Kentix KMS-DOOR-B manual

Kentix KMS-DOOR-B
7.2 · 1
PDF manual
 · 132 pages
English
manualKentix KMS-DOOR-B

4.3. Communication- / Network ports

For the configuration and firmware updates and also the communication between#

MultiSensors (-LAN / -LAN-RF / -RACK) the following ports are used. These ports eventually have to be taken

into account for the configuration of your network.

In combination with the Kentix360 Cloud additional ports for configuration and connection to the Cloud are

required.

4.4. Default settings / Factory defaults

Default IP-address: 192.168.100.222

Subnet mask: 255.255.255.0

User: admin

Password: password

Setup IP-Address: Change IP settings in the Kentix Control center opening#

„System“ -> „Settings“ -> „Network...“ in the menu.

No
Description
Port number
1
Configuration AlarmManager via ControlCenter, firmwareupdate
TCP 21, 80, 2101#
from PC to AlarmManager
2
Access to web-interface of AlarmManager / MultiSensors
TCP 80, 443
from PC to AlarmManager / MultiSensors
3
Data transfer between MultiSensors and AlarmManager
TCP 80
4
Request of measurement values via SNMP (network monitoring) from
AlarmManager / MultiSensors
TCP 161 (from SNMP-Tool to AlarmManager or
MultiSensor)
No
Description
Port number
1
Configuration of the Kentix360 Cloud via ControlCenter
TCP 80, 443#
from PC to Internet („mykentix.com“)
2
Communication between AlarmManager/AccessPoint or mobile app to
cloud
TCP 5222 to the Internet#
(„mykentix.com“)
Page (11-2017, subject to change) kentix.com13

Reset to factory defaults (Firmware version 5.60.00 an earlier)

To reset the AlarmManager to factory defaults, press the RESET Button on the back of the board and hold it

down for 5 seconds. The device will be set to factory defaults and restarts. After about 30 seconds the

AlarmManager can be accessed again via the default settings.

Reset to factory defaults (Firmware version 5.70.00 and higher)

To reset the AlarmManager to factory defaults, press the RESET Button on the back of the board and hold it

down for 10 seconds. While holding the button, the Alarm-LED will start blinking. After the time has run up the

reset is quit by a sound. The RESET Button can then be released.#

The device will be set to factory defaults and restarts. After about 30 seconds the AlarmManager can be

accessed again via the default settings.

The AlarmManager

Manual

View the manual for the Kentix KMS-DOOR-B here, for free. This manual comes under the category door / window sensors and has been rated by 1 people with an average of a 7.2. This manual is available in the following languages: English. Do you have a question about the Kentix KMS-DOOR-B or do you need help? Ask your question here

Index

Need help?

Do you have a question about the Kentix and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Kentix KMS-DOOR-B specifications

Below you will find the product specifications and the manual specifications of the Kentix KMS-DOOR-B.

General
BrandKentix
ModelKMS-DOOR-B | KMS-DOOR-B
Productdoor / window sensor
EAN4260300580404
LanguageEnglish
FiletypeUser manual (PDF)
Features
Product colorBlack
Connectivity technologyWireless
LED indicatorsYes
Alarm decibels65 dB
Operating frequency2300 MHz
InterfaceZigBee
Power
Battery technologyLithium-Ion (Li-Ion)
Number of batteries supported1
Battery voltage3.6 V
Weight & dimensions
Width62 mm
Depth62 mm
Height27 mm
Weight50 g
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Kentix KMS-DOOR-B below.

What is the weight of the Kentix KMS-DOOR-B?

The Kentix KMS-DOOR-B has a weight of 50 g.

What is the height of the Kentix KMS-DOOR-B?

The Kentix KMS-DOOR-B has a height of 27 mm.

What is the width of the Kentix KMS-DOOR-B?

The Kentix KMS-DOOR-B has a width of 62 mm.

What is the depth of the Kentix KMS-DOOR-B?

The Kentix KMS-DOOR-B has a depth of 62 mm.

Is the manual of the Kentix KMS-DOOR-B available in English?

Yes, the manual of the Kentix KMS-DOOR-B is available in English .

Is your question not listed? Ask your question here

No results