JETI MUI50 EX manual

JETI MUI50 EX
8.9 · 2
PDF manual
 · 4 pages
English
manualJETI MUI50 EX

Sensor MUI EX

-2-
MUI MENU: MIN / MAX by pushing the button D (downward arrow) you will select the display of

extreme voltage and current value recordings which occurred during the measurement. The extreme

recordings are deleted automatically or they can be deleted in the menu Setting - Erase Data. Automatic

deletion occurs when the MUI sensor has just been connected to the voltage supply and the current, as set

in the menu Setting-Start Trigger, will be exceeded. If after connection of the sensor the set current will

not be exceeded, values of the previous sensor operation will be displayed.

U MIN / MAX shows the minimum and maximum value of the measured voltage
I AVG / MAX shows the average value of the measured current and its maximum
MUI MENU: Setting by pushing the button D (downward arrow) you will enter the basic sensor setup

menu

Start Trigger setup of a current value, at which after sensor connection recording of values like

minimum, maximum and current transit time starts. If the adjusted value is 0 A, values will be recorded

immediately after connection of the sensor to its power supply and data read out of the previous operation

will not be possible.

Erase Data by pushing arrows R and L (right and left) simultaneously the records of measured

parameters will be deleted

First Parametr adjustment of the display of the first parameter in the JETIBOX LCD, which is shown

in the second line of the basic sensor menu (the first line shows the identification, for instance SENSOR

MUI 30)

Second Parametr - adjustment of the display of the second parameter in the JETIBOX LCD, which is

shown in the second line of the basic sensor menu (the first line shows the identification, for instance

SENSOR MUI 30)

Auto. Erase - This function of automatical deletion after overstepping the trigger level can be activated or

deactivated.

MUI MENU: ALARMS by pushing button D (downward arrow) you enter setup of particular alarms.

If one of the adjusted parameters becomes exceeded, the JETIBOX LCD will in the second line of the

basic menu alternately show the original display with the pertinent alarm and the transmitter module siren

will emit an acoustical alarm. The first tone is a revelation signal and the second one is signalling a Morse

Code character of the relevant alarm. If the alarm is set to OFF, this kind of alarm will be switched off.

Voltage alarm (alarm U ..- ) adjustment of the value of voltage signalling, if the measured voltage

decreases beyond the set value, the voltage alarm U will be activated.

Current alarm (alarm I .. ) adjustment of the value of current signalling, if the measured current

increases beyond the set value, the current alarm I will be activated.

Capacity alarm (alarm C -.-. ) adjustment of the signalling value of consumed capacity , if the

adjusted value of maximum consumed capacity is exceeded, alarm C will be activated.

MUI MENU: SERVICE by pressing button D (arrow down) you will change to depiction of the

firmware version and to renewal of the sensor default setting.

Factory Defaults by simultaneous pressing of arrows R and L (right and left) the factory settings of the

MUI are loaded.

MUI v. xx.xx ID xxxxx:xxxxx product marking with firmware version and series number (ID).

Particular phases of current measurements

A when after switching on of the sensor the

current did not exceed the set value Start Trigger.

Measured values (U MIN / MAX, I AVG / MAX,

Capacity, Run Time) correspond with measured

values of the previous operation.

B the value Start Trigger has been exceeded.

Previous measured values (U MIN / MAX, I AVG /

MAX, Capacity, Run Time) will be deleted and

actualized by the actual measurement course.

Manual

View the manual for the JETI MUI50 EX here, for free. This manual comes under the category radio controlled toys and has been rated by 2 people with an average of a 8.9. This manual is available in the following languages: English. Do you have a question about the JETI MUI50 EX or do you need help? Ask your question here

Need help?

Do you have a question about the JETI and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

JETI MUI50 EX specifications

Below you will find the product specifications and the manual specifications of the JETI MUI50 EX.

General
BrandJETI
ModelMUI50 EX | JEX-MUI-50
Productradio controlled toy
EAN8595245909703
LanguageEnglish
FiletypeUser manual (PDF)
Weight & dimensions
Width19 mm
Height11 mm
Length (max)27 mm
Weight19 g
Power
Maximum current50 A
Voltage5 - 8.4 V
Packaging data
Quantity per pack1 pc(s)
Operational conditions
Operating temperature (T-T)-10 - 85 °C
Features
TypeRadio-Controlled (RC) Model Parts
Product colorMulticolor
Product typeTelemetry sensor
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the JETI MUI50 EX below.

What is the weight of the JETI MUI50 EX?

The JETI MUI50 EX has a weight of 19 g.

A battery in my radio controlled toy has started to corrode. Is the device still safe to use?

The product can still be used safely after proper cleaning. Remove the battery with gloves and clean the battery compartment with a toothbrush and vinegar. After drying, new batteries can be inserted into the device.

What is the height of the JETI MUI50 EX?

The JETI MUI50 EX has a height of 11 mm.

What is the width of the JETI MUI50 EX?

The JETI MUI50 EX has a width of 19 mm.

Is the manual of the JETI MUI50 EX available in English?

Yes, the manual of the JETI MUI50 EX is available in English .

Is your question not listed? Ask your question here

No results