Korg SoundLink DRS 1212 I/O manual

Korg SoundLink DRS 1212 I/O
7.5 · 1
PDF manual
 · 58 pages
English
manualKorg SoundLink DRS 1212 I/O
System Configurations
Korg 1212 I/O 19
English

Setting the word clock source on an ADAT system

ADATs have three settings for word clock source: “Digital,” “Internal,” and
“External.”
Digital means that they sync to an external clock through their optical or 9-
pin inputs, if they are connected to another ADAT optical device (such as
the 1212 I/O); if there are no other devices connected, then they use their
internal clock.
Internal means that they use their internal clock, regardless of any signal at
the optical input.
External will only appear if the ADAT is connected to a BRC, or another
ADAT sync master (such as the Mark Of The Unicorn MIDI Timepiece AV).
In a multi-device system without the Alesis BRC, the first device (the unit
that displays “Id 1” at startup) will have been designated the word clock
master at startup, and this is the only one you need to change. The rest of
the devices will automatically be set to slave to the master through their
digital inputs.
When using the Alesis BRC, you do not need to make any settings on the
ADATs themselves (they’ll automatically be set to External); instead, the
BRC controls the word clock of the connected ADATs. See below for
instructions on working with the BRC.
ADAT XT, Fostex CX-8, Panasonic MDA-1 (without BRC)
On the ADAT XT, Fostex CX-8, and Panasonic MDA-1, both the word clock
source and the sample rate are set using the Clock Source button on the
front panel. The current Clock Source setting is shown in the lower right-
hand side of the fluorescent display. Pressing the button repeatedly toggles
through the four choices: INT 48kHz, INT 44.1kHz, DIG 48kHz, and DIG
44.1kHz. “INT” is Internal, and “DIG” is Digital.
If the ADAT is providing the master clock source, the sample rate (48kHz
or 44.1kHz) will control the entire system, including the 1212 I/O. If the
tape is not formatted for the current sample rate, the sample rate may flash
in the display, and the front-panel clock may not be correct, but otherwise
everything will be fine; please see your ADAT manual for details.
If DIG is selected, the on-screen “DIG” indicator will flash if there is a
problem with the signal at the ADAT’s optical input (such as no cable
connected, or invalid word clock).
Original ADAT (without BRC)
On the original ADAT, hold the “SET LOCATE” button, and then press
“DIGITAL IN.” This toggles the ADAT between “int” (Internal) and “dig”
(Digital). This is a little tricky, since you cannot see the setting without
changing it. Press the buttons until you see the desired setting.

Manual

View the manual for the Korg SoundLink DRS 1212 I/O here, for free. This manual comes under the category hi-fi systems and has been rated by 1 people with an average of a 7.5. This manual is available in the following languages: English. Do you have a question about the Korg SoundLink DRS 1212 I/O or do you need help? Ask your question here

Index

Need help?

Do you have a question about the Korg and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 1
D
Davide VecchiOctober 25, 2020

E' compatibile con macOS 10.14.6

Korg SoundLink DRS 1212 I/O specifications

Below you will find the product specifications and the manual specifications of the Korg SoundLink DRS 1212 I/O.

General
BrandKorg
ModelSoundLink DRS 1212 I/O
Producthi-fi system
LanguageEnglish
FiletypeUser manual (PDF)

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Korg SoundLink DRS 1212 I/O below.

When is my volume too loud?

A volume above 80 decibels can be harmful to hearing. When the volume exceeds 120 decibels, direct damage can even occur. The chance of hearing damage depends on the listening frequency and duration.

Can bluetooth devices of different brands be connected to each other?

Yes, bluetooth is a universal method that allows different devices equipped with bluetooth to connect to each other.

What is bluetooth?

Bluetooth is a way of exchanging data wirelessly between electronic devices via radio waves. The distance between the two devices that exchange data can in most cases be no more than ten metres.

What is HDMI?

HDMI stands for High-Definition Multimedia Interface. An HDMI cable is used to transport audio and video signals between devices.

How can I best clean my hi-fi system?

A slightly damp cleaning cloth or soft, dust-free cloth works best to remove fingerprints. Dust in hard-to-reach places is best removed with compressed air.

Wat is Dolby Atmos?

Dolby Atmos is a technology that ensures that the sound is reflected from the ceiling to where you are listening. This makes it possible to create a 5.1 effect with only 1 speaker.

Is the manual of the Korg SoundLink DRS 1212 I/O available in English?

Yes, the manual of the Korg SoundLink DRS 1212 I/O is available in English .

Is your question not listed? Ask your question here

No results