Kentix KMS-DOOR-B manual

Kentix KMS-DOOR-B
7.2 · 1
PDF manual
 · 132 pages
English
manualKentix KMS-DOOR-B
E-Mail
If the MultiSensor should be able to send e-mails in the case of alarm to a configured user, it is necessary to set
an e-mail server (SMTP or ESMTP). When you have set a DNS server, which is configured in the DNS settings,
you can use the DNS name of the e-mail server here. With using ESMTP you can here enter the e-mail access
data, which you can obtain from your e-mail provider. Depending on the E-mail server, a encryption method
might be necessary. When choosing an encryption mode (STARTTLS / SSL) the required port will be set to the
default port. The port can be changed to another one when needed.
Pay attention that many mail servers need an existing sender address to send an e-mail correctly.
In the subject of the e-mail the corresponding alarm text can be found and in the mail text all measurements
from the MultiSensor are included.
E-Mail Signature
Enter a signature, which is sent with every alarm E-Mail. The signature is limited to 300 signs length.
SNMP settings
Configuration of the Simple Network Management Protocols. The MultiSensor-LAN is able to send alarm
messages as SNMP-Traps. Enter both SNMP host addresses for this. Further the sensor can be prompted or
partially configured via SNMP. The functions which are available for the SNMP communication are specified in
the supplied MIB (Management Information Base). It is available on the integrated FTP server or as download
from the Kentix website.

5.6.4. Configuration - MultiSensor (Sensor- and alarm settings)

In the following settings you can set the limit and action values for the alerting.
When an alarm is triggered, an e-mail will be sent to the configured persons and the internal buzzer is activated.
Sensor-Temperature, Humidity, Dew-point
Set the alarm limit values. Alarm will be triggered when the measurements undershot or exceeded the limits.
The temperature hysteresis is 1°C, humidity hysteresis 1%.
The dew-point is calculated with the current temperature and the relative humidity from the sensor.
If the room temperature approximates to the difference of the set dew-point hysteresis (2°C default) an alarm
will be triggered. Systems and devices can lead to condensation, when the dew point temperature approximates
the room temperature.
Sensor-Carbon Monoxide
Alarm settings for the Carbon Monoxide. The sensitivity can be set from 0% to 100% and will be triggered by
exceeding. CO is measured from about 10ppm. There is no exact measurement of the CO content. The
measurement is construed to the highest sensitivity and can be changed slightly in the adjustment.!
Carbon Monoxide concentrations like they emerge in fires are detected even at 100% setting.!
10%: Minimal concentration of around 20-50ppm lead to an alarm trigger.!
100%: Concentrations of 200-400ppm lead to an alarm trigger.
Sensor-Motion
Limit value for the integrated PIR (passive infra-rot) motion detection. It is triggered when exceeded. Objects
which have a temperature difference of about 4°C to the environment temperature and which are bigger than
250x400mm will be detected. For a safe detection of persons, the value should be in the range of 30-50%.
The detection range is about 100°.
Page (11-2017, subject to change) kentix.com32

MultiSensors

Manual

View the manual for the Kentix KMS-DOOR-B here, for free. This manual comes under the category door / window sensors and has been rated by 1 people with an average of a 7.2. This manual is available in the following languages: English. Do you have a question about the Kentix KMS-DOOR-B or do you need help? Ask your question here

Index

Need help?

Do you have a question about the Kentix and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Kentix KMS-DOOR-B specifications

Below you will find the product specifications and the manual specifications of the Kentix KMS-DOOR-B.

General
BrandKentix
ModelKMS-DOOR-B | KMS-DOOR-B
Productdoor / window sensor
EAN4260300580404
LanguageEnglish
FiletypeUser manual (PDF)
Features
Product colorBlack
Connectivity technologyWireless
LED indicatorsYes
Alarm decibels65 dB
Operating frequency2300 MHz
InterfaceZigBee
Power
Battery technologyLithium-Ion (Li-Ion)
Number of batteries supported1
Battery voltage3.6 V
Weight & dimensions
Width62 mm
Depth62 mm
Height27 mm
Weight50 g
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Kentix KMS-DOOR-B below.

What is the weight of the Kentix KMS-DOOR-B?

The Kentix KMS-DOOR-B has a weight of 50 g.

What is the height of the Kentix KMS-DOOR-B?

The Kentix KMS-DOOR-B has a height of 27 mm.

What is the width of the Kentix KMS-DOOR-B?

The Kentix KMS-DOOR-B has a width of 62 mm.

What is the depth of the Kentix KMS-DOOR-B?

The Kentix KMS-DOOR-B has a depth of 62 mm.

Is the manual of the Kentix KMS-DOOR-B available in English?

Yes, the manual of the Kentix KMS-DOOR-B is available in English .

Is your question not listed? Ask your question here

No results