Name: KitchenAid KRFC704FBS
Brand: KitchenAid
SKU: 1235376
Rating: 75 (1 reviews)

manualKitchenAid KRFC704FBS

Installation Instructions

for Pressure Regulator on Customer Supply Line

On Models: JFFCC72EFS04, JFFCC72EHL02, KRFC604FSS03, KRFC704FBS03, KRFC704FPS04, KRFC704FSS03, WRF954CIHM02, WRF954CIHB02, WRF954CIHW02, WRF954CIHV02, WRF954CIHZ03

IMPORTANT:

■ Pressure regulator kit intended for use on the above

models to assist in the dispensing of water in households

with high water pressure.

■ Connect the pressure regulator to your water supply line in

accordance with all state and local codes and ordinances.

■ Make sure to turn off water supply before installation.

Kit Contains:

A. (1) Pressure Regulator

B. (1) Mounting Clip

C. (1) Screw

D. (2) Adhesive-backed Tubing Clip

E. (1) Installation Instruction (not pictured)

F. (1) Waterline-valve-regulator (not pictured)

NOTE: Attaching the pressure regulator will require a 2”

spacing from back of appliance to the wall. This may be

greater than before installation, causing the appliance to stick

out further.

Tools Needed:

■ PEX Tube Cutter –OR– Utility Knife

■ Phillips Screwdriver

■ Small container for draining the hose

■ Copper Tubing Cutter (If copper water line)

PREPARING THE APPLIANCE FOR SERVICE

1. Unplug appliance or disconnect power.

2. Turn the water off at the household supply.

3. If servicing a refrigerator, purge the product by dispensing

water for at least 30 seconds.

4. Locate the line connecting the household supply to the

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Failure to do so can result in death or electrical shock.

Replace all parts and panels before operating.

Figure 1

product. Disconnect the supply line from the household

side, using the container to catch the draining water. Do

not disconnect from the product.

INSTALLING THE PRESSURE REGULATOR

1. Use the provided 24" (61cm) long PEX water line.

2. Using the tube cutter or utility knife, cut the household

supply line at the measurement. Ensure that tubing is

cut square with no burrs, sharp edges, or deformation to

prevent leaking.

3. For bottom mount and side-by-side platforms, locate and

remove one of the center screws holding the machine

compartment cover in place. (If not available, locate a

similar location on the product.) See Figure 2.

4. Using the existing hole, attach the mounting clip with the

provided screw. Tighten screw so that the clip does not

freely rotate. See Figure 3.

5. Connect the pressure regulator in between the loose ends

of the water line by pressing the line ends rmly into the

pressure regulator’s connectors. See Figure 4.

IMPORTANT: Ensure that the water ow direction indicator

arrow on the pressure regulator is pointing in the direction of

the water ow (towards the appliance). Verify that the

connection is properly made by gently attempting to pull the

line straight out. If the line remains connected, the connection

was properly made.

EXAMPLE OF MOUNTING CLIP LOCATION

MOUNTING CLIP ATTACHED WITH SCREW

CONNECTING PRESSURE REGULATOR

FROM

SUPPLY

APPLIANCE

WATER FLOW DIRECTION INDICATOR ARROW

W11502228A

Figure 2

Figure 4

Figure 3

View the manual for the KitchenAid KRFC704FBS here, for free. This manual comes under the category refrigerators and has been rated by 1 people with an average of a 7.5. This manual is available in the following languages: English. Do you have a question about the KitchenAid KRFC704FBS or do you need help? Ask your question here

Need help?

Do you have a question about the KitchenAid and the answer is not in the manual? Ask your question here. Provide a clear and comprehensive description of the problem and your question. The better your problem and question is described, the easier it is for other KitchenAid owners to provide you with a good answer.

Anthony Glorioso • 22-1-2023No comments

Ice and water not working Display on door not working What could be wrong

View photo

Answer this question

Tom • 18-5-2023No comments

Ice maker does not make ice

Answer this question

Mario • 24-12-2022No comments

My refrigerator area is not cooling and no air is coming out from air vent

Answer this question

Shelly Mincy • 15-11-2022No comments

I have a Kitchenaid French Door Model KRFC704FBS and I just replaced the water/ice filter and now the indoor ice and water dispenser does not work???

Answer this question

Brynn • 4-11-2022No comments

I need the part number for the removable bins that fit into the silver door shelves

Answer this question

Winford • 13-6-2022No comments

My new fridge wont get cold

Answer this question

Winford Ross • 13-6-2022No comments

Fridge no cold

Answer this question

Brenda Murry • 31-3-20221 comment

How do you put the time of day on door

Anthony • 12-6-2022

How do you adjust the right door hinge to open only to 45 degrees and stop

Answer this question

Christine Jones • 10-10-2021No comments

How do you replace the secondary fan?

Answer this question

Laurie Cardin • 10-1-20212 comments

Is there a “reset” for the ice maker?

Antonio Gonzalez • 2-9-2021

The ice maker is not working

Brynn • 4-11-2022

What is the part number for the removable door bins that fit into the metal door shelves on a kitchen aide model KRFC704FBS00

Answer this question

Number of questions: 10

General

	KitchenAid
	KRFC704FBS
	refrigerator
	English
	User manual (PDF), Instructions / Assembly (PDF), Warranty information (PDF), Datasheet (PDF), Energy label (PDF)

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the KitchenAid KRFC704FBS below.