Korg SoundLink DRS 1212 I/O manual

Korg SoundLink DRS 1212 I/O
7.5 · 1
PDF manual
 · 58 pages
English
manualKorg SoundLink DRS 1212 I/O
Installation
Korg 1212 I/O 9
English
Stereo analog input
This input is used to bring analog signals into the 1212 I/O. You can
connect this to the output of a mixer, microphone pre-amp, synthesizer,
and so on. To allow use with a wide range of equipment, the analog input
may be configured for either +4 dBu or -10 dBV signal levels. For more
information, please see “Analog levels: +4 or -10” on page 3.
Microphones and electric guitar outputs should be sent through a mixer or
pre-amp first, to bring them up to +4 or -10 levels; otherwise, their signals
will be too weak.
The analog input uses a 1/4” TRS (tip-ring-sleeve) connector to carry a
stereo, unbalanced signal. The tip carries the right side, the ring carries the
left side, and the sleeve carries the ground. You can use standard “insert”
cables to bring the signals out to a pair of 1/4” mono connectors.
Stereo analog output
This connector is used to bring analog signals out of the 1212 I/O, into
your mixer, amplifier, etc. To allow use with a wide range of equipment, the
analog output may be configured for either +4 dBu or -10 dBV signal levels.
For more information, please see “Analog levels: +4 or -10” on page 3.
As with the analog inputs, described above, the output uses a 1/4” TRS
(tip-ring-sleeve) connector to carry a stereo, unbalanced signal. The tip
carries the right side, the ring carries the left side, and the sleeve carries the
ground. You can use standard “insert” cables to bring the signals out to a
pair of 1/4” mono connectors.
ADAT optical input
The ADAT optical input carries eight channels of digital audio. You can
connect this to the digital output of any multitrack recorder, digital mixer,
effects processor, or other digital audio device which supports the ADAT
optical format.
You can also connect this to the SoundLink DRS 880 A/D Audio Interface,
which will provide the 1212 I/O with eight additional analog inputs.
ADAT optical output
The ADAT optical output carries eight channels of digital audio. You can
connect this to the digital input of any multitrack recorder, digital mixer,
effects processor, or other digital audio device which supports the ADAT
optical format.
You can also connect this to the SoundLink DRS 880 D/A Audio Interface,
which will provide the 1212 I/O with eight additional analog outputs.
S/PDIF breakout connector
This connector should only be used with the special S/PDIF breakout cable
included with the 1212 I/O. This cable has a 4-pin mini-DIN connector at

Manual

View the manual for the Korg SoundLink DRS 1212 I/O here, for free. This manual comes under the category hi-fi systems and has been rated by 1 people with an average of a 7.5. This manual is available in the following languages: English. Do you have a question about the Korg SoundLink DRS 1212 I/O or do you need help? Ask your question here

Index

Need help?

Do you have a question about the Korg and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 1
D
Davide VecchiOctober 25, 2020

E' compatibile con macOS 10.14.6

Korg SoundLink DRS 1212 I/O specifications

Below you will find the product specifications and the manual specifications of the Korg SoundLink DRS 1212 I/O.

General
BrandKorg
ModelSoundLink DRS 1212 I/O
Producthi-fi system
LanguageEnglish
FiletypeUser manual (PDF)

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Korg SoundLink DRS 1212 I/O below.

When is my volume too loud?

A volume above 80 decibels can be harmful to hearing. When the volume exceeds 120 decibels, direct damage can even occur. The chance of hearing damage depends on the listening frequency and duration.

Can bluetooth devices of different brands be connected to each other?

Yes, bluetooth is a universal method that allows different devices equipped with bluetooth to connect to each other.

What is bluetooth?

Bluetooth is a way of exchanging data wirelessly between electronic devices via radio waves. The distance between the two devices that exchange data can in most cases be no more than ten metres.

What is HDMI?

HDMI stands for High-Definition Multimedia Interface. An HDMI cable is used to transport audio and video signals between devices.

How can I best clean my hi-fi system?

A slightly damp cleaning cloth or soft, dust-free cloth works best to remove fingerprints. Dust in hard-to-reach places is best removed with compressed air.

Wat is Dolby Atmos?

Dolby Atmos is a technology that ensures that the sound is reflected from the ceiling to where you are listening. This makes it possible to create a 5.1 effect with only 1 speaker.

Is the manual of the Korg SoundLink DRS 1212 I/O available in English?

Yes, the manual of the Korg SoundLink DRS 1212 I/O is available in English .

Is your question not listed? Ask your question here

No results