Kentix KMS-DOOR-B manual

Kentix KMS-DOOR-B
7.2 · 1
PDF manual
 · 132 pages
English
manualKentix KMS-DOOR-B

4.10. SMS commands for remote control of AlarmManager

The AlarmManager reports not only all the alarms via SMS, it can be also remotely controlled via simple SMS

commands from a mobile phone. This brings the big advantage of having the central alarm system in your

pocket and remotely setting the system to the desired states.

The AlarmManager can be armed or disarmed and alarms can be acknowledged remotely. So you can decide if

it is necessary to intervene on the ground at any time by using the SMS information and status inquiry.

Important notes for remote control of the AlarmManagers via SMS

Upper- and lower-case can be used.

Between „Operator-PIN“ and „COMMAND“ is always a space.

The „Operator-PIN“ can have 4-8 alphanumerical characters. Setup the PIN with the ControlCenter.

The AlarmManager is confirming each command SMS with an SMS back to the sender.

Command SMS with the wrong phone number or password will not be confirmed for security reasons.

SMS control commands

Example: Arm-disarming of the AlarmManager via SMS command"

SMS command
Description
Example
Confirmation
{PIN} ON
Arming of the AlarmManagers. All zones will be
armed.
1234 on
OK! ARM All Zones
{PIN} ON{ZONE}
Arming of the selected zone.
1234 on1
OK! ARM ZONE 1
{PIN} OFF
Disarming of all zones.
1234 off
OK! DISARM All Zones
{PIN} QUIT
Acknowledge of all pending alarms. The alarm
repetition is terminated.
The AlarmManager can be set to arm state again.
1234 quit
OK! ALARM QUIT
{PIN} STATE
The AlarmManager sends the actual system state.
1234 state
OK! ARMED/DISARMED/
ALARM
{PIN} MSTATE1-n
The AlarmManager sends the actual system state
and values of a MultiSensor.
Enter the number of the MultiSensor (1-100)
directly after the command „MSTATE“."
The response contains the name of the
MultiSensor.
1234 mstate1
OK! SENSORNAME:
TEMP=20C
REL-HUM=25%
DEW-POINT=3C
MOTION=15%
EXT-IN=0
SABOTAGE=0
POWER=OK
Page (11-2017, subject to change) kentix.com18

NOTE!

When a sensor sends an alarm, the SMS contains the number of the sensor to send a mstate request.

The AlarmManager

1234 on

SMS command

Manual

View the manual for the Kentix KMS-DOOR-B here, for free. This manual comes under the category door / window sensors and has been rated by 1 people with an average of a 7.2. This manual is available in the following languages: English. Do you have a question about the Kentix KMS-DOOR-B or do you need help? Ask your question here

Index

Need help?

Do you have a question about the Kentix and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Kentix KMS-DOOR-B specifications

Below you will find the product specifications and the manual specifications of the Kentix KMS-DOOR-B.

General
BrandKentix
ModelKMS-DOOR-B | KMS-DOOR-B
Productdoor / window sensor
EAN4260300580404
LanguageEnglish
FiletypeUser manual (PDF)
Features
Product colorBlack
Connectivity technologyWireless
LED indicatorsYes
Alarm decibels65 dB
Operating frequency2300 MHz
InterfaceZigBee
Power
Battery technologyLithium-Ion (Li-Ion)
Number of batteries supported1
Battery voltage3.6 V
Weight & dimensions
Width62 mm
Depth62 mm
Height27 mm
Weight50 g
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Kentix KMS-DOOR-B below.

What is the weight of the Kentix KMS-DOOR-B?

The Kentix KMS-DOOR-B has a weight of 50 g.

What is the height of the Kentix KMS-DOOR-B?

The Kentix KMS-DOOR-B has a height of 27 mm.

What is the width of the Kentix KMS-DOOR-B?

The Kentix KMS-DOOR-B has a width of 62 mm.

What is the depth of the Kentix KMS-DOOR-B?

The Kentix KMS-DOOR-B has a depth of 62 mm.

Is the manual of the Kentix KMS-DOOR-B available in English?

Yes, the manual of the Kentix KMS-DOOR-B is available in English .

Is your question not listed? Ask your question here

No results