Kentix KMS-DOOR-B manual

Kentix KMS-DOOR-B
7.2 · 1
PDF manual
 · 132 pages
English
manualKentix KMS-DOOR-B

9.3.1.2. Initial setup - Master card set

No
Step
Note / Signalization
1
Present Servicekey card (yellow) in front of DoorLock-
devices reading unit.
This step has to be performed only one time at the
initial setup.
At a door lever, wall reader or cabinet lock the initial
setup is completed with this step.
2
Present Servicekey card (yellow) again in front of knob
to start programming mode.
3
Present Battery replacement card (green) in front of
knob.
4
Present Disassembly card (blue) in front of knob.
5
Present Servicekey card (yellow) in front of knob to
leave programming mode.
2x short sound, LEDs light up green
then wait for 5 seconds
1x short sound, 1x long sound
then wait for 5 seconds
2x short sound, 1x long sound
then wait for 5 seconds
1x short sound, 1x long sound
2x short sound, LEDs light up green
then wait for 5 seconds
Page (11-2017, subject to change) kentix.com88

DoorLock

NOTE!

For the initial setup of door levers, wall readers or cabinet locks the teaching of battery changing and

dismantling card is not required. The door lever has to be woken up by presenting any RFID card in front of the

reader unit. Then the servicekey card must be held in front of it for one time. After this the process is finished.

As the wall reader is permanently powered a wakeup with a RFID card is not necessary.

At a cabinet lock the wakeup button has to be pressed before holding the Servicekey card in front of the

reader.

If the initial programming leads to an error, a DoorLock-device can be reset using the Servicekey card. Please

read the chapter „Reset of components“ later in this manual.

Manual

View the manual for the Kentix KMS-DOOR-B here, for free. This manual comes under the category door / window sensors and has been rated by 1 people with an average of a 7.2. This manual is available in the following languages: English. Do you have a question about the Kentix KMS-DOOR-B or do you need help? Ask your question here

Index

Need help?

Do you have a question about the Kentix and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Kentix KMS-DOOR-B specifications

Below you will find the product specifications and the manual specifications of the Kentix KMS-DOOR-B.

General
BrandKentix
ModelKMS-DOOR-B | KMS-DOOR-B
Productdoor / window sensor
EAN4260300580404
LanguageEnglish
FiletypeUser manual (PDF)
Features
Product colorBlack
Connectivity technologyWireless
LED indicatorsYes
Alarm decibels65 dB
Operating frequency2300 MHz
InterfaceZigBee
Power
Battery technologyLithium-Ion (Li-Ion)
Number of batteries supported1
Battery voltage3.6 V
Weight & dimensions
Width62 mm
Depth62 mm
Height27 mm
Weight50 g
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Kentix KMS-DOOR-B below.

What is the weight of the Kentix KMS-DOOR-B?

The Kentix KMS-DOOR-B has a weight of 50 g.

What is the height of the Kentix KMS-DOOR-B?

The Kentix KMS-DOOR-B has a height of 27 mm.

What is the width of the Kentix KMS-DOOR-B?

The Kentix KMS-DOOR-B has a width of 62 mm.

What is the depth of the Kentix KMS-DOOR-B?

The Kentix KMS-DOOR-B has a depth of 62 mm.

Is the manual of the Kentix KMS-DOOR-B available in English?

Yes, the manual of the Kentix KMS-DOOR-B is available in English .

Is your question not listed? Ask your question here

No results