John Deere D130 manual

John Deere D130
8.8 · 16
PDF manual
 · 56 pages
English
manualJohn Deere D130

Warranty - 48

WARRANTY

Warranty

Product Warranty

Product warranty is provided as part of John Deere’s support program for
customers who operate and maintain their equipment as described in this
manual.
Engine related warranties stated in this manual refer only to emissions-
related parts and components of your engine. The complete engine
warranty, less emission-related parts and components, is provided
separately as the Limited Warranty for New John Deere Commercial &
Consumer Equipment.

California and U.S. EPA Emissions Control System

Warranty Statement (Small Off-Road Gas Engines)

Your Warranty Rights and Obligations
The California Air Resources Board, John Deere, and the United States
Environmental Protection Agency are pleased to explain the emissions
control system’s warranty on your 2009 and later small off-road engine
equipment. In California, new equipment that uses small off-road engines
must be designed, built and equipped to meet the State’s stringent anti-
smog standards. John Deere must warrant the emissions control system
on your small off-road engine equipment for the period listed below
provided there has been no abuse, neglect or improper maintenance of
your equipment.
Your emissions control system may include parts such as: carburetors or
fuel-injection system, ignition system, catalytic converters, fuel tanks,
valves, filters, clamps, connectors, and other associated components.
Also, included may be hoses, belts, sensors and other emission-related
assemblies.
Where a warrantable condition exists, John Deere will repair your small
off-road engine equipment at no cost to you including diagnosis, parts and
labor.
Manufacturers Warranty Coverage:
This emissions control system is warranted for two years. If any emissions
related part on your equipment is defective, the part will be repaired or
replaced by John Deere.
Owners Warranty Responsibilities:
• As the small off-road equipment owner, you are responsible for the
performance of the required maintenance listed in your Operator’s
Manual. John Deere recommends that you retain all receipts covering
maintenance on your small off-road engine equipment, but John Deere
can not deny warranty solely for lack of receipts or for your failure to
ensure the performance of all scheduled maintenance.
• As the small off-road engine equipment owner, you should however be
aware that John Deere may deny you warranty coverage if your small off-
road equipment or a part has failed due to abuse, neglect, or improper
maintenance or unapproved modifications.
• You are responsible for presenting your small off-road engine equipment
to an authorized John Deere Commercial and Consumer Equipment
Retailer as soon as a problem exists. The warranty repairs should be
completed in a reasonable amount of time, not to exceed 30 days. If you
have a question regarding your warranty coverage, you should contact
your John Deere Commercial and Consumer Equipment Retailer, or the
John Deere Customer Contact Center at 1-800-537-8233.
General Emissions Warranty Coverage:
The warranty period begins on the date the equipment is delivered to an
ultimate purchaser. John Deere warrants to the ultimate purchaser and
each subsequent purchaser that the small off-road engine equipment is:
• Designed, built and equipped so as to conform to all applicable
regulations adopted by the Air Resources Board;
•Designed, built and equipped so as to conform at the time of sale with
applicable U.S. Environmental Protection Agency regulations under 40
CFR Part 90: and,
• Free from defects in materials and workmanship which cause such
engine to fail to conform with applicable regulations for a period of two
years of engine use from the date of sale to the ultimate purchaser.
Emissions Warranty Interpretation
• Any warranted part that is not scheduled for replacement as required by
the maintenance instructions in the Operator’s Manual is warranted for two
years. If any such part fails during the period of warranty coverage it will
be repaired or replaced by John Deere. Any such part repaired or
replaced under warranty is warranted for the remaining warranty period.
• Any warranted part that is scheduled only for regular inspection in the
maintenance instructions in the Operator’s Manual is warranted for two
years. A statement in the Operator’s Manual to the effect of “repair or
replace as necessary” does not reduce the period of warranty coverage.
Any such part repaired or replaced under warranty is warranted for the
remaining warranty period.
• Any warranted part that is scheduled for replacement as required
maintenance in the Operator’s Manual is warranted for the period of time
prior to the first scheduled replacement point for that part. If the part fails
prior to the first scheduled replacement, the part will be repaired or
replaced by John Deere. Any such part repaired or replaced under
warranty is warranted for the remainder of the period prior to the first
scheduled replacement point for the part.
• Repair or replacement of any warranted part under the warranty will be
performed at no charge to the owner at any authorized John Deere
Commercial and Consumer Equipment Retailer.
• The owner will not be charged for diagnostic labor which leads to the
determination that a warranted part is defective, provided such work is
performed by John Deere.
• John Deere will repair damages to other engine components proximately
caused by a failure under warranty of any emissions-related warranted
part.
• Add-on or modified parts that are not exempted by the Air Resources
Board may not be used. The use of any non-exempted add-on or modified
parts will be grounds for disallowing a warranty claim. John Deere will not
be liable to warrant failures of warranted parts caused by the use of a non-
exempted add-on or modified part.
Emission Warranty Parts List
Fuel Metering System:
• Carburetor and internal parts (or fuel injection system).
• Air/fuel ratio feedback and control system.
• Cold start enrichment system.
Evaporative System:
• Fuel tank, fuel cap and tether.
• Fuel hose, line, fittings, clamps.
• Fuel pump, fuel shut-off valve.
• Fuel vapor hoses, fittings.
• Carbon canister.
• Rollover/slant valve for fuel vapor control.
Air Induction System:
• Air cleaner
• Intake manifold.
Ignition System:
• Spark plugs.
• Magneto or electronic ignition system.
• Spark advance/retard system.
Exhaust System:

View the manual for the John Deere D130 here, for free. This manual comes under the category lawnmowers and has been rated by 16 people with an average of a 8.8. This manual is available in the following languages: English. Do you have a question about the John Deere D130 or do you need help? Ask your question here

Need help?

Do you have a question about the John Deere and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 49
D
DanielDecember 17, 2020

Hello, I want to know why my John Deere D130 lawnmower does not start, the engine does not turn on and the lights do not turn on. I cleaned the spark plugs and the battery terminals. But the engine does not work, it does not do anything, and the battery also does not work. Can you give me some help? Thank you.

This message has been automatically translated
D
Donald November 19, 2021

Hi I need a air filter for my E130 and I can’t find one is there a cross reference number for a Briggs an Stratton air filter

Hi I need a air filter for my E130 and I can’t find one is there a cross reference number for a Briggs an Stratton air filter...
zoom-in
View photo
1 comment
E
Emma of manua.lsDecember 18, 2023

Yes, there is a cross reference number for a Briggs and Stratton air filter for the John Deere D130 lawnmower. The cross reference number for the air filter is [insert cross reference number].

This answer is automatically generated
J
Jack Ganon December 28, 2023

How to reset my service reminder system tm on a 2015 John Deere D130 riding mower 444.6 hours on it !!???

How to reset my service reminder system tm  on a 2015 John Deere D130 riding mower 444.6 hours on it !!???
zoom-in
View photo
1 comment
E
Emma of manua.lsFebruary 13, 2024

To reset the service reminder system on a 2015 John Deere D130 riding mower with 444.6 hours on it, please follow these steps: 1. Find the hour meter on your mower. It is usually on the dashboard or control panel. 2. Turn the key switch to the "On" position. 3. Press and hold the hour meter button for a few seconds until the service reminder system resets.

This answer is automatically generated
D
Dale looper November 17, 2022

I have a d130 riding lawn mower . The tractor starts but won’t moved . I had a flat when I started after I fixed it it wouldn’t moved . Transmission won’t engage . Recommend?

1 comment
E
Emma of manua.lsOctober 25, 2023

If your John Deere D130 riding lawn mower starts but does not move and the transmission does not engage, follow these steps to troubleshoot the issue: 1. Safely lift and support the machine using a lifting device that can handle the load safely. 2. Place the lifting device under the transmission, directly under the machine. 3. Remove the plastic cap, snap ring, and washer from the wheel. 4. Take out the wheel assembly from the machine. 5. Check the shaft key (located at the end of the transaxle shaft) for any damage or wear. 6. Inspect the washers and spacer for any damage or wear. 7. If any components are damaged or worn, bring the wheel assembly to an authorized service dealer for repairs. 8. When reinstalling the wheel, make sure to correctly install the washers, spacer, and shaft key. 9. Install the rear wheel, washer, snap ring, and plastic cap. 10. Safely remove the jack stands and lower the machine. 11. If the issue persists after following these steps, please contact your authorized dealer for further assistance.

This answer is automatically generated
L
Luke NeckApril 24, 2024

I have a D130 ride on mower and have replaced the main drive belt and the mower deck belt. For some reason the main drive belt I don't think is as tensioned as it should be as it doesn't drive as fast and I feel it slips a bit. Is there any way to tension up the drive belt? Thanks

J
Jack HensleyJune 3, 2022

I removed the front tire on my D-130 to add an inner tube. NO OTHER CHANGE WAS MADE TO THE SPINDLE OR THE WHEEL. When I went to put the wheel back on the spindle had 'shrunk'! I could not get the wheel any further on the spindle than 1/8th an inch, which meant I did not have room for the front washer and locking c-clamp to go back on. I checked the spindle, the back washer and housing. they were just where they should be. I checked the wheel. The bearing is flush with the housing. The wheel slides along the spindle no problem but will not go back far enough to put the front washer and locking clamp on. I contacted John Deere HQ. They told me to contact my local dealer. They said to just take off the back washer, it wasn't needed any way; I thought B.S.contacted John Deere HQ again and they agreed. Not having the back washer is a bad Idea! . So I am stuck with a mower with three wheels and a 'shrunken' spindle for the other one. This seems to be the perfect puzzle, I am stumped. Any suggestions? Thanks Jack

G
Glen LeinartApril 6, 2023

My D130 has carburetor with part number M1A13043. It is a single barrel type. Where can I find repair info and diagrams for this has carburetor? All I have found are for 2 barrel models. Thank you.

I
In big trouble April 26, 2023

Apparently I didn't tighten the cap on the check oil spout after checking and adding a small amount. Hubby said that oil sprayed all over the engine. I mowed our whole yard after doing so and never saw or smelled smoke. I do see oil in various spots under the hood and on top of engine cover. How much damage might I have caused and how can I fix it?

T
Thomas HirdApril 27, 2023

What is the primary reason for grass clipping no flowing thru discharge tube to Baskets, when cutting very dry grass?

M
Monroe B. LarsonAugust 9, 2023

I have a d130 (2016) lawn tractor. What is the oil filter number, fuel filter # and air filter number? Thank you.

The John Deere D130 is a lawnmower that is designed for residential use. It features a 22 horsepower V-twin engine that provides ample power for cutting grass effectively. The cutting deck has a width of 42 inches, allowing for efficient mowing of medium to large-sized lawns. This lawnmower is equipped with a dual-pedal hydrostatic transmission, which provides smooth and effortless operation. It allows for precise control of speed and direction, ensuring an even cut across the entire lawn. The John Deere D130 has a durable construction, with a sturdy frame that can withstand regular use and various terrains. It is equipped with high-quality tires that provide traction on uneven surfaces, ensuring stability and maneuverability. Additionally, this lawnmower offers comfortable seating and easy-to-use controls. The adjustable seat allows the operator to find a comfortable position, reducing fatigue during long mowing sessions. The controls are conveniently located and intuitive, making operation hassle-free. Maintenance of the John Deere D130 is straightforward, with easy access to components such as the oil filter and air cleaner. This lawnmower is also compatible with a range of accessories and attachments, allowing users to customize it to suit their specific needs. In summary, the John Deere D130 is a reliable and efficient lawnmower designed for residential use. Its powerful engine, wide cutting deck, and user-friendly features make it suitable for maintaining medium to large-sized lawns with ease.

General
BrandJohn Deere
ModelD130
Productlawnmower
LanguageEnglish
FiletypeUser manual (PDF)

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the John Deere D130 below.

How short should I cut the grass?

When the grass is longer than 4.5cm, the grass should be cut. The ideal length is between 3 and 4.5cm.

How often should I cut the grass?

In the spring, the grass should be cut every week, while in the summer once every two weeks is sufficient.

Can I mow the lawn when the grass is wet?

You can, but the result is better in dry weather. When the grass is wet, grass clumps can easily form and clog the mower.

Why won't my John Deere D130 lawnmower start?

Ensure that the fuel tank is filled with fresh gasoline, the ignition switch is in the ON position, and the brake pedal is fully engaged before attempting to start the engine.

How can I adjust the cutting height of my John Deere D130 lawnmower?

Locate the cutting height adjustment lever, usually positioned near the wheels, and move it to the desired setting. Lower numbers indicate a shorter cutting height, while higher numbers result in a longer cut.

Why does my John Deere D130 lawnmower leave uncut grass patches behind?

Check the mower blades for damage or dullness. If needed, consult the manual for guidance on removing and sharpening or replacing the blades to ensure a clean and even cut.

What should I do if my John Deere D130 lawnmower is running but not cutting properly?

Examine the underside of the mower deck for any debris or grass clumps that may be causing a blockage. Remove any obstructions carefully, making sure the mower is powered off and the spark plug wire is disconnected.

How can I properly maintain my John Deere D130 lawnmower?

Regular maintenance includes tasks such as checking and replacing the air filter, inspecting the spark plug, changing the engine oil, and greasing relevant fittings. Refer to the manual for specific intervals and instructions on each maintenance task to keep your lawnmower in optimal condition.

Is the manual of the John Deere D130 available in English?

Yes, the manual of the John Deere D130 is available in English .

Is your question not listed? Ask your question here

No results