Husqvarna Z 448 manual

Husqvarna Z 448
7.5 · 1
PDF manual
 · 244 pages
English
manualHusqvarna Z 448

V-belts

Check the belts every 100 hours of operation.
Check for severe cracking and large nicks.
The belt will show some small cracks in normal
operation. The belts are not adjustable. Replace
the belts if they begin to slip from wear.
Deck Belt Removal
1. Park on a level surface and apply the parking
brake. Lower the deck to the lowest cutting
position.
2. Remove all belt shielding.
3. Remove the debris that has accumulated
around the cutter housings and the deck
surface.
4. Push inward on the idler arm to release the
tension on the belt.
5. Slip the belt over the top of the cutter housing
pulleys and remove the belt from the deck.
Deck Belt Installation
NOTE: For ease in installing the deck belt, refer to
the routing decal on the top of the deck.
1. Wrap the deck belt around the electric clutch
pulley located on the engine shaft.
2. Route the belt forward and up onto the deck.
3. Place the belt around the idler pulley.
4. Wrap the belt around the stationary idler
pulley and around the mandrel housings.
5. Push inward on the idler arm and carefully
route the belt over the stationary idler pulley.
Once the belt is properly routed, slowly
release the idler arm to tension the belt.
6. Make sure the belt routing matches the deck
decal and that the belt does not have any
twists.
7. Reinstall all belt shielding.

Safety System

The machine has a safety system that prevents
starting or driving under the following conditions.
The engine can only be started when:
the mower deck is disengaged.
the steering controls are in the outer, locked
neutral / parking brake position.
IMPORTANT INFORMATION To be able to
drive, the driver must be seated and move
both steering levers in toward each other at the
same time, otherwise the engine will stop.
Make daily inspections to ensure that the safety
system works by attempting to start the engine
when one of the conditions is not met. Change
the conditions and try again.
If the machine starts when one of these
conditions is not met, turn the machine o and
repair the safety system before using the machine
again.
Make sure the engine stops when the park brake
is released and the operator leaves the seated
position.
Check that the engine stops if the mower blades
are engaged and the driver temporarily moves o
the driver’s seat.

Park Brake and Steering

Visually check that no damage is found on the
lever, links, or switches belonging to the park
brake. Do a standstill test and check that there
is sucient braking. For park brake adjustments,
contact the Husqvarna service workshop.
WARNING! Faulty adjustment will result
in reduced braking and can cause an accident.

Tire Pressures

All tires must be at 15 psi / 103 kPa / 1 bar.
IMPORTANT INFORMATION DO NOT add
a tire liner or foam ll material to the tires.
Excessive loads created by foam lled tires will
cause premature failures.
Only use tires specied by Husqvarna.
24

MAINTENANCE

View the manual for the Husqvarna Z 448 here, for free. This manual comes under the category lawnmowers and has been rated by 1 people with an average of a 7.5. This manual is available in the following languages: English. Do you have a question about the Husqvarna Z 448 or do you need help? Ask your question here

Need help?

Do you have a question about the Husqvarna and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

The Husqvarna Z 448 is a lawnmower designed for residential use. It features a 48-inch cutting deck made of durable materials for long-lasting performance. The lawnmower is powered by a reliable engine that provides sufficient power for cutting grass effectively. With a hydrostatic transmission, the Husqvarna Z 448 offers smooth and effortless operation, allowing users to easily maneuver around obstacles in the yard. The lawnmower is equipped with comfortable seating and ergonomic controls for user convenience. It also has adjustable cutting heights to accommodate different grass lengths. The Husqvarna Z 448 is designed to provide a clean and precise cut, leaving the lawn looking well-maintained. Additionally, it has a compact design for easy storage when not in use. Overall, the Husqvarna Z 448 is a practical and efficient option for homeowners looking to maintain their lawn with ease.

General
BrandHusqvarna
ModelZ 448
Productlawnmower
LanguageEnglish
FiletypeUser manual (PDF)

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Husqvarna Z 448 below.

How short should I cut the grass?

When the grass is longer than 4.5cm, the grass should be cut. The ideal length is between 3 and 4.5cm.

How often should I cut the grass?

In the spring, the grass should be cut every week, while in the summer once every two weeks is sufficient.

Can I mow the lawn when the grass is wet?

You can, but the result is better in dry weather. When the grass is wet, grass clumps can easily form and clog the mower.

How do I engage the park brake on the Husqvarna Z 448 lawnmower?

To engage the park brake on the Husqvarna Z 448 lawnmower, follow these steps: 1. Stop the engine. 2. Remove the ignition key. 3. Ensure the park brake is engaged. 4. Avoid making any adjustments unless the engine is stopped and the ignition key is removed. 5. Be cautious when loading the machine onto a truck or trailer using ramps to prevent any potential injuries. 6. Remember that once the bypasses are engaged and the steering controls are moved to release the parking brake, the unit is free to roll and may cause harm. 7. Use extra care when operating the park brake to ensure safety for yourself and others. 8. Always refer to the operator manual for detailed instructions and safety precautions.

What should I do if the throttle is not responding on the Husqvarna Z 448 lawnmower?

If the throttle is not responding on the Husqvarna Z 448 lawnmower, follow these steps: 1. Check if the throttle control is not stuck or obstructed. 2. Inspect the throttle cable for any damage or disconnection. 3. Ensure that the throttle linkage is properly connected and functioning. 4. Verify that the throttle lever on the engine is moving freely. 5. Clean any debris or dirt around the throttle mechanism. 6. Lubricate the throttle cable and linkage if necessary. 7. If the issue persists, consult a professional for further inspection and repair.

Is the manual of the Husqvarna Z 448 available in English?

Yes, the manual of the Husqvarna Z 448 is available in English .

Is your question not listed? Ask your question here

No results