If the coffee is not grinding to the desired consistency, adjust the grind size setting on your coffee grinder. Experiment with different settings to find the optimal grind size for your taste preferences. 3. Clean the grinder: Coffee residue or oil buildup can affect the performance of the grinder. Regularly clean the grinder according to the cleaning instructions in the manual to remove any residue or blockages. 4. Check for blockages: Inspect the grinder for any blockages or obstructions that may be preventing the coffee beans from grinding properly. Clear any blockages carefully using a brush or other suitable tool. 5. Contact customer support: If the issue persists after following these steps, it is recommended to contact Krups customer support for further assistance. They can provide specific troubleshooting advice or arrange for repairs if necessary. Remember to always refer to the manual for detailed instructions and safety precautions specific to your Krups Calvi XP3458 coffee maker.
To adjust the coffee strength using the control panel of the Krups Calvi XP3458 coffee maker, follow these steps: 1. Fill the water tank with water at room temperature and place it back on the appliance. 2. Switch on the appliance by pressing the on/off button. The light will flash while it is preheating and then remain on when it is ready to use. 3. Unlock the filter holder by turning it to the left and place a filter in the one cup filter. 4. Insert the filter holder into the appliance, pushing it firmly to the right as far as it will go. 5. To adjust the coffee strength, turn the selector knob on the control panel to the desired position. The options may include different coffee strength settings, such as mild, medium, or strong. 6. Once you have selected the desired coffee strength, press the on/off button again to start the brewing process. 7. The coffee maker will now brew the coffee according to the selected strength setting. 8. Once the brewing process is complete, remove the filter holder and enjoy your coffee. By following these steps, you can easily adjust the coffee strength using the control panel of the Krups Calvi XP3458 coffee maker.
The water compartment lid may not be closing properly on your Krups Calvi XP3458 coffee maker due to the following possible causes and solutions: 1. The water tank is not fitted correctly: Check that the tank is properly inserted into the appliance. Ensure it is securely in place to create a proper seal. 2. The water compartment lid is misaligned: Make sure the lid is aligned properly with the water compartment. Adjust the position of the lid to ensure it fits snugly. 3. The water compartment lid is damaged or worn: Inspect the lid for any signs of damage or wear. If the lid is cracked or broken, it may need to be replaced. Contact an approved service center for assistance. 4. There is an obstruction or debris preventing the lid from closing: Clean the area around the water compartment and lid to remove any debris or obstructions. Ensure there are no coffee grounds or other substances blocking the lid's closure. By checking and addressing these possible causes, you should be able to resolve the issue of the water compartment lid not closing properly on your Krups Calvi XP3458 coffee maker.
To remove and clean the filter holder of the Krups Calvi XP3458 coffee maker, follow these steps: 1. Ensure that the coffee maker is unplugged and cooled down before cleaning. 2. Wash the filter holder and filter under running water to remove any remaining coffee grounds. 3. Use a damp cloth to clean the filter holder mount regularly and remove any coffee residues stuck to the surface. 4. To prolong the useful life of the watertight seal on the brewing head, do not put the filter holder back in place if the coffee machine has not been used for extended periods. 5. If there are any deposits that could block the flow of your 1 or 2 cup filter, you may use a needle to remove them. 6. After cleaning, ensure that the filter holder and filter are completely dry before reassembling them back into the coffee maker. By following these steps, you can easily remove and clean the filter holder of the Krups Calvi XP3458 coffee maker, ensuring optimal performance and taste for your coffee.
The steam function may not be working on your Krups Calvi XP3458 coffee maker due to the following possible causes and solutions: 1. Lack of water in the tank: Ensure that the water tank is filled with an adequate amount of water. If the tank is empty or low on water, the steam function will not work. Refill the tank as needed. 2. Deactivated pump: If the pump has been deactivated due to a lack of water, fill the tank with water and re-initiate the pump. Avoid completely emptying the tank to prevent deactivation. 3. Improper installation of the super cappuccino nozzle: Check that the accessory has been properly mounted on the appliance. Remove it and then install it again on the swivel arm by twisting it firmly from right to left. 4. Obstruction or twisting of the flexible hose: Ensure that the flexible hose is not obstructed or twisted and that it fits properly into the accessory. This will prevent any air intake and ensure proper steam flow. 5. Malfunction or blockage: If none of the above solutions resolve the issue, it is recommended to contact an approved service center for further assistance. Do not attempt to disassemble the appliance yourself, as it may void the warranty. By checking and addressing these possible causes, you should be able to troubleshoot and resolve the issue of the steam function not working on your Krups Calvi XP3458 coffee maker.
The recommended coffee grind size for the Krups Calvi XP3458 coffee maker is not explicitly mentioned in the available manual. However, the manual provides some practical tips for coffee preparation. It suggests using freshly roasted coffee and grinding the coffee just before brewing for the best results. It also recommends choosing pure Arabica coffee or those made from a majority of Arabica coffee for a coffee rich in aroma. Based on these recommendations, it is advisable to use a medium to fine grind size for the Krups Calvi XP3458 coffee maker. This grind size allows for proper extraction of flavors without clogging the filter or resulting in a weak brew. Experimenting with different grind sizes and adjusting according to personal preference is also encouraged. Remember to always use a burr grinder for a consistent grind size and avoid using a blade grinder, as it may result in uneven particle sizes.
Yes, the manual of the Krups Calvi XP3458 is available in English .
Is your question not listed? Ask your question here
No results
Need help?
Do you have a question about the Krups and is the answer not in the manual?
Question and answer
Number of questions: 0