Kentix KMS-DOOR-B manual

Kentix KMS-DOOR-B
7.2 · 1
PDF manual
 · 132 pages
English
manualKentix KMS-DOOR-B
Wired components (IP Wall Reader)
By clicking „+“ the search for available devices is started. On a „Master-Slave“ system additionally the
corresponding AccessPoint has to be selected. After about 10-20 seconds the configuration interface of the
device will be shown.#
If this is not the case, please wait until the AccessPoint stops the search-mode (60 seconds) and repeat the
process.
When the device is found it can directly be configured. This can also be done later by clicking on the pencil next
to the corresponding device.
The single settings of a DoorLock’s configuration interface are described here:
Default teach-in DoorLock
When learning new RFID-Tokens for the users this device is always displayed at first in the selection.
Double authentication (IP Wall Reader only)
At an IP Wall Reader doors can be opened using a PIN code or RFID media.
Activating the option double authentication, both types of authentication will be required for a successful
opening.
Name
Enter a name for the DoorLock-device. Typically this corresponds to the installation place.
Couple Time
Select the desired time (3 / 6 / 12 seconds), for which a device shall stay engaged after a valid booking.
Booking switches Alarmzone
If desired, an arm-/disarm-switching of a Kentix alarm system can be triggered by a booking.
The AlarmManager communication has to be activated for this in the „Configuration“ section.
Choose the desired Alarmzone here. If no Alarmzone is displayed, press the refresh-button to update the zone
selection. The usage of the function is described on the next page.
Time control Active
A Kentix DoorLock component can be configured to stay permanently engaged. The door can then be opened
without a booking at the RFID reader.
For this operating mode a time profile can be chosen here which determines the times to which the door can be
opened without additional authorization.
Switch output on booking
The Kentix AccessPoint has 2 relay outputs. These can by switched/activated by a booking (e.g. in combination
with a wall reader), to control external components (motor locks, barriers).
You can choose between two switching outputs at the AccessPoint.
External alarm system control
The 2 relay outputs can also be used to control 3rd party alarm systems. The outputs here work in a so-called
channel mode, which means that they will stay in a permanently open or closed stay when switched.
The usage of the function is described on the next page.!
Page (11-2017, subject to change) kentix.com95
NOTE!
To enable the permanent coupling, a valid booking has to be performed within the selected time profile.
Without a booking the door remains closed.

DoorLock

NOTE!
Please note, that DIP switch 1 or 2 has to be set inside the reader for detection and communication
between reader and network relay module.

Manual

View the manual for the Kentix KMS-DOOR-B here, for free. This manual comes under the category door / window sensors and has been rated by 1 people with an average of a 7.2. This manual is available in the following languages: English. Do you have a question about the Kentix KMS-DOOR-B or do you need help? Ask your question here

Index

Need help?

Do you have a question about the Kentix and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Kentix KMS-DOOR-B specifications

Below you will find the product specifications and the manual specifications of the Kentix KMS-DOOR-B.

General
BrandKentix
ModelKMS-DOOR-B | KMS-DOOR-B
Productdoor / window sensor
EAN4260300580404
LanguageEnglish
FiletypeUser manual (PDF)
Features
Product colorBlack
Connectivity technologyWireless
LED indicatorsYes
Alarm decibels65 dB
Operating frequency2300 MHz
InterfaceZigBee
Power
Battery technologyLithium-Ion (Li-Ion)
Number of batteries supported1
Battery voltage3.6 V
Weight & dimensions
Width62 mm
Depth62 mm
Height27 mm
Weight50 g
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Kentix KMS-DOOR-B below.

What is the weight of the Kentix KMS-DOOR-B?

The Kentix KMS-DOOR-B has a weight of 50 g.

What is the height of the Kentix KMS-DOOR-B?

The Kentix KMS-DOOR-B has a height of 27 mm.

What is the width of the Kentix KMS-DOOR-B?

The Kentix KMS-DOOR-B has a width of 62 mm.

What is the depth of the Kentix KMS-DOOR-B?

The Kentix KMS-DOOR-B has a depth of 62 mm.

Is the manual of the Kentix KMS-DOOR-B available in English?

Yes, the manual of the Kentix KMS-DOOR-B is available in English .

Is your question not listed? Ask your question here

No results