Kentix KMS-DOOR-B manual

Kentix KMS-DOOR-B
7.2 · 1
PDF manual
 · 132 pages
English
manualKentix KMS-DOOR-B

5.8. MultiSensor-Rack

The MultiSensor-RACK can be operated as stand alone device, but also in combination with an AlarmManager-
PRO. The AlarmManager then controls the environmental sensors.
For configuration in stand alone operation a web server is integrated, which allows you to control and setup the
device via LAN and a web browser.
Over the SNMP interface, an integration in network management systems is possible.

5.8.1. Safety note and installation

In case of a power failure, the settings are not lost. Energized relays drop out and go back when the power
returns to the unswitched, closed output state.
To bridge longer downtimes, use a suitable UPS system.
In case of an equipment failure an uninterruptible power supply to the connected devices is ensured by the
closed state of the relays.
To ensure the security and integrity of the operator and the correct operation of the KENTIX MultiSensor-RACK,
the execution of the installation only has to be done by an expert. Also ensure that the relevant requirements
are met.
Connection via PC: Connect the LAN jack from the MultiSensor-RACK over a LAN cable with your
network and your PC. Pay attention that you have to use a Cross-Over network
cable, by a direct connection.
Set the IP address of your PC to e.g. „192.168.100.123“.

5.8.2. Default settings

Voltage supply: Basic voltage supply realized with PDU-1 power input
Default IP-address: 192.168.100.223
Subnet mask: 255.255.255.0
Gateway: 192.168.100.1
User: admin
Password: password
Page (11-2017, subject to change) kentix.com40
IMPORTANT! - Reset to factory defaults
If you have forgotten the IP-address or login information of the MultiSensor-RACK, you can reset the device to
factory defaults.#
To do this press both buttons for the display control at the same time and hold them down.#
After 10 seconds a security prompt is displayed. By pressing the right button the MultiSensor will then be reset
to factory defaults.
After this procedure the device will restart and can then be accessed via the default settings.

MultiSensors

Manual

View the manual for the Kentix KMS-DOOR-B here, for free. This manual comes under the category door / window sensors and has been rated by 1 people with an average of a 7.2. This manual is available in the following languages: English. Do you have a question about the Kentix KMS-DOOR-B or do you need help? Ask your question here

Index

Need help?

Do you have a question about the Kentix and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Kentix KMS-DOOR-B specifications

Below you will find the product specifications and the manual specifications of the Kentix KMS-DOOR-B.

General
BrandKentix
ModelKMS-DOOR-B | KMS-DOOR-B
Productdoor / window sensor
EAN4260300580404
LanguageEnglish
FiletypeUser manual (PDF)
Features
Product colorBlack
Connectivity technologyWireless
LED indicatorsYes
Alarm decibels65 dB
Operating frequency2300 MHz
InterfaceZigBee
Power
Battery technologyLithium-Ion (Li-Ion)
Number of batteries supported1
Battery voltage3.6 V
Weight & dimensions
Width62 mm
Depth62 mm
Height27 mm
Weight50 g
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Kentix KMS-DOOR-B below.

What is the weight of the Kentix KMS-DOOR-B?

The Kentix KMS-DOOR-B has a weight of 50 g.

What is the height of the Kentix KMS-DOOR-B?

The Kentix KMS-DOOR-B has a height of 27 mm.

What is the width of the Kentix KMS-DOOR-B?

The Kentix KMS-DOOR-B has a width of 62 mm.

What is the depth of the Kentix KMS-DOOR-B?

The Kentix KMS-DOOR-B has a depth of 62 mm.

Is the manual of the Kentix KMS-DOOR-B available in English?

Yes, the manual of the Kentix KMS-DOOR-B is available in English .

Is your question not listed? Ask your question here

No results