JVC KW-M540BT manual

JVC KW-M540BT
7.6 · 7
PDF manual
 · 52 pages
English
manualJVC KW-M540BT
ENGLISHi

Important NoticeImportant Notice

To ensure proper use, please read through this
manual before using this product. It is especially
important that you read and observe WARNINGS
and CAUTIONS in this manual.
Please keep the manual in a safe and accessible
place for future reference.

WARNINGS

To prevent accidents and damages
• DO NOT install any unit or wire any cable in a
location where;
it may obstruct the steering wheel and gearshift
lever operations.
it may obstruct the operation of safety devices such
as air bags.
it may obstruct visibility.
• DO NOT raise the volume level too much, as this will
make driving dangerous by blocking outside sounds,
and may cause hearing loss.
• DO NOT operate the unit while driving. If you need
to operate the unit while driving, be sure to look
around carefully.
• Stop the car before performing any complicated
operations.
• The driver must not watch the monitor while driving.

CAUTIONS

To care for the unit
• If you have parked the car for a long time in hot or
cold weather, wait until the temperature in the car
becomes normal before operating the unit.
To care for the monitor
• The monitor built into this unit has been produced
with high precision, but it may have some ineffective
dots. This is inevitable and is not considered
defective.
• Do not expose the monitor to direct sunlight.
• Do not operate the touch panel using a ball-point
pen or similar tool with a sharp tip.
Touch the keys on the touch panel with your finger
directly (if you are wearing a glove, take it off).
• When the temperature is very cold or very hot...
Chemical changes occur inside, causing
malfunction.
Pictures may not appear clearly or may move
slowly. Pictures may not be synchronized with
the sound or picture quality may decline in such
environments.
On the volume setting
• Digital devices produce very little noise compared
with other sources. Lower the volume before playing
these digital sources to avoid damaging the speakers
by sudden increase of the output level.
For Israel
02_KW_M540BT_E_SAFETY.indd i02_KW_M540BT_E_SAFETY.indd i 12/13/2017 11:33:19 AM12/13/2017 11:33:19 AM

Manual

View the manual for the JVC KW-M540BT here, for free. This manual comes under the category car radios and has been rated by 7 people with an average of a 7.6. This manual is available in the following languages: English. Do you have a question about the JVC KW-M540BT or do you need help? Ask your question here

Need help?

Do you have a question about the JVC and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 4
A
Abdul AsisNovember 29, 2021

After replacing the battery, a password request appears but I don't know the code because I am the second owner... and I don't know the contact number of the first owner... How can I reset it?

After replacing the battery, a password request appears but I don't know the code because I am the second owner... and I don'...
zoom-in
View photo
This message has been automatically translated
N
Norbert AlvinOctober 3, 2022

JVC KW-M540BT car radio, I cannot enter its function menu. When the ACC position is on, it can only turn on with the safety warning. The touch screen feature is not working. What is the solution? Thank you.

JVC KW-M540BT car radio, I cannot enter its function menu.
When the ACC position is on, it can only turn on with the safety w...
zoom-in
View photo
This message has been automatically translated
S
ShahanasJanuary 28, 2023

How to reset jvc m540bt

R
RefDecember 25, 2023

No Sound

JVC KW-M540BT specifications

Below you will find the product specifications and the manual specifications of the JVC KW-M540BT.

The JVC KW-M540BT is a car radio that offers a range of features and sleek design. With Bluetooth capability, it allows users to easily connect their devices for hands-free calling and audio streaming. The radio's Bluetooth version 3.0+HS ensures a stable connection and supports various Bluetooth profiles including A2DP, AVRCP, and PBAP. Designed in a 2 DIN size, this car radio fits seamlessly into compatible car models. It features a rear USB port, providing convenient access for charging devices and playing media. The radio supports FM, LW, and MW radio bands, allowing users to tune in to their favorite stations. Additionally, the Radio Data System (RDS) feature displays useful information, such as station names and song titles. With a preset stations quantity of 24, users can easily save and switch between their preferred radio stations. The JVC KW-M540BT also supports MP3 playback, enabling users to enjoy their favorite music files directly from a USB device. In terms of power, the car radio offers a maximum of 50 W per channel. This allows for clear, high-quality audio output during playback. Constructed with exceptional materials, the JVC KW-M540BT is designed to ensure reliability and longevity. Overall, the JVC KW-M540BT is a versatile and user-friendly car radio that provides a range of convenient features. With its Bluetooth connectivity, USB port, and support for various radio bands, it offers an enjoyable and immersive audio experience for drivers and passengers alike.

General
BrandJVC
ModelKW-M540BT | KWM540BT
Productcar radio
EAN4975769449857
LanguageEnglish
FiletypeUser manual (PDF)
Ports & interfaces
BluetoothYes
Bluetooth version3.0+HS
Bluetooth profilesA2DP, AVRCP, PBAP
USB portYes
USB ports quantity1
USB port positionRear
ISO connectorYes
USB connector typeUSB Type-A
AV inputYes
AV outputYes
Line outputs (RCA)3
Microphone inYes
Performance
Product colorBlack
DIN size2 DIN
Maximum power per channel50 W
EqualizerYes
Equalizer bands quantity13
High pass filterYes
Low pass filterYes
DimmerYes
Output power- W
Audio output channels- channels
Ready for iPodYes
Disc types supportedNo
Analog signal format systemNTSC, PAL
Radio
Supported radio bandsFM, LW, MW
FM band range87.5 - 108 MHz
LW band range153 - 279 kHz
Radio Data System (RDS)Yes
Preset stations quantity24
Multimedia
MP3 playbackYes
Audio formats supportedAAC, FLAC, MP3, WAV, WMA
Image formats supportedBMP, JPEG, PNG
Video formats supportedAVI, H.264, MKV, MPEG1, MPEG2, MPEG4, WMV
USB direct playbackYes
CD-R playbackNo
Display
Rear-view camera readyYes
Built-in displayYes
Display diagonal6.8 "
WidescreenYes
TouchscreenYes
Display typeLCD
Display resolution800 x 480 pixels
LED backlightYes
Weight & dimensions
Width182 mm
Depth160 mm
Height111 mm
Weight1700 g
Packaging data
Package weight2800 g
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the JVC KW-M540BT below.

What is the weight of the JVC KW-M540BT?

The JVC KW-M540BT has a weight of 1700 g.

What is the difference between FM and AM?

FM stands for Frequency Modulation and AM stands for Amplitude Modulation. The biggest difference between FM radio stations compared to AM radio stations is the sound quality.

When is my volume too loud?

A volume above 80 decibels can be harmful to hearing. When the volume exceeds 120 decibels, direct damage can even occur. The chance of hearing damage depends on the listening frequency and duration.

My car radio does not turn on, now what?

If your car radio does not turn on, it will not receive any power. Check that the red wire is connected to the contact power supply and the yellow wire to the constant power supply.

How can I best clean my car radio?

A slightly damp cleaning cloth or soft, dust-free cloth works best to remove fingerprints. Dust in hard-to-reach places is best removed with compressed air.

What is bluetooth?

Bluetooth is a way of exchanging data wirelessly between electronic devices via radio waves. The distance between the two devices that exchange data can in most cases be no more than ten metres.

What is the screen size of the JVC KW-M540BT?

The screen size of the JVC KW-M540BT is 6.8 ".

What is the height of the JVC KW-M540BT?

The JVC KW-M540BT has a height of 111 mm.

What is the screen resolution of the display of the JVC KW-M540BT?

The screen resolution of the JVC KW-M540BT is 800 x 480 pixels.

What is the width of the JVC KW-M540BT?

The JVC KW-M540BT has a width of 182 mm.

What is the depth of the JVC KW-M540BT?

The JVC KW-M540BT has a depth of 160 mm.

What type of USB connection does the JVC KW-M540BT have?

The JVC KW-M540BT has a USB Type-A connection.

Does the JVC KW-M540BT have Bluetooth?

Yes, the JVC KW-M540BT has Bluetooth. This allows users to connect their smartphones or other devices wirelessly to the car radio for hands-free calling and audio streaming.

What is the Bluetooth version of the JVC KW-M540BT?

The Bluetooth version of the JVC KW-M540BT is 3.0+HS. While not the latest version, it still provides a reliable and stable connection for Bluetooth-enabled devices.

How many USB ports does the JVC KW-M540BT have?

The JVC KW-M540BT has 1 USB port located at the rear. This allows users to connect and charge their USB devices conveniently.

Does the JVC KW-M540BT support radio bands other than FM?

Yes, the JVC KW-M540BT supports not only FM radio but also LW (longwave) and MW (medium wave) radio bands. This allows users to tune into a wider range of radio stations.

Does the JVC KW-M540BT have a built-in equalizer?

Yes, the JVC KW-M540BT has a built-in equalizer with 13 bands. This allows users to customize the sound output according to their preferences, resulting in a better audio experience.

How do I pair the remote control with the JVC KW-M540BT car radio?

To pair the remote control with the JVC KW-M540BT car radio, follow these steps: 1. Press the "DIRECT" button on the remote control to select the search function. 2. Use the number keys on the remote control to enter the desired radio frequency you want to search for. 3. If you make a mistake, you can press the "CLR" button to clear the error. 4. Press the "/" button to confirm the entered frequency. 5. To exit the search mode, press the "DIRECT" button again. Please note that these steps are specific to the JVC KW-M540BT car radio and may vary for other models.

Why is the JVC Remote APP not connecting to my car radio?

The JVC Remote APP may not be connecting to your JVC KW-M540BT car radio due to various reasons. Here are some troubleshooting steps you can try: 1. Ensure that your smartphone has Bluetooth enabled and is within range of the car radio. 2. Make sure that the JVC Remote APP is installed and up to date on your smartphone. 3. Check that the car radio is in Bluetooth pairing mode. Refer to the car radio's manual for instructions on how to enable Bluetooth pairing. 4. On your smartphone, go to the Bluetooth settings and search for available devices. 5. Select the JVC KW-M540BT from the list of available devices. 6. If prompted, enter the PIN code displayed on the car radio's screen to complete the pairing process. 7. Once the pairing is successful, open the JVC Remote APP on your smartphone and follow the on-screen instructions to connect to the car radio. If the JVC Remote APP still does not connect, try restarting both your smartphone and the car radio, and repeat the pairing process.

What are the recommended installation and connection steps for the JVC KW-M540BT car radio?

To install and connect the JVC KW-M540BT car radio, follow these recommended steps: 1. Connect the wiring of the supplied wire harness as shown in the diagram. Make sure to connect the antenna to the antenna connection. 2. Connect the ISO plugs to the corresponding connectors on the car radio. 3. Use the provided screws to securely install the car radio into the dashboard. 4. If you are using an optional rearview camera, connect it to the designated input on the car radio. 5. Connect any external components, such as a microphone or audio/video input, to their respective inputs on the car radio. 6. If you are connecting an external amplifier, make sure to connect the ground wire to the car chassis to prevent damage to the car radio. 7. Install the car radio with the mounting sleeve by bending the tabs and securing it in place. 8. Attach the decorative plate to the car radio. 9. To remove the car radio, remove the decorative plate and use the removal keys to pull out the unit. Please note that these steps are specific to the JVC KW-M540BT car radio and may vary for other models.

Why is there no sound coming from the car radio after installation?

There could be several reasons why there is no sound coming from the JVC KW-M540BT car radio after installation. Here are some possible troubleshooting steps: 1. Check the volume level of the car radio and make sure it is not set to mute. Adjust the volume to an audible level. 2. Verify that the speakers are properly connected to the car radio. Ensure that the speaker wires are securely connected to the corresponding terminals on the car radio. 3. Check the balance and fader settings of the car radio. Make sure that the sound is not being directed to a specific speaker or channel. 4. Ensure that the audio source (e.g., radio, CD, USB) is selected and playing properly. Try switching to a different audio source to see if the issue persists. 5. Check the audio settings of the car radio. Make sure that the equalizer settings, bass, treble, and other audio enhancements are properly adjusted. 6. If you have installed an external amplifier, check the connections and settings of the amplifier. Ensure that the amplifier is receiving power and properly connected to the car radio. 7. If none of the above steps resolve the issue, it is recommended to consult a professional car audio technician for further assistance. Please note that these troubleshooting steps are general guidelines and may vary depending on the specific installation and configuration of the car radio.

How can I prevent the cables and wires from getting damaged by hot metal parts in my car?

To prevent cables and wires from getting damaged by hot metal parts in your car, follow these steps: 1. Identify the hot metal parts in your car, such as the engine, exhaust system, or any other components that generate heat during operation. 2. Route the cables and wires away from these hot metal parts. Ensure that they are not in direct contact or close proximity to the hot surfaces. 3. Use cable clips or ties to secure the cables and wires in place and prevent them from coming into contact with the hot metal parts. 4. If necessary, use heat-resistant sleeves or tubing to cover the cables and wires that are in close proximity to the hot metal parts. This will provide an additional layer of protection against heat. 5. Regularly inspect the cables and wires for any signs of damage or wear. If you notice any frayed or exposed wires, replace them immediately to prevent potential hazards. 6. Avoid running cables and wires through areas with sharp edges or moving parts that could cause abrasion or damage. 7. If you are unsure about the proper routing or protection of the cables and wires, consult a professional car audio technician for guidance. By following these steps, you can help ensure the safety and longevity of your car radio's cables and wires.

How do I troubleshoot the remote control of the JVC KW-M540BT car radio?

To troubleshoot the remote control of the JVC KW-M540BT car radio, follow these steps: 1. Ensure that the remote control has fresh batteries. If the batteries are low or depleted, replace them with new ones. 2. Check the line of sight between the remote control and the car radio. Make sure there are no obstructions blocking the signal. Stand within a reasonable range and aim the remote control directly at the car radio. 3. Clean the remote control's infrared transmitter and the car radio's infrared receiver. Use a soft, lint-free cloth to remove any dust or dirt that may be interfering with the signal transmission. 4. Reset the remote control and the car radio. Remove the batteries from the remote control and disconnect the car radio from its power source for a few minutes. Then, reinsert the batteries and reconnect the car radio to its power source. 5. If the issue persists, try using the remote control from a different location or angle. Sometimes, changing the position can improve the signal reception. If none of these steps resolve the issue, it is recommended to contact JVC customer support for further assistance.

What should I do if the JVC Remote APP is not connecting to the car radio?

To troubleshoot the issue of the JVC Remote APP not connecting to the JVC KW-M540BT car radio, follow these steps: 1. Ensure that the JVC Remote APP is installed on your smartphone. You can download it from the official app store. 2. Make sure that Bluetooth is enabled on both your smartphone and the car radio. Check the Bluetooth settings on your smartphone and ensure that it is discoverable. 3. On the car radio, navigate to the Bluetooth settings menu. Select the option to pair a new device or search for available devices. 4. Open the JVC Remote APP on your smartphone and follow the on-screen instructions to connect to the car radio. Make sure to select the correct car radio model from the list of available devices. 5. If the connection fails, try restarting both your smartphone and the car radio. Turn off Bluetooth on both devices, wait for a few seconds, and then turn it back on. 6. If the issue persists, check for any firmware updates for the car radio. Visit the JVC website or contact JVC customer support for information on how to update the firmware. By following these steps, you should be able to troubleshoot the issue of the JVC Remote APP not connecting to the JVC KW-M540BT car radio.

What troubleshooting steps should I follow if I encounter issues during the installation and connection of the JVC KW-M540BT car radio?

To troubleshoot issues during the installation and connection of the JVC KW-M540BT car radio, follow these steps: 1. Verify that the wiring connections are correct. Ensure that the wires from the car's wiring harness are properly connected to the corresponding wires on the car radio. Refer to the wiring diagram in the manual for guidance. 2. Check the fuse. Make sure the fuse for the car radio is not blown. If it is, replace it with a fuse of the same rating. 3. Confirm that the antenna is properly connected. Ensure that the antenna cable is securely connected to the antenna input on the car radio. 4. Check the power connections. Verify that the red wire (ACC wire) is connected to a switched power source and the yellow wire (battery wire) is connected to a constant power source. Make sure the ground wire is securely connected to a metal part of the car's chassis. 5. If you are using external components such as a microphone or rearview camera, ensure that they are properly connected to the corresponding inputs on the car radio. By following these troubleshooting steps, you should be able to resolve any installation and connection issues with the JVC KW-M540BT car radio.

How can I troubleshoot if the JVC KW-M540BT car radio is not functioning properly after installation?

To troubleshoot if the JVC KW-M540BT car radio is not functioning properly after installation, follow these steps: 1. Check the wiring connections. Ensure that all the wires are properly connected according to the wiring diagram in the manual. Make sure there are no loose or disconnected wires. 2. Verify the power source. Ensure that the car radio is receiving power from the correct source. Check the connections of the red (ACC) and yellow (battery) wires to ensure they are properly connected to the appropriate power sources. 3. Confirm the ground connection. Ensure that the ground wire is securely connected to a metal part of the car's chassis. A poor ground connection can cause issues with the car radio's functionality. 4. Reset the car radio. Disconnect the car radio from its power source for a few minutes, then reconnect it. This can help reset the system and resolve any temporary issues. 5. Check for firmware updates. Visit the JVC website to see if there are any available firmware updates for the car radio. Updating the firmware can address any software-related issues. If the car radio continues to have problems after following these troubleshooting steps, it is recommended to contact JVC customer support for further assistance.

What should I do if the cables and wires of the JVC KW-M540BT car radio are in contact with metal parts that emit heat?

If the cables and wires of the JVC KW-M540BT car radio are in contact with metal parts that emit heat, follow these steps: 1. Identify the metal parts that are emitting heat. These can include components such as the car's engine, exhaust system, or other hot surfaces. 2. Carefully inspect the cables and wires connected to the car radio. Look for any areas where they are in direct contact with the hot metal parts. 3. Gently reposition the cables and wires to ensure they are not touching the hot metal surfaces. Use cable ties or clips to secure the cables and keep them away from the heat-emitting parts. 4. If necessary, use heat-resistant insulation materials to provide additional protection for the cables. Wrap the cables with heat-resistant tape or sleeve to prevent direct contact with the hot metal surfaces. 5. Test the car radio to ensure it is functioning properly after repositioning the cables and providing insulation. Check for any abnormal behavior or malfunctions. By following these steps, you can prevent potential damage to the cables and wires of the JVC KW-M540BT car radio caused by contact with metal parts that emit heat.

Is the manual of the JVC KW-M540BT available in English?

Yes, the manual of the JVC KW-M540BT is available in English .

Is your question not listed? Ask your question here

No results