JETI Hicopter 90A opto manual

JETI Hicopter 90A opto
8.7 · 1
PDF manual
 · 1 page
English
manualJETI Hicopter 90A opto

HiCOPTER

The HiCOPTER product line of speed controllers are designed for controlling and regulating
brushless motors that are typically used for powering multicopters. Each speed controller is pre-set
from the factory with settings optimized for use with multi rotor aircraft stabilization systems.
HiCOPTER controllers accept a control signal with a frequency of up to 500Hz. This allows them to
accurately respond to any RPM change required by the control/stabilization unit of the multicopter.
The motor control signal is galvanically (optically) separated from the flight battery in all
HiCOPTER speed controllers. HiCOPTER speed controllers do not require or allow any programming
changes. The propeller brakes are already switched off, the cut-off voltage is pre-set to the lowest
possible level (depending on type) and the motor timing is set automatically by the speed controller. If
you need to change the direction of rotation, simply swap any two of the motor wires.
Install the HiCOPTER speed controller in accordance with the manual instructions for your specific
multicopter type.
Basic parameters of HiCOPTER speed controllers
Type
Current
[A]
Input voltage
[V]
Dimensions
[mm]
Weight*
[g]
HiCOPTER 30A opto 30 5-25,2 65x26x9 35
HiCOPTER 40A opto 40 5-25,2 65x26x9 38
HiCOPTER 70A opto 70 5-25,2 70x26x11 45
HiCOPTER 90A opto 90 12-42 65x55x17 100
* weight with the cables
General Principles:
please read these instructions carefully
use only new connectors of good quality, which must be soldered properly to the controller
cables (look out for and remove any remaining flux on the plugs)
flight battery wires can be extended to a maximum overall length of 20 cm
pay attention to the distance between all cables and the receiver antenna the two should be
kept as far apart as possible
only connect the flight batteries to the flight system shortly before the flight and then
disconnect them immediately after landing
when the model is not in use, always disconnect all batteries from the flight system
to prevent the possibility of reverse polarity connections to the controller or batteries use
different types of connectors for each type of connection
do not connect the controller to current supplies other than appropriate battery pack (verify
that your batteries are the correct input voltage and can handle the current load)
to prevent possible injuries by moving mechanical parts of the model (motor, gear box etc.)
always keep in mind that the motor may start unintentionally
check the controller and receiver circuitry each time before switching the system on
install the controllers in the model so that they receive air flow for cooling
Warranty:
We grant a warranty of 24 months from the date of purchase under the premise that the item has
been operated in accordance with these instructions within the specified voltage and currents and that
the controller does not show signs of mechanical damage. The warranty is void if the polarity of the
controller has been reversed or if the controller came in contact with different chemicals or water.
A controller can also be damaged due to following reasons: Use of unsuitable connectors, low
quality soldering joints (plugs), overly long cables between battery controller motor, a
demagnetizated motor, phase interruption (broken or damaged wire) between motor and controller
during operation.
Warranty service and any post warranty service is provided by the distributor or manufacturer.
JETI model s.r.o., Lomená 1530, 742 58 Příbor, Czech Republic www.jetimodel.cz

Manual

View the manual for the JETI Hicopter 90A opto here, for free. This manual comes under the category radio controlled toys and has been rated by 1 people with an average of a 8.7. This manual is available in the following languages: English. Do you have a question about the JETI Hicopter 90A opto or do you need help? Ask your question here

Index

Need help?

Do you have a question about the JETI and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

JETI Hicopter 90A opto specifications

Below you will find the product specifications and the manual specifications of the JETI Hicopter 90A opto.

General
BrandJETI
ModelHicopter 90A opto | J-HIC-90-O
Productradio controlled toy
EAN8595245900625
LanguageEnglish
FiletypeUser manual (PDF)
Weight & dimensions
Width65 mm
Depth55 mm
Height17 mm
Weight100 g
Power
Maximum current90 A
Voltage12 - 42 V
Packaging data
Quantity per pack1 pc(s)
Operational conditions
Operating temperature (T-T)-20 - 85 °C
Battery
Compatible battery maximum number of cells10
Compatible battery technologiesLithium Polymer (LiPo)
Compatible battery minimum number of cells4
Features
TypeRadio-Controlled (RC) Model Parts
Brand compatibilityAny brand
Product colorYellow
Proper useMulticopter
Product typeSpeed controller
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the JETI Hicopter 90A opto below.

What is the weight of the JETI Hicopter 90A opto?

The JETI Hicopter 90A opto has a weight of 100 g.

A battery in my radio controlled toy has started to corrode. Is the device still safe to use?

The product can still be used safely after proper cleaning. Remove the battery with gloves and clean the battery compartment with a toothbrush and vinegar. After drying, new batteries can be inserted into the device.

What is the height of the JETI Hicopter 90A opto?

The JETI Hicopter 90A opto has a height of 17 mm.

What is the width of the JETI Hicopter 90A opto?

The JETI Hicopter 90A opto has a width of 65 mm.

What is the depth of the JETI Hicopter 90A opto?

The JETI Hicopter 90A opto has a depth of 55 mm.

Is the manual of the JETI Hicopter 90A opto available in English?

Yes, the manual of the JETI Hicopter 90A opto is available in English .

Is your question not listed? Ask your question here

No results