Kentix KMS-DOOR-B manual

Kentix KMS-DOOR-B
7.2 · 1
PDF manual
 · 132 pages
English
manualKentix KMS-DOOR-B

5.3. Calibration of the temperature / humidity sensor!

For the devices MultiSensor-RF / -LAN / -LAN-RF and -RACK it might be necessary to calibrate the sensor for
temperature and humidity once after installation and commissioning.
For this the temperature must be determined (for example with an infrared thermometer) in the immediate
vicinity of the MultiSensor. The difference between the two measured temperatures (measuring device and
MultiSensor) is then entered as an offset in full degrees into the corresponding field in the ControlCenter or in
the web interface of the MultiSensor (stand-alone).
The correction also has a direct influence on the determined humidity.

5.4. Kentix system jack at MultiSensor-RF / -LAN / -LAN-RF

Via the Kentix system jack, located in the front of the MultiSensor-RF, system components such as leakage
detectors, door contacts, acoustic signals or alarms of USPs or climate devices can be connected. The
MultiSensor-RF is powered via the Kentix system jack.
To connect external devices or alarm in- or outputs, three connector modules are available:
1) Power-Adapter KIO 1: Power supply, 2 digital inputs
2) Power-Adapter KIO 2: Power supply only
3) Power-Adapter KIO 3: Power supply, 2 digital inputs and 2 relay outputs
1 - Internal system voltage (GND)
2 - Alarm output 1 (Open Collector 100mA)
3 - Alarm output 2 (Open Collector 100mA)
4 - Power supply 10-32VDC (+/-)
5 - Power supply 10-32VDC (+/-)
6 - Alarm input 1 (External dry contact, no/nc)
7 - Alarm input 2 (External dry contact, no/nc)
8 - Internal system voltage (5V)
KENTIX system jack
Page (11-2017, subject to change) kentix.com27

MultiSensors

NOTE!
The MultiSensor is already pre-calibrated for the recommended installation on the ceiling. If there is no external
influence (e.g. by the airflow of the air conditioning system), the sensor will show the correct temperature.
Depending on the orientation of the MultiSensor (wall mounting, test operation with lateral position or cover up) and the
conditions in the room (climate control), a correction by several degrees may be necessary.

MultiSensors

Manual

View the manual for the Kentix KMS-DOOR-B here, for free. This manual comes under the category door / window sensors and has been rated by 1 people with an average of a 7.2. This manual is available in the following languages: English. Do you have a question about the Kentix KMS-DOOR-B or do you need help? Ask your question here

Index

Need help?

Do you have a question about the Kentix and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Kentix KMS-DOOR-B specifications

Below you will find the product specifications and the manual specifications of the Kentix KMS-DOOR-B.

General
BrandKentix
ModelKMS-DOOR-B | KMS-DOOR-B
Productdoor / window sensor
EAN4260300580404
LanguageEnglish
FiletypeUser manual (PDF)
Features
Product colorBlack
Connectivity technologyWireless
LED indicatorsYes
Alarm decibels65 dB
Operating frequency2300 MHz
InterfaceZigBee
Power
Battery technologyLithium-Ion (Li-Ion)
Number of batteries supported1
Battery voltage3.6 V
Weight & dimensions
Width62 mm
Depth62 mm
Height27 mm
Weight50 g
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Kentix KMS-DOOR-B below.

What is the weight of the Kentix KMS-DOOR-B?

The Kentix KMS-DOOR-B has a weight of 50 g.

What is the height of the Kentix KMS-DOOR-B?

The Kentix KMS-DOOR-B has a height of 27 mm.

What is the width of the Kentix KMS-DOOR-B?

The Kentix KMS-DOOR-B has a width of 62 mm.

What is the depth of the Kentix KMS-DOOR-B?

The Kentix KMS-DOOR-B has a depth of 62 mm.

Is the manual of the Kentix KMS-DOOR-B available in English?

Yes, the manual of the Kentix KMS-DOOR-B is available in English .

Is your question not listed? Ask your question here

No results