Junker JD66SE50 manual

Junker JD66SE50
7.9 · 1
PDF manual
 · 40 pages
English
manualJunker JD66SE50
19

Connecting the pipes

Note: If using an aluminium pipe, smooth the connection area
beforehand.
Exhaust-air pipe Ø 150 mm (recommended size)
Attach the exhaust-air pipe directly to the air-pipe connector
and seal.
Exhaust-air pipe Ø 120 mm
1. Attach the reducing connector directly to the air-pipe
connector.
2. Attach the exhaust air pipe to the reducing connector.
3. Seal both joints appropriately.

Electrical connection

: Risk of electric shock!

from damaged connection cable. Do not kink or pinch
connection cable during installation.
The required connection data can be found on the rating plate
inside the appliance; to do this, remove the metal mesh grease
filter.
Length of the cable: approx. 1.30 m
This appliance complies with the EC interference suppression
regulations.
This appliance may be connected to a correctly installed
earthed socket only.
Attach the earthed socket preferably inside the flue duct.
The earthed socket should be connected via its own circuit.
If the earthed socket is no longer accessible following
installation of the appliance, a disconnecter must be fitted as
for a permanent connection.
If a permanent connection is required, the installation must
feature an all-pole disconnecter (circuit breakers, fuses and
contactors) with a min. 3 mm contact opening. The permanent
connection may be installed by an electrician only.

Attaching the flue duct

: Risk of injury!

From sharp edges during installation. Always wear protective
gloves while installing the appliance.
1. Separate the flue ducts.
To do this, remove the adhesive tape.
2. Remove the protective foil from both flue ducts.
3. Push one flue duct into the other.
Notes
To prevent scratches, place paper for protection over
the edges of the outer flue duct.
Slots of the inner flue duct downwards.
4. Place flue ducts on the appliance.
5. Push inner flue duct upwards and attach to the fixing
brackets on the left and right.
¨
6. Press flue duct downwards until it engages. ©
7. Screw flue duct to the sides of the fixing bracket using two
screws.
ª
PLQ
PP
PLQ
PP
PLQPP
PD[PP
$
%

&

Manual

View the manual for the Junker JD66SE50 here, for free. This manual comes under the category exhaust hoods and has been rated by 1 people with an average of a 7.9. This manual is available in the following languages: English. Do you have a question about the Junker JD66SE50 or do you need help? Ask your question here

Index

Need help?

Do you have a question about the Junker and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Junker JD66SE50 specifications

Below you will find the product specifications and the manual specifications of the Junker JD66SE50.

General
BrandJunker
ModelJD66SE50
Productexhaust hood
LanguageEnglish
FiletypeUser manual (PDF)

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Junker JD66SE50 below.

When should I replace the carbon filter on my extractor hood?

The carbon filter should be replaced every three to twelve months.

How often should I clean the metal hood grease filters?

The metal grease filters should be cleaned every eight to ten weeks.

Where can I find the model number of my cooker ectractor hood?

The model number of the hood is usually found on a white label inside the hood.

Is the manual of the Junker JD66SE50 available in English?

Yes, the manual of the Junker JD66SE50 is available in English .

Is your question not listed? Ask your question here

No results