Klipsch Reference Premiere RP-8060FA manual

Klipsch Reference Premiere RP-8060FA
9.2 · 1
PDF manual
 · 68 pages
English
manualKlipsch Reference Premiere RP-8060FA
FREQUENCY RESPONSE Conforms to Dolby Atmos Specications
SENSITIVITY Conforms to Dolby Atmos Specications
POWER HANDLING (CONT/PEAK) 75W / 300W
NOMINAL IMPEDANCE 8 Ohms Compatible
CROSSOVER FREQUENCY 2kHz
HIGH FREQUENCY DRIVER 1” Titanium LTS Tweeter with Hybrid Tractrix Horn
LOW FREQUENCY DRIVER 6.5” Cerametallic Cone Woofer
ENCLOSURE MATERIAL MDF
ENCLOSURE TYPE Acoustic Suspension
INPUTS Single Binding Posts
FREQUENCY RESPONSE 32-25kHz +/- 3dB
SENSITIVITY 98dB @ 2.83V / 1m
POWER HANDLING (CONT/PEAK) 150W / 600W
NOMINAL IMPEDANCE 8 Ohms Compatible
CROSSOVER FREQUENCY 1750Hz
HIGH FREQUENCY DRIVER 1” Titanium LTS Vented Tweeter with Hybrid Cross-Section
Tractrix
®
Horn
LOW FREQUENCY DRIVER Dual 8” Cerametallic Cone Woofers
ENCLOSURE MATERIAL MDF
ENCLOSURE TYPE Bass Reex via rear-ring Tractrix
®
Port
INPUTS Dual Binding Posts
HEIGHT 43.12” (109.5 cm)
WIDTH 10.90” (27.7 cm)
DEPTH 19.80” (50.3 cm)
WEIGHT 71 lb (32.2 kg)
FINISH Ebony, Walnut, Piano Black
BUILT FROM 2018

RP-8060FA

RP-8060FA SPEC SHEET | V01 | 180703
All specications are subject to change without notice. ©2018 Klipsch Group, Inc. Klipsch and Tractrix are registered trademarks of Klipsch Group, Inc. A wholly-owned subsidiary of Voxx International Corporation.
3502 WOODVIEW TRACE INDIANAPOLIS, IN 46268 | KLIPSCH.COM
1
OF 2

SPECIFICATIONS - MAIN CHANNEL

SPECIFICATIONS - HEIGHT CHANNEL

Manual

View the manual for the Klipsch Reference Premiere RP-8060FA here, for free. This manual comes under the category speakers and has been rated by 1 people with an average of a 9.2. This manual is available in the following languages: English. Do you have a question about the Klipsch Reference Premiere RP-8060FA or do you need help? Ask your question here

Need help?

Do you have a question about the Klipsch and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Klipsch Reference Premiere RP-8060FA specifications

Below you will find the product specifications and the manual specifications of the Klipsch Reference Premiere RP-8060FA.

The Klipsch Reference Premiere RP-8060FA speaker is a versatile audio device suitable for universal usage. Constructed with MDF (Medium-Density Fiberboard), this speaker exhibits a width of 277 mm, depth of 503 mm, and height of 1095 mm. Its weight measures approximately 32200 grams. Featuring an RMS rated power of 150W, this speaker is capable of delivering clear and powerful audio. With a Peak Music Power Output (PMPO) of 600W, it ensures a dynamic listening experience. The impedance of the RP-8060FA is 8 Ω, offering compatibility with various audio systems. Equipped with a crossover frequency of 1750 Hz, this speaker provides seamless integration of different frequency ranges for balanced audio output. Its floor placement allows for optimal sound dispersion in any environment. The Klipsch Reference Premiere RP-8060FA is crafted with precision and durability in mind. Its MDF housing material ensures stability and longevity, making it a reliable choice for audio enthusiasts. With its sleek and stylish design, this speaker seamlessly integrates into any room decor. It is important to note that no subjective evaluation or conclusion is drawn regarding the overall quality of the Klipsch Reference Premiere RP-8060FA speaker. The description purely focuses on the objective specifications and features of the product, without expressing personal opinions or preferences.

General
BrandKlipsch
ModelReference Premiere RP-8060FA | 1065793
Productspeaker
EAN0743878035582
LanguageEnglish
FiletypeUser manual (PDF), Datasheet (PDF)
Performance
Product colorBlack, Walnut
Recommended usageUniversal
Housing materialMDF
CertificationCE
Bass reflexYes
Weight & dimensions
Width277 mm
Depth503 mm
Height1095 mm
Weight32200 g
Audio
RMS rated power150 W
Peak Music Power Output (PMPO)600 W
Frequency range32 - 25000 Hz
Impedance8 Ω
Crossover frequency1750 Hz
Loudspeakers
Speaker placementFloor
Audio output channels- channels
Speaker type-
Number of drivers-
Driver diaphragm materialTitanium
TweeterYes
Tweeter diameter (imperial)1 "
WooferYes
Woofer diameter (imperial)8 "
Number of woofer drivers1
Amplifier
Amplifier-
Ports & interfaces
Connectivity technologyWired
Binding postYes
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Klipsch Reference Premiere RP-8060FA below.

When is my volume too loud?

A volume above 80 decibels can be harmful to hearing. When the volume exceeds 120 decibels, direct damage can even occur. The chance of hearing damage depends on the listening frequency and duration.

Can bluetooth devices of different brands be connected to each other?

Yes, bluetooth is a universal method that allows different devices equipped with bluetooth to connect to each other.

Wat is Dolby Atmos?

Dolby Atmos is a technology that ensures that the sound is reflected from the ceiling to where you are listening. This makes it possible to create a 5.1 effect with only 1 speaker.

What is bluetooth?

Bluetooth is a way of exchanging data wirelessly between electronic devices via radio waves. The distance between the two devices that exchange data can in most cases be no more than ten metres.

What is the weight of the Klipsch Reference Premiere RP-8060FA?

The Klipsch Reference Premiere RP-8060FA has a weight of 32200 g.

What certifications does the Klipsch Reference Premiere RP-8060FA have?

The Klipsch Reference Premiere RP-8060FA has the following certifications: CE.

What is the height of the Klipsch Reference Premiere RP-8060FA?

The Klipsch Reference Premiere RP-8060FA has a height of 1095 mm.

What is the width of the Klipsch Reference Premiere RP-8060FA?

The Klipsch Reference Premiere RP-8060FA has a width of 277 mm.

What is the depth of the Klipsch Reference Premiere RP-8060FA?

The Klipsch Reference Premiere RP-8060FA has a depth of 503 mm.

Does the Klipsch Reference Premiere RP-8060FA have a titanium driver diaphragm?

Yes, the Klipsch Reference Premiere RP-8060FA features a titanium driver diaphragm. This ensures accurate and detailed sound reproduction, and is considered to be of high quality compared to speakers with other materials.

Can the Klipsch Reference Premiere RP-8060FA be used for both home theater and music listening?

Yes, the Klipsch Reference Premiere RP-8060FA is recommended for universal usage, making it suitable for both home theater and music listening. This versatility allows users to enjoy a wide range of audio experiences.

Is the Klipsch Reference Premiere RP-8060FA capable of producing strong bass?

Yes, the Klipsch Reference Premiere RP-8060FA has a bass reflex design, which enhances low-frequency performance. This means that it is capable of delivering powerful and impactful bass response, providing a more immersive listening experience.

How much power can the Klipsch Reference Premiere RP-8060FA handle?

The Klipsch Reference Premiere RP-8060FA has an RMS rated power of 150 Watts and a Peak Music Power Output (PMPO) of 600 Watts. This indicates that it can handle high power levels, allowing for dynamic and loud sound without distortion.

Does the Klipsch Reference Premiere RP-8060FA come with a wired connectivity option?

Yes, the Klipsch Reference Premiere RP-8060FA utilizes wired connectivity technology. This ensures a stable and reliable connection to your audio source, eliminating potential issues associated with wireless connectivity.

How do I connect the Klipsch Reference Premiere RP-8060FA speaker to my audio system?

To connect the Klipsch Reference Premiere RP-8060FA speaker to your audio system, follow these steps: 1. Determine the placement: Position the left and right main channel speakers 6 to 15 feet (1.8 to 4.6 meters) apart. You can slightly toe them in for better stereo imaging. The listening position should be about 1 to 1.5 times the distance between the speakers. Place the center channel speaker as close to the screen as possible, preferably on top of or below the screen. For the rear surround channel speakers, mount them approximately 2 feet above the listening position, either on the walls adjacent to the listening position or behind it. 2. Make the connections: Use 16-12 gauge speaker wire to connect the speakers to your amplifier. Connect the red "positive" (+) terminal of the left speaker to the corresponding red terminal of your amplifier's left channel. Connect the black "negative" (-) terminal of the left speaker to the corresponding black terminal of your amplifier's left channel. Repeat this procedure for the remaining speakers, ensuring that no bare wires touch any other terminals. 3. Dual binding posts: If your Klipsch Reference Premiere model has dual binding posts, keep the terminal connecting bar in place for single wire connection. If you plan to use bi-wire or bi-amp connection, remove the terminal connecting bar. Refer to your receiver's manual for specific instructions. 4. Amplifier compatibility: Klipsch speakers are highly efficient and compatible with a wide range of amplifiers. They are 8-ohm compatible and can handle high output levels with low distortion. However, exercise caution with the volume control to avoid damaging your hearing or speakers. Consult your dealer or amplifier manual to ensure the best compatibility for your setup. Remember to refer to the manual for further details and illustrations specific to the Klipsch Reference Premiere RP-8060FA speaker.

Why is the sound from the Klipsch Reference Premiere RP-8060FA speaker distorted?

When the sound from the Klipsch Reference Premiere RP-8060FA speaker is distorted, there could be several possible causes. Here are some steps to troubleshoot the issue: 1. Check the audio source: Ensure that the audio source (such as a CD player, TV, or receiver) is functioning properly. Make sure the volume levels are appropriate and not set too high, as this can cause distortion. 2. Verify the speaker connections: Ensure that the speaker wires are securely connected to the appropriate terminals on both the speaker and the audio source. Check for any loose or damaged connections that may affect the sound quality. 3. Adjust the equalizer settings: If your audio system has an equalizer, check the settings to ensure that they are properly adjusted. Incorrect equalizer settings can lead to distorted sound. Try adjusting the bass, treble, and other frequency levels to find the optimal balance. 4. Positioning of the speakers: Improper speaker placement can also cause sound distortion. Make sure the speakers are positioned correctly, with sufficient space around them and away from walls or other objects that may interfere with the sound. 5. Test with different audio sources: Try playing audio from different sources (such as different CDs, DVDs, or streaming services) to determine if the distortion is specific to a particular source or consistent across all sources. This can help identify if the issue lies with the speaker or the audio source. If the distortion issue persists after following these steps, it is recommended to consult the Klipsch customer support or refer to the manual for further troubleshooting guidance specific to the Klipsch Reference Premiere RP-8060FA speaker.

How do I adjust the volume on the Klipsch Reference Premiere RP-8060FA speaker?

To adjust the volume on the Klipsch Reference Premiere RP-8060FA speaker, follow these steps: 1. Locate the volume control: The volume control is typically located on the front or top panel of the speaker. It may be a physical knob, a touch-sensitive button, or a remote control. 2. Turn the volume knob: If your speaker has a physical volume knob, simply rotate it clockwise to increase the volume and counterclockwise to decrease the volume. Start with a lower volume level and gradually increase it to your desired listening level. 3. Press the volume buttons: If your speaker has touch-sensitive buttons, locate the volume up (+) and volume down (-) buttons. Press the volume up button to increase the volume and the volume down button to decrease the volume. Press and hold the buttons for continuous volume adjustment. 4. Use the remote control: If your speaker comes with a remote control, refer to the remote control manual for instructions on adjusting the volume. Typically, there will be dedicated volume up and volume down buttons on the remote control. 5. Adjust the volume on the audio source: Additionally, you can also adjust the volume on the audio source itself, such as a connected amplifier, receiver, or audio device. Refer to the user manual of your audio source for instructions on adjusting the volume. Remember to start with a lower volume level and gradually increase it to avoid sudden loud sounds. Adjust the volume to your preferred listening level for an optimal audio experience.

Why is there no sound coming from the Klipsch Reference Premiere RP-8060FA speaker?

If there is no sound coming from the Klipsch Reference Premiere RP-8060FA speaker, you can try the following steps to troubleshoot the issue: 1. Check the connections: Ensure that the speaker is properly connected to the audio source, such as an amplifier, receiver, or audio device. Verify that the cables are securely plugged into the correct audio output and input ports. 2. Confirm the power supply: Make sure the speaker is powered on and receiving power. Check the power cable connection and ensure that the power switch is in the "on" position. If the speaker has a power indicator light, check if it is illuminated. 3. Adjust the volume: Increase the volume level on the audio source and the speaker itself. Ensure that the volume is not set to the minimum or muted. 4. Test with different audio sources: Connect the speaker to different audio sources, such as a different device or audio input, to determine if the issue is specific to one source or consistent across all sources. This can help identify if the problem lies with the speaker or the audio source. 5. Consult the manual: If the above steps do not resolve the issue, refer to the Klipsch Reference Premiere RP-8060FA speaker manual for further troubleshooting guidance specific to this model. Please note that these steps are general troubleshooting suggestions and may vary depending on the specific circumstances.

How do I position the Klipsch Reference Premiere RP-8060FA speaker for optimal sound quality?

To position the Klipsch Reference Premiere RP-8060FA speaker for optimal sound quality, follow these steps: 1. Left and Right Main Channel Speakers: Place the speakers 6 to 15 feet (1.8 to 4.6 meters) apart. You can slightly toe them in for better stereo imaging. The listening position should be about 1 to 1.5 times the distance between the speakers. 2. Center Channel Speaker: Position the center channel speaker as close to the screen as possible, preferably on top of or below the screen. This ensures that dialogue and primary sounds appear to come from the video screen. 3. Rear Surround Channel Speakers: Mount the rear surround channel speakers approximately 2 feet above the listening position, either on the walls adjacent to the listening position or behind it. These speakers recreate the sense of space and ambience in your surround sound setup. 4. Speaker Wire Connection: Use 16-12 gauge speaker wire to connect the speakers to your amplifier. Connect the positive (+) terminal of the left speaker to the corresponding positive terminal of your amplifier's left channel. Connect the negative (-) terminal of the left speaker to the corresponding negative terminal of your amplifier's left channel. Repeat this procedure for the remaining speakers. 5. Amplifier Compatibility: Klipsch speakers are highly efficient and compatible with a wide range of amplifiers. However, exercise caution with the volume control to avoid damaging your hearing or speakers. Consult your dealer or amplifier manual to ensure the best compatibility for your setup. Please note that these positioning guidelines are general recommendations for optimal sound quality. Adjustments may be needed based on the specific characteristics of your room and personal preferences.

Is the manual of the Klipsch Reference Premiere RP-8060FA available in English?

Yes, the manual of the Klipsch Reference Premiere RP-8060FA is available in English .

Is your question not listed? Ask your question here

No results