Power on/off, Channel up/down, Menu on/off, Arrow buttons, OK/Enter, Back, Guide (EPG),
TV/DVD (TV/VCR button), Sub Title (Sub T.), Open/Close ( ), Rewind ( ), Playback ( ),
Forward ( ), Record ( ), Stop ( ), Still ( ).
Power on/off, Volume up/down, Muting, DVD operation buttons: Menu on/off, Arrow buttons,
OK/Enter, Back, Sub Title (Sub T.), Open/Close ( ), Rewind ( ), Playback ( ),
Forward ( ), Stop ( ), Still ( ).
STB
VCR
DVD
AUDIO
DeviceModeApplied for these functionsPage
* DVR button only applies to JVC DVR (Dish Satellite STB).
70
71, 72
73
74
You can program your remote control to operate your external devices, using the instructions
and codes on pages 70 - 74. The following external devices can be operated using your
remote control.
Remote programming
Notes:
• To record to your VCR or DVD, hold the record ( l ) button on the remote control and press play
( ® ).
• If the code you programmed doesn't work, try the next one. If no codes work, refer to "Search
Code Function" on page 69. If your remote does not work after using the "Search Code Function",
use the remote that came with your device. Your TV remote cannot be guaranteed to work with all
models, brands or operations.
• When the television remote control does not operate, for a model that allows you to switch the
remote control code on the device side, you can try switching the setting to default or something
else on the device side.
1) Find your device and device's brand from the code list. See page 70 - 74.
2) Select the mode of your device by pressing the MODE button. Then confirm the mode LED on the
remote control.
3) Press and hold the TUNE button, then enter the first four digit code number listed using the
number buttons. When the code is set, the mode LED goes out for a second, then it lights.
4) After confirming the proper mode LED, release the TUNE button, and confirm the operation of your
device.
5) If your device does not respond, try and enter the next code.
1) Select a mode of your device by pressing the MODE button.
2) Press the P
OWER and RETURN+/TV buttons. Hold for at least 3 seconds and release. Then confirm
the mode LED blinks.
3) Press any button* on the remote, and see if the selected device responds. *Use the applied
buttons except for √ ® cursors, Return+/TV and Rec ( l ) on the above chart.
4) If there was a response, press RETURN+/TV. The codes are now set. Then confirm the mode
LED goes out.
5) If there was no response, try to select the previous code or the next code by using √or ® . If you
repeat a total of 65 times for the STB (90 times for the VCR, 120 times for the DVD and 132 times
for the AUDIO) without a response, use the remote control that came with your equipment. Press
RETURN+/TV to exit. Then confirm the mode LED goes out.
Search Code Function
How to set the codes
Manual
View the manual for the JVC LT-37X898 here, for free. This manual comes under the category televisions and has been rated by 1 people with an average of a 7.3. This manual is available in the following languages: English. Do you have a question about the JVC LT-37X898 or do you need help? Ask your question here
Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the JVC LT-37X898 below.
What's the best viewing distance for my JVC television?
The ideal viewing distance for your JVC television depends on the screen size. As a rule of thumb you can assume that approximately 2.4 times the screen diagonal is the ideal viewing distance.
My television has no signal anymore, now what?
If your television has no signal, you can check the following: - Check whether your television is set to the correct source. - Check if your TV receiver is properly connected via the HDMI or SCART input.
What screen dimensions does my television have?
The size of your television is usually expressed in inches, 1 inch is 2.54 centimetres. The size is the diagonal size of your television, so you measure the screen from bottom left to top right.
What is HDMI?
HDMI stands for High-Definition Multimedia Interface. An HDMI cable is used to transport audio and video signals between devices.
Can bluetooth devices of different brands be connected to each other?
Yes, bluetooth is a universal method that allows different devices equipped with bluetooth to connect to each other.
Is the manual of the JVC LT-37X898 available in English?
Yes, the manual of the JVC LT-37X898 is available in English .
Need help?
Do you have a question about the JVC and is the answer not in the manual?
Question and answer
Number of questions: 0